-
Notifications
You must be signed in to change notification settings - Fork 14
New issue
Have a question about this project? Sign up for a free GitHub account to open an issue and contact its maintainers and the community.
By clicking “Sign up for GitHub”, you agree to our terms of service and privacy statement. We’ll occasionally send you account related emails.
Already on GitHub? Sign in to your account
Extruder 2 spinning with every Z movement! #43
Comments
Do you configure firmware with configurator on line or in manual mode? |
Hi
I used the online configurator.
Tried also mk4duo, but it is the same...
|
So the problem with Z_TWO_STEPPER was activated, there was a bug in the configurator. Open configuration_overall.h and look for Z_TWO_STEPPER and disable it. Or by downloading it with the configurator, click on z one stepper. |
OK - *Got it solved:*
My dual Z steppers are using ONLY ONE DRIVER, so in the configurator tool,
when i choosed DUAL Z STEPPER, it's put "Extruder 1" as default value for Z2
Stepper socket. that's why when moving Z I had additional extruder move: Z2
moved from Z driver, and the extruder moved from "extruder 1" pin allocated
for Z2... :)
THANKS ANYWAY!!!
general question: is there a problem using MK4Duo FW for a simple ramps
1.3? I don't think it's 32 bit...
Thanks again,
Adi
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
בלי
וירוסים. www.avast.com
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
<#m_3701660066328646103_DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
|
MK4duo is a new version a MarlinKimbra for 8 bit and 32 bit... |
Will it work WELL on 16 bit? or shall I install MK?
(I know it is operating my printer noow, but will it be good for it?)
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
בלי
וירוסים. www.avast.com
<https://www.avast.com/sig-email?utm_medium=email&utm_source=link&utm_campaign=sig-email&utm_content=webmail>
<#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2>
…____________________________________________
"יש המטביעים את צרותיהם - ויש המלמדים אותן לשחות..."
"אין מקום שהוא רחוק מדי"
2017-07-07 14:14 GMT+03:00 MagoKimbra <[email protected]>:
MK4duo is a new version a MarlinKimbra for 8 bit and 32 bit...
—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHub
<#43 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AQlZwI0hPB0vne0h3NRAQKfG3gMrlpNgks5sLhMCgaJpZM4OQPCt>
.
|
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Hi
Just updated firmware using the configuration tool. I use singlenozzle configuration with 2 extruders on prusa-like printer.
STRANGE PROBLEM: Every time Z is moving the Extruder 2 is moving too! but when moving the extruder 2, there is no movement of Z axis....
Help will be appreciated!
The text was updated successfully, but these errors were encountered: