diff --git a/.mxproject b/.mxproject index 8811d87a..3eaba3f8 100644 --- a/.mxproject +++ b/.mxproject @@ -1,5 +1,5 @@ [PreviousLibFiles] -LibFiles=Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_adc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_adc_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_adc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_bus.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_rcc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_system.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_utils.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ramfunc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_gpio.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_dma.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_dmamux.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_pwr.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_cortex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_cortex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal.h;Drivers/STM32F4xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_def.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_exti.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_exti.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_can.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_i2c.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_i2c.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_i2c_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_spi.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim_ex.h;Middlewares/Third_Party/FreeRTOS/Source/include/croutine.h;Middlewares/Third_Party/FreeRTOS/Source/include/deprecated_definitions.h;Middlewares/Third_Party/FreeRTOS/Source/include/event_groups.h;Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOS.h;Middlewares/Third_Party/FreeRTOS/Source/include/list.h;Middlewares/Third_Party/FreeRTOS/Source/include/message_buffer.h;Middlewares/Third_Party/FreeRTOS/Source/include/mpu_prototypes.h;Middlewares/Third_Party/FreeRTOS/Source/include/mpu_wrappers.h;Middlewares/Third_Party/FreeRTOS/Source/include/portable.h;Middlewares/Third_Party/FreeRTOS/Source/include/projdefs.h;Middlewares/Third_Party/FreeRTOS/Source/include/queue.h;Middlewares/Third_Party/FreeRTOS/Source/include/semphr.h;Middlewares/Third_Party/FreeRTOS/Source/include/stack_macros.h;Middlewares/Third_Party/FreeRTOS/Source/include/StackMacros.h;Middlewares/Third_Party/FreeRTOS/Source/include/stream_buffer.h;Middlewares/Third_Party/FreeRTOS/Source/include/task.h;Middlewares/Third_Party/FreeRTOS/Source/include/timers.h;Middlewares/Third_Party/FreeRTOS/Source/include/atomic.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/freertos_mpool.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/freertos_os2.h;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/portmacro.h;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_ll_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_exti.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_spi.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c;Middlewares/Third_Party/FreeRTOS/Source/croutine.c;Middlewares/Third_Party/FreeRTOS/Source/event_groups.c;Middlewares/Third_Party/FreeRTOS/Source/list.c;Middlewares/Third_Party/FreeRTOS/Source/queue.c;Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c;Middlewares/Third_Party/FreeRTOS/Source/tasks.c;Middlewares/Third_Party/FreeRTOS/Source/timers.c;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c;Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_adc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_adc_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_adc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_bus.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_rcc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_system.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_utils.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ramfunc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_gpio.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_dma.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_dmamux.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_pwr.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_cortex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_cortex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal.h;Drivers/STM32F4xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_def.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_exti.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_exti.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_can.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_i2c.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_i2c.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_i2c_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_spi.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim_ex.h;Middlewares/Third_Party/FreeRTOS/Source/include/croutine.h;Middlewares/Third_Party/FreeRTOS/Source/include/deprecated_definitions.h;Middlewares/Third_Party/FreeRTOS/Source/include/event_groups.h;Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOS.h;Middlewares/Third_Party/FreeRTOS/Source/include/list.h;Middlewares/Third_Party/FreeRTOS/Source/include/message_buffer.h;Middlewares/Third_Party/FreeRTOS/Source/include/mpu_prototypes.h;Middlewares/Third_Party/FreeRTOS/Source/include/mpu_wrappers.h;Middlewares/Third_Party/FreeRTOS/Source/include/portable.h;Middlewares/Third_Party/FreeRTOS/Source/include/projdefs.h;Middlewares/Third_Party/FreeRTOS/Source/include/queue.h;Middlewares/Third_Party/FreeRTOS/Source/include/semphr.h;Middlewares/Third_Party/FreeRTOS/Source/include/stack_macros.h;Middlewares/Third_Party/FreeRTOS/Source/include/StackMacros.h;Middlewares/Third_Party/FreeRTOS/Source/include/stream_buffer.h;Middlewares/Third_Party/FreeRTOS/Source/include/task.h;Middlewares/Third_Party/FreeRTOS/Source/include/timers.h;Middlewares/Third_Party/FreeRTOS/Source/include/atomic.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/freertos_mpool.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/freertos_os2.h;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/portmacro.h;Drivers/CMSIS/Device/ST/STM32F4xx/Include/stm32f405xx.h;Drivers/CMSIS/Device/ST/STM32F4xx/Include/stm32f4xx.h;Drivers/CMSIS/Device/ST/STM32F4xx/Include/system_stm32f4xx.h;Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c;Drivers/CMSIS/Include/mpu_armv8.h;Drivers/CMSIS/Include/mpu_armv7.h;Drivers/CMSIS/Include/core_cm4.h;Drivers/CMSIS/Include/cmsis_iccarm.h;Drivers/CMSIS/Include/core_cm7.h;Drivers/CMSIS/Include/tz_context.h;Drivers/CMSIS/Include/cmsis_compiler.h;Drivers/CMSIS/Include/core_armv8mml.h;Drivers/CMSIS/Include/core_cm23.h;Drivers/CMSIS/Include/core_sc000.h;Drivers/CMSIS/Include/core_cm1.h;Drivers/CMSIS/Include/cmsis_armclang.h;Drivers/CMSIS/Include/cmsis_gcc.h;Drivers/CMSIS/Include/core_cm0.h;Drivers/CMSIS/Include/core_cm33.h;Drivers/CMSIS/Include/core_armv8mbl.h;Drivers/CMSIS/Include/cmsis_armcc.h;Drivers/CMSIS/Include/core_cm0plus.h;Drivers/CMSIS/Include/core_cm3.h;Drivers/CMSIS/Include/core_sc300.h;Drivers/CMSIS/Include/cmsis_version.h; +LibFiles=Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_adc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_adc_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_adc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_bus.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_rcc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_system.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_utils.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ramfunc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_gpio.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_dma.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_dmamux.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_pwr.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_cortex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_cortex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal.h;Drivers/STM32F4xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_def.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_exti.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_exti.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_can.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_i2c.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_i2c.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_i2c_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_spi.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_uart.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_usart.h;Middlewares/Third_Party/FreeRTOS/Source/include/croutine.h;Middlewares/Third_Party/FreeRTOS/Source/include/deprecated_definitions.h;Middlewares/Third_Party/FreeRTOS/Source/include/event_groups.h;Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOS.h;Middlewares/Third_Party/FreeRTOS/Source/include/list.h;Middlewares/Third_Party/FreeRTOS/Source/include/message_buffer.h;Middlewares/Third_Party/FreeRTOS/Source/include/mpu_prototypes.h;Middlewares/Third_Party/FreeRTOS/Source/include/mpu_wrappers.h;Middlewares/Third_Party/FreeRTOS/Source/include/portable.h;Middlewares/Third_Party/FreeRTOS/Source/include/projdefs.h;Middlewares/Third_Party/FreeRTOS/Source/include/queue.h;Middlewares/Third_Party/FreeRTOS/Source/include/semphr.h;Middlewares/Third_Party/FreeRTOS/Source/include/stack_macros.h;Middlewares/Third_Party/FreeRTOS/Source/include/StackMacros.h;Middlewares/Third_Party/FreeRTOS/Source/include/stream_buffer.h;Middlewares/Third_Party/FreeRTOS/Source/include/task.h;Middlewares/Third_Party/FreeRTOS/Source/include/timers.h;Middlewares/Third_Party/FreeRTOS/Source/include/atomic.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/freertos_mpool.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/freertos_os2.h;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/portmacro.h;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_ll_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_exti.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_spi.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c;Middlewares/Third_Party/FreeRTOS/Source/croutine.c;Middlewares/Third_Party/FreeRTOS/Source/event_groups.c;Middlewares/Third_Party/FreeRTOS/Source/list.c;Middlewares/Third_Party/FreeRTOS/Source/queue.c;Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c;Middlewares/Third_Party/FreeRTOS/Source/tasks.c;Middlewares/Third_Party/FreeRTOS/Source/timers.c;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c;Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_adc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_adc_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_adc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_rcc_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_bus.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_rcc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_system.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_utils.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_flash_ramfunc.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_gpio_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_gpio.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_dma.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_dma.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_dmamux.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_pwr_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_pwr.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_cortex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_cortex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal.h;Drivers/STM32F4xx_HAL_Driver/Inc/Legacy/stm32_hal_legacy.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_def.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_exti.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_exti.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_can.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_i2c.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_i2c.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_i2c_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_spi.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_tim_ex.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_uart.h;Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_usart.h;Middlewares/Third_Party/FreeRTOS/Source/include/croutine.h;Middlewares/Third_Party/FreeRTOS/Source/include/deprecated_definitions.h;Middlewares/Third_Party/FreeRTOS/Source/include/event_groups.h;Middlewares/Third_Party/FreeRTOS/Source/include/FreeRTOS.h;Middlewares/Third_Party/FreeRTOS/Source/include/list.h;Middlewares/Third_Party/FreeRTOS/Source/include/message_buffer.h;Middlewares/Third_Party/FreeRTOS/Source/include/mpu_prototypes.h;Middlewares/Third_Party/FreeRTOS/Source/include/mpu_wrappers.h;Middlewares/Third_Party/FreeRTOS/Source/include/portable.h;Middlewares/Third_Party/FreeRTOS/Source/include/projdefs.h;Middlewares/Third_Party/FreeRTOS/Source/include/queue.h;Middlewares/Third_Party/FreeRTOS/Source/include/semphr.h;Middlewares/Third_Party/FreeRTOS/Source/include/stack_macros.h;Middlewares/Third_Party/FreeRTOS/Source/include/StackMacros.h;Middlewares/Third_Party/FreeRTOS/Source/include/stream_buffer.h;Middlewares/Third_Party/FreeRTOS/Source/include/task.h;Middlewares/Third_Party/FreeRTOS/Source/include/timers.h;Middlewares/Third_Party/FreeRTOS/Source/include/atomic.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/freertos_mpool.h;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/freertos_os2.h;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/portmacro.h;Drivers/CMSIS/Device/ST/STM32F4xx/Include/stm32f405xx.h;Drivers/CMSIS/Device/ST/STM32F4xx/Include/stm32f4xx.h;Drivers/CMSIS/Device/ST/STM32F4xx/Include/system_stm32f4xx.h;Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c;Drivers/CMSIS/Include/mpu_armv8.h;Drivers/CMSIS/Include/mpu_armv7.h;Drivers/CMSIS/Include/core_cm4.h;Drivers/CMSIS/Include/cmsis_iccarm.h;Drivers/CMSIS/Include/core_cm7.h;Drivers/CMSIS/Include/tz_context.h;Drivers/CMSIS/Include/cmsis_compiler.h;Drivers/CMSIS/Include/core_armv8mml.h;Drivers/CMSIS/Include/core_cm23.h;Drivers/CMSIS/Include/core_sc000.h;Drivers/CMSIS/Include/core_cm1.h;Drivers/CMSIS/Include/cmsis_armclang.h;Drivers/CMSIS/Include/cmsis_gcc.h;Drivers/CMSIS/Include/core_cm0.h;Drivers/CMSIS/Include/core_cm33.h;Drivers/CMSIS/Include/core_armv8mbl.h;Drivers/CMSIS/Include/cmsis_armcc.h;Drivers/CMSIS/Include/core_cm0plus.h;Drivers/CMSIS/Include/core_cm3.h;Drivers/CMSIS/Include/core_sc300.h;Drivers/CMSIS/Include/cmsis_version.h; [PreviousUsedCubeIDEFiles] SourceFiles=Core\Src\main.c;Core\Src\freertos.c;Core\Src\stm32f4xx_it.c;Core\Src\stm32f4xx_hal_msp.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_can.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_rcc.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_rcc_ex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_flash.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_flash_ex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_flash_ramfunc.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_gpio.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_dma_ex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_dma.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_pwr.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_pwr_ex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_cortex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_exti.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_tim.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_tim_ex.c;Middlewares\Third_Party\FreeRTOS\Source\croutine.c;Middlewares\Third_Party\FreeRTOS\Source\event_groups.c;Middlewares\Third_Party\FreeRTOS\Source\list.c;Middlewares\Third_Party\FreeRTOS\Source\queue.c;Middlewares\Third_Party\FreeRTOS\Source\stream_buffer.c;Middlewares\Third_Party\FreeRTOS\Source\tasks.c;Middlewares\Third_Party\FreeRTOS\Source\timers.c;Middlewares\Third_Party\FreeRTOS\Source\CMSIS_RTOS_V2\cmsis_os2.c;Middlewares\Third_Party\FreeRTOS\Source\portable\MemMang\heap_4.c;Middlewares\Third_Party\FreeRTOS\Source\portable\GCC\ARM_CM4F\port.c;Drivers\CMSIS\Device\ST\STM32F4xx\Source\Templates\system_stm32f4xx.c;Core\Src\system_stm32f4xx.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_can.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_rcc.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_rcc_ex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_flash.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_flash_ex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_flash_ramfunc.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_gpio.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_dma_ex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_dma.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_pwr.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_pwr_ex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_cortex.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_exti.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_tim.c;Drivers\STM32F4xx_HAL_Driver\Src\stm32f4xx_hal_tim_ex.c;Middlewares\Third_Party\FreeRTOS\Source\croutine.c;Middlewares\Third_Party\FreeRTOS\Source\event_groups.c;Middlewares\Third_Party\FreeRTOS\Source\list.c;Middlewares\Third_Party\FreeRTOS\Source\queue.c;Middlewares\Third_Party\FreeRTOS\Source\stream_buffer.c;Middlewares\Third_Party\FreeRTOS\Source\tasks.c;Middlewares\Third_Party\FreeRTOS\Source\timers.c;Middlewares\Third_Party\FreeRTOS\Source\CMSIS_RTOS_V2\cmsis_os2.c;Middlewares\Third_Party\FreeRTOS\Source\portable\MemMang\heap_4.c;Middlewares\Third_Party\FreeRTOS\Source\portable\GCC\ARM_CM4F\port.c;Drivers\CMSIS\Device\ST\STM32F4xx\Source\Templates\system_stm32f4xx.c;Core\Src\system_stm32f4xx.c;;;Middlewares\Third_Party\FreeRTOS\Source\croutine.c;Middlewares\Third_Party\FreeRTOS\Source\event_groups.c;Middlewares\Third_Party\FreeRTOS\Source\list.c;Middlewares\Third_Party\FreeRTOS\Source\queue.c;Middlewares\Third_Party\FreeRTOS\Source\stream_buffer.c;Middlewares\Third_Party\FreeRTOS\Source\tasks.c;Middlewares\Third_Party\FreeRTOS\Source\timers.c;Middlewares\Third_Party\FreeRTOS\Source\CMSIS_RTOS_V2\cmsis_os2.c;Middlewares\Third_Party\FreeRTOS\Source\portable\MemMang\heap_4.c;Middlewares\Third_Party\FreeRTOS\Source\portable\GCC\ARM_CM4F\port.c; @@ -7,7 +7,7 @@ HeaderPath=Drivers\STM32F4xx_HAL_Driver\Inc;Drivers\STM32F4xx_HAL_Driver\Inc\Leg CDefines=USE_HAL_DRIVER;STM32F405xx;USE_HAL_DRIVER;USE_HAL_DRIVER; [PreviousUsedMakefileFiles] -SourceFiles=Core/Src/main.c;Core/Src/freertos.c;Core/Src/stm32f4xx_it.c;Core/Src/stm32f4xx_hal_msp.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_ll_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_exti.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_spi.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c;Middlewares/Third_Party/FreeRTOS/Source/croutine.c;Middlewares/Third_Party/FreeRTOS/Source/event_groups.c;Middlewares/Third_Party/FreeRTOS/Source/list.c;Middlewares/Third_Party/FreeRTOS/Source/queue.c;Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c;Middlewares/Third_Party/FreeRTOS/Source/tasks.c;Middlewares/Third_Party/FreeRTOS/Source/timers.c;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c;Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c;Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c;Core/Src/system_stm32f4xx.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_ll_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_exti.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_spi.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c;Middlewares/Third_Party/FreeRTOS/Source/croutine.c;Middlewares/Third_Party/FreeRTOS/Source/event_groups.c;Middlewares/Third_Party/FreeRTOS/Source/list.c;Middlewares/Third_Party/FreeRTOS/Source/queue.c;Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c;Middlewares/Third_Party/FreeRTOS/Source/tasks.c;Middlewares/Third_Party/FreeRTOS/Source/timers.c;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c;Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c;Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c;Core/Src/system_stm32f4xx.c;;;Middlewares/Third_Party/FreeRTOS/Source/croutine.c;Middlewares/Third_Party/FreeRTOS/Source/event_groups.c;Middlewares/Third_Party/FreeRTOS/Source/list.c;Middlewares/Third_Party/FreeRTOS/Source/queue.c;Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c;Middlewares/Third_Party/FreeRTOS/Source/tasks.c;Middlewares/Third_Party/FreeRTOS/Source/timers.c;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c;Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c; +SourceFiles=Core/Src/main.c;Core/Src/freertos.c;Core/Src/stm32f4xx_it.c;Core/Src/stm32f4xx_hal_msp.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_ll_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_exti.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_spi.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c;Middlewares/Third_Party/FreeRTOS/Source/croutine.c;Middlewares/Third_Party/FreeRTOS/Source/event_groups.c;Middlewares/Third_Party/FreeRTOS/Source/list.c;Middlewares/Third_Party/FreeRTOS/Source/queue.c;Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c;Middlewares/Third_Party/FreeRTOS/Source/tasks.c;Middlewares/Third_Party/FreeRTOS/Source/timers.c;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c;Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c;Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c;Core/Src/system_stm32f4xx.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_adc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_ll_adc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_flash_ramfunc.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_gpio.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_dma.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_pwr_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_cortex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_exti.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_i2c_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_spi.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_tim_ex.c;Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c;Middlewares/Third_Party/FreeRTOS/Source/croutine.c;Middlewares/Third_Party/FreeRTOS/Source/event_groups.c;Middlewares/Third_Party/FreeRTOS/Source/list.c;Middlewares/Third_Party/FreeRTOS/Source/queue.c;Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c;Middlewares/Third_Party/FreeRTOS/Source/tasks.c;Middlewares/Third_Party/FreeRTOS/Source/timers.c;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c;Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c;Drivers/CMSIS/Device/ST/STM32F4xx/Source/Templates/system_stm32f4xx.c;Core/Src/system_stm32f4xx.c;;;Middlewares/Third_Party/FreeRTOS/Source/croutine.c;Middlewares/Third_Party/FreeRTOS/Source/event_groups.c;Middlewares/Third_Party/FreeRTOS/Source/list.c;Middlewares/Third_Party/FreeRTOS/Source/queue.c;Middlewares/Third_Party/FreeRTOS/Source/stream_buffer.c;Middlewares/Third_Party/FreeRTOS/Source/tasks.c;Middlewares/Third_Party/FreeRTOS/Source/timers.c;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c;Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c; HeaderPath=Drivers/STM32F4xx_HAL_Driver/Inc;Drivers/STM32F4xx_HAL_Driver/Inc/Legacy;Middlewares/Third_Party/FreeRTOS/Source/include;Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2;Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F;Drivers/CMSIS/Device/ST/STM32F4xx/Include;Drivers/CMSIS/Include;Core/Inc; CDefines=USE_HAL_DRIVER;STM32F405xx;USE_HAL_DRIVER;USE_HAL_DRIVER; diff --git a/Core/Inc/serial_monitor.h b/Core/Inc/serial_monitor.h new file mode 100644 index 00000000..ac48dd57 --- /dev/null +++ b/Core/Inc/serial_monitor.h @@ -0,0 +1,15 @@ +#ifndef SERIAL_MONITOR_H +#define SERIAL_MONITOR_H + +#include "cmsis_os.h" + +/* Function to queue a message to be sent on the UART stream */ +int serial_print(const char* format, ...); + +/* Defining Temperature Monitor Task */ +void vSerialMonitor(void* pv_params); + +extern osThreadId_t serial_monitor_handle; +extern const osThreadAttr_t serial_monitor_attributes; + +#endif // SERIAL_MONITOR_H diff --git a/Core/Inc/stm32f4xx_hal_conf.h b/Core/Inc/stm32f4xx_hal_conf.h index ceb43933..66526d2c 100644 --- a/Core/Inc/stm32f4xx_hal_conf.h +++ b/Core/Inc/stm32f4xx_hal_conf.h @@ -64,7 +64,7 @@ /* #define HAL_MMC_MODULE_ENABLED */ #define HAL_SPI_MODULE_ENABLED /* #define HAL_TIM_MODULE_ENABLED */ -/* #define HAL_UART_MODULE_ENABLED */ +#define HAL_UART_MODULE_ENABLED /* #define HAL_USART_MODULE_ENABLED */ /* #define HAL_IRDA_MODULE_ENABLED */ /* #define HAL_SMARTCARD_MODULE_ENABLED */ diff --git a/Core/Src/main.c b/Core/Src/main.c index 80f64d67..6a9514d4 100644 --- a/Core/Src/main.c +++ b/Core/Src/main.c @@ -1,583 +1,636 @@ -/* USER CODE BEGIN Header */ -/** - ****************************************************************************** - * @file : main.c - * @brief : Main program body - ****************************************************************************** - * @attention - * - * Copyright (c) 2023 STMicroelectronics. - * All rights reserved. - * - * This software is licensed under terms that can be found in the LICENSE file - * in the root directory of this software component. - * If no LICENSE file comes with this software, it is provided AS-IS. - * - ****************************************************************************** - */ -/* USER CODE END Header */ -/* Includes ------------------------------------------------------------------*/ -#include "main.h" -#include "cmsis_os.h" - -/* Private includes ----------------------------------------------------------*/ -/* USER CODE BEGIN Includes */ -#include "sht30.h" -#include "monitor.h" -#include "queues.h" -#include "fault.h" -#include "can_handler.h" -/* USER CODE END Includes */ - -/* Private typedef -----------------------------------------------------------*/ -/* USER CODE BEGIN PTD */ - -/* USER CODE END PTD */ - -/* Private define ------------------------------------------------------------*/ -/* USER CODE BEGIN PD */ - -/* USER CODE END PD */ - -/* Private macro -------------------------------------------------------------*/ -/* USER CODE BEGIN PM */ - -/* USER CODE END PM */ - -/* Private variables ---------------------------------------------------------*/ -ADC_HandleTypeDef hadc1; - -CAN_HandleTypeDef hcan1; - -I2C_HandleTypeDef hi2c1; -I2C_HandleTypeDef hi2c2; - -SPI_HandleTypeDef hspi1; -SPI_HandleTypeDef hspi2; - -/* Definitions for defaultTask */ -osThreadId_t defaultTaskHandle; -const osThreadAttr_t defaultTask_attributes = { - .name = "defaultTask", - .stack_size = 128 * 4, - .priority = (osPriority_t) osPriorityNormal, -}; -/* USER CODE BEGIN PV */ -osMessageQueueId_t onboard_temp_queue; -osMessageQueueId_t pedal_data_queue; -osMessageQueueId_t imu_queue; -/* USER CODE END PV */ - -/* Private function prototypes -----------------------------------------------*/ -void SystemClock_Config(void); -static void MX_GPIO_Init(void); -static void MX_CAN1_Init(void); -static void MX_I2C1_Init(void); -static void MX_I2C2_Init(void); -static void MX_SPI1_Init(void); -static void MX_SPI2_Init(void); -static void MX_ADC1_Init(void); -void StartDefaultTask(void *argument); - -/* USER CODE BEGIN PFP */ - -/* USER CODE END PFP */ - -/* Private user code ---------------------------------------------------------*/ -/* USER CODE BEGIN 0 */ - -/* USER CODE END 0 */ - -/** - * @brief The application entry point. - * @retval int - */ -int main(void) -{ - /* USER CODE BEGIN 1 */ - - /* USER CODE END 1 */ - - /* MCU Configuration--------------------------------------------------------*/ - - /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ - HAL_Init(); - - /* USER CODE BEGIN Init */ - - /* USER CODE END Init */ - - /* Configure the system clock */ - SystemClock_Config(); - - /* USER CODE BEGIN SysInit */ - - /* USER CODE END SysInit */ - - /* Initialize all configured peripherals */ - MX_GPIO_Init(); - MX_CAN1_Init(); - MX_I2C1_Init(); - MX_I2C2_Init(); - MX_SPI1_Init(); - MX_SPI2_Init(); - MX_ADC1_Init(); - /* USER CODE BEGIN 2 */ - - /* USER CODE END 2 */ - - /* Init scheduler */ - osKernelInitialize(); - - /* USER CODE BEGIN RTOS_MUTEX */ - /* add mutexes, ... */ - /* USER CODE END RTOS_MUTEX */ - - /* USER CODE BEGIN RTOS_SEMAPHORES */ - /* add semaphores, ... */ - /* USER CODE END RTOS_SEMAPHORES */ - - /* USER CODE BEGIN RTOS_TIMERS */ - /* start timers, add new ones, ... */ - /* USER CODE END RTOS_TIMERS */ - - /* USER CODE BEGIN RTOS_QUEUES */ - onboard_temp_queue = osMessageQueueNew(ONBOARD_TEMP_QUEUE_SIZE, sizeof(onboard_temp_t), NULL); - fault_handle_queue = osMessageQueueNew(FAULT_HANDLE_QUEUE_SIZE, sizeof(fault_data_t), NULL); - imu_queue = osMessageQueueNew(IMU_QUEUE_SIZE, sizeof(imu_data_t), NULL); - pedal_data_queue = osMessageQueueNew(PEDAL_DATA_QUEUE_SIZE, sizeof(pedals_t), NULL); - /* USER CODE END RTOS_QUEUES */ - - /* Create the thread(s) */ - /* creation of defaultTask */ - defaultTaskHandle = osThreadNew(StartDefaultTask, NULL, &defaultTask_attributes); - - /* USER CODE BEGIN RTOS_THREADS */ - temp_monitor_handle = osThreadNew(vTempMonitor, &hi2c1, &temp_monitor_attributes); - watchdog_monitor_handle = osThreadNew(vWatchdogMonitor, GPIOB, &watchdog_monitor_attributes); - imu_monitor_handle = osThreadNew(vIMUMonitor, &hi2c1, &imu_monitor_attributes); - - //TODO: Get correct ADC/GPIO value - pedals_monitor_handle = osThreadNew(vPedalsMonitor, &hadc1, &pedals_monitor_attributes); - route_can_incoming_handle = osThreadNew(vRouteCanIncoming, &hcan1, &route_can_incoming_attributes); - - /* USER CODE END RTOS_THREADS */ - - /* USER CODE BEGIN RTOS_EVENTS */ - /* add events, ... */ - /* USER CODE END RTOS_EVENTS */ - - /* Start scheduler */ - osKernelStart(); - /* We should never get here as control is now taken by the scheduler */ - /* Infinite loop */ - /* USER CODE BEGIN WHILE */ - while (1) - { - /* USER CODE END WHILE */ - - /* USER CODE BEGIN 3 */ - } - /* USER CODE END 3 */ -} - -/** - * @brief System Clock Configuration - * @retval None - */ -void SystemClock_Config(void) -{ - RCC_OscInitTypeDef RCC_OscInitStruct = {0}; - RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; - - /** Configure the main internal regulator output voltage - */ - __HAL_RCC_PWR_CLK_ENABLE(); - __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); - - /** Initializes the RCC Oscillators according to the specified parameters - * in the RCC_OscInitTypeDef structure. - */ - RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI; - RCC_OscInitStruct.HSIState = RCC_HSI_ON; - RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; - RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE; - if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) - { - Error_Handler(); - } - - /** Initializes the CPU, AHB and APB buses clocks - */ - RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK - |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2; - RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI; - RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; - RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; - RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; - - if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK) - { - Error_Handler(); - } -} - -/** - * @brief ADC1 Initialization Function - * @param None - * @retval None - */ -static void MX_ADC1_Init(void) -{ - - /* USER CODE BEGIN ADC1_Init 0 */ - - /* USER CODE END ADC1_Init 0 */ - - ADC_ChannelConfTypeDef sConfig = {0}; - - /* USER CODE BEGIN ADC1_Init 1 */ - - /* USER CODE END ADC1_Init 1 */ - - /** Configure the global features of the ADC (Clock, Resolution, Data Alignment and number of conversion) - */ - hadc1.Instance = ADC1; - hadc1.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV2; - hadc1.Init.Resolution = ADC_RESOLUTION_12B; - hadc1.Init.ScanConvMode = DISABLE; - hadc1.Init.ContinuousConvMode = DISABLE; - hadc1.Init.DiscontinuousConvMode = DISABLE; - hadc1.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE; - hadc1.Init.ExternalTrigConv = ADC_SOFTWARE_START; - hadc1.Init.DataAlign = ADC_DATAALIGN_RIGHT; - hadc1.Init.NbrOfConversion = 1; - hadc1.Init.DMAContinuousRequests = DISABLE; - hadc1.Init.EOCSelection = ADC_EOC_SINGLE_CONV; - if (HAL_ADC_Init(&hadc1) != HAL_OK) - { - Error_Handler(); - } - - /** Configure for the selected ADC regular channel its corresponding rank in the sequencer and its sample time. - */ - sConfig.Channel = ADC_CHANNEL_0; - sConfig.Rank = 1; - sConfig.SamplingTime = ADC_SAMPLETIME_3CYCLES; - if (HAL_ADC_ConfigChannel(&hadc1, &sConfig) != HAL_OK) - { - Error_Handler(); - } - /* USER CODE BEGIN ADC1_Init 2 */ - - /* USER CODE END ADC1_Init 2 */ - -} - -/** - * @brief CAN1 Initialization Function - * @param None - * @retval None - */ -static void MX_CAN1_Init(void) -{ - - /* USER CODE BEGIN CAN1_Init 0 */ - - /* USER CODE END CAN1_Init 0 */ - - /* USER CODE BEGIN CAN1_Init 1 */ - - /* USER CODE END CAN1_Init 1 */ - hcan1.Instance = CAN1; - hcan1.Init.Prescaler = 16; - hcan1.Init.Mode = CAN_MODE_NORMAL; - hcan1.Init.SyncJumpWidth = CAN_SJW_1TQ; - hcan1.Init.TimeSeg1 = CAN_BS1_1TQ; - hcan1.Init.TimeSeg2 = CAN_BS2_1TQ; - hcan1.Init.TimeTriggeredMode = DISABLE; - hcan1.Init.AutoBusOff = DISABLE; - hcan1.Init.AutoWakeUp = DISABLE; - hcan1.Init.AutoRetransmission = DISABLE; - hcan1.Init.ReceiveFifoLocked = DISABLE; - hcan1.Init.TransmitFifoPriority = DISABLE; - if (HAL_CAN_Init(&hcan1) != HAL_OK) - { - Error_Handler(); - } - /* USER CODE BEGIN CAN1_Init 2 */ - - /* USER CODE END CAN1_Init 2 */ - -} - -/** - * @brief I2C1 Initialization Function - * @param None - * @retval None - */ -static void MX_I2C1_Init(void) -{ - - /* USER CODE BEGIN I2C1_Init 0 */ - - /* USER CODE END I2C1_Init 0 */ - - /* USER CODE BEGIN I2C1_Init 1 */ - - /* USER CODE END I2C1_Init 1 */ - hi2c1.Instance = I2C1; - hi2c1.Init.ClockSpeed = 100000; - hi2c1.Init.DutyCycle = I2C_DUTYCYCLE_2; - hi2c1.Init.OwnAddress1 = 0; - hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT; - hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE; - hi2c1.Init.OwnAddress2 = 0; - hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE; - hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE; - if (HAL_I2C_Init(&hi2c1) != HAL_OK) - { - Error_Handler(); - } - /* USER CODE BEGIN I2C1_Init 2 */ - - /* USER CODE END I2C1_Init 2 */ - -} - -/** - * @brief I2C2 Initialization Function - * @param None - * @retval None - */ -static void MX_I2C2_Init(void) -{ - - /* USER CODE BEGIN I2C2_Init 0 */ - - /* USER CODE END I2C2_Init 0 */ - - /* USER CODE BEGIN I2C2_Init 1 */ - - /* USER CODE END I2C2_Init 1 */ - hi2c2.Instance = I2C2; - hi2c2.Init.ClockSpeed = 100000; - hi2c2.Init.DutyCycle = I2C_DUTYCYCLE_2; - hi2c2.Init.OwnAddress1 = 0; - hi2c2.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT; - hi2c2.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE; - hi2c2.Init.OwnAddress2 = 0; - hi2c2.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE; - hi2c2.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE; - if (HAL_I2C_Init(&hi2c2) != HAL_OK) - { - Error_Handler(); - } - /* USER CODE BEGIN I2C2_Init 2 */ - - /* USER CODE END I2C2_Init 2 */ - -} - -/** - * @brief SPI1 Initialization Function - * @param None - * @retval None - */ -static void MX_SPI1_Init(void) -{ - - /* USER CODE BEGIN SPI1_Init 0 */ - - /* USER CODE END SPI1_Init 0 */ - - /* USER CODE BEGIN SPI1_Init 1 */ - - /* USER CODE END SPI1_Init 1 */ - /* SPI1 parameter configuration*/ - hspi1.Instance = SPI1; - hspi1.Init.Mode = SPI_MODE_MASTER; - hspi1.Init.Direction = SPI_DIRECTION_2LINES; - hspi1.Init.DataSize = SPI_DATASIZE_8BIT; - hspi1.Init.CLKPolarity = SPI_POLARITY_LOW; - hspi1.Init.CLKPhase = SPI_PHASE_1EDGE; - hspi1.Init.NSS = SPI_NSS_SOFT; - hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2; - hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB; - hspi1.Init.TIMode = SPI_TIMODE_DISABLE; - hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE; - hspi1.Init.CRCPolynomial = 10; - if (HAL_SPI_Init(&hspi1) != HAL_OK) - { - Error_Handler(); - } - /* USER CODE BEGIN SPI1_Init 2 */ - - /* USER CODE END SPI1_Init 2 */ - -} - -/** - * @brief SPI2 Initialization Function - * @param None - * @retval None - */ -static void MX_SPI2_Init(void) -{ - - /* USER CODE BEGIN SPI2_Init 0 */ - - /* USER CODE END SPI2_Init 0 */ - - /* USER CODE BEGIN SPI2_Init 1 */ - - /* USER CODE END SPI2_Init 1 */ - /* SPI2 parameter configuration*/ - hspi2.Instance = SPI2; - hspi2.Init.Mode = SPI_MODE_MASTER; - hspi2.Init.Direction = SPI_DIRECTION_2LINES; - hspi2.Init.DataSize = SPI_DATASIZE_8BIT; - hspi2.Init.CLKPolarity = SPI_POLARITY_LOW; - hspi2.Init.CLKPhase = SPI_PHASE_1EDGE; - hspi2.Init.NSS = SPI_NSS_SOFT; - hspi2.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2; - hspi2.Init.FirstBit = SPI_FIRSTBIT_MSB; - hspi2.Init.TIMode = SPI_TIMODE_DISABLE; - hspi2.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE; - hspi2.Init.CRCPolynomial = 10; - if (HAL_SPI_Init(&hspi2) != HAL_OK) - { - Error_Handler(); - } - /* USER CODE BEGIN SPI2_Init 2 */ - - /* USER CODE END SPI2_Init 2 */ - -} - -/** - * @brief GPIO Initialization Function - * @param None - * @retval None - */ -static void MX_GPIO_Init(void) -{ - GPIO_InitTypeDef GPIO_InitStruct = {0}; -/* USER CODE BEGIN MX_GPIO_Init_1 */ -/* USER CODE END MX_GPIO_Init_1 */ - - /* GPIO Ports Clock Enable */ - __HAL_RCC_GPIOH_CLK_ENABLE(); - __HAL_RCC_GPIOC_CLK_ENABLE(); - __HAL_RCC_GPIOA_CLK_ENABLE(); - __HAL_RCC_GPIOB_CLK_ENABLE(); - - /*Configure GPIO pin Output Level */ - HAL_GPIO_WritePin(GPIOC, GPIO_PIN_8|GPIO_PIN_9, GPIO_PIN_RESET); - - /*Configure GPIO pins : PC4 PC5 */ - GPIO_InitStruct.Pin = GPIO_PIN_4|GPIO_PIN_5; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); - - /*Configure GPIO pins : PB0 PB1 */ - GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); - - /*Configure GPIO pin : PB2 */ - GPIO_InitStruct.Pin = GPIO_PIN_2; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; - GPIO_InitStruct.Alternate = GPIO_AF15_EVENTOUT; - HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); - - /*Configure GPIO pins : PC8 PC9 */ - GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9; - GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; - HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); - - /*Configure GPIO pin : PA9 */ - GPIO_InitStruct.Pin = GPIO_PIN_9; - GPIO_InitStruct.Mode = GPIO_MODE_INPUT; - GPIO_InitStruct.Pull = GPIO_NOPULL; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /*Configure GPIO pins : PA11 PA12 */ - GPIO_InitStruct.Pin = GPIO_PIN_11|GPIO_PIN_12; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; - HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); - - /*Configure GPIO pins : PC10 PC11 */ - GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11; - GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; - GPIO_InitStruct.Pull = GPIO_NOPULL; - GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; - GPIO_InitStruct.Alternate = GPIO_AF7_USART3; - HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); - -/* USER CODE BEGIN MX_GPIO_Init_2 */ -/* USER CODE END MX_GPIO_Init_2 */ -} - -/* USER CODE BEGIN 4 */ - -/* USER CODE END 4 */ - -/* USER CODE BEGIN Header_StartDefaultTask */ -/** - * @brief Function implementing the defaultTask thread. - * @param argument: Not used - * @retval None - */ -/* USER CODE END Header_StartDefaultTask */ -void StartDefaultTask(void *argument) -{ - /* USER CODE BEGIN 5 */ - /* Infinite loop */ - for(;;) - { - osDelay(1); - } - /* USER CODE END 5 */ -} - -/** - * @brief This function is executed in case of error occurrence. - * @retval None - */ -void Error_Handler(void) -{ - /* USER CODE BEGIN Error_Handler_Debug */ - /* User can add his own implementation to report the HAL error return state */ - __disable_irq(); - while (1) - { - } - /* USER CODE END Error_Handler_Debug */ -} - -#ifdef USE_FULL_ASSERT -/** - * @brief Reports the name of the source file and the source line number - * where the assert_param error has occurred. - * @param file: pointer to the source file name - * @param line: assert_param error line source number - * @retval None - */ -void assert_failed(uint8_t *file, uint32_t line) -{ - /* USER CODE BEGIN 6 */ - /* User can add his own implementation to report the file name and line number, - ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ - /* USER CODE END 6 */ -} -#endif /* USE_FULL_ASSERT */ +/* USER CODE BEGIN Header */ +/** + ****************************************************************************** + * @file : main.c + * @brief : Main program body + ****************************************************************************** + * @attention + * + * Copyright (c) 2023 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + */ +/* USER CODE END Header */ +/* Includes ------------------------------------------------------------------*/ +#include "main.h" +#include "cmsis_os.h" + +/* Private includes ----------------------------------------------------------*/ +/* USER CODE BEGIN Includes */ +#include +#include "sht30.h" +#include "monitor.h" +#include "queues.h" +#include "fault.h" +#include "can_handler.h" +#include "serial_monitor.h" +/* USER CODE END Includes */ + +/* Private typedef -----------------------------------------------------------*/ +/* USER CODE BEGIN PTD */ + +/* USER CODE END PTD */ + +/* Private define ------------------------------------------------------------*/ +/* USER CODE BEGIN PD */ + +/* USER CODE END PD */ + +/* Private macro -------------------------------------------------------------*/ +/* USER CODE BEGIN PM */ + +/* USER CODE END PM */ + +/* Private variables ---------------------------------------------------------*/ +ADC_HandleTypeDef hadc1; + +CAN_HandleTypeDef hcan1; + +I2C_HandleTypeDef hi2c1; +I2C_HandleTypeDef hi2c2; + +SPI_HandleTypeDef hspi1; +SPI_HandleTypeDef hspi2; + +UART_HandleTypeDef huart3; + +/* Definitions for defaultTask */ +osThreadId_t defaultTaskHandle; +const osThreadAttr_t defaultTask_attributes = { + .name = "defaultTask", + .stack_size = 128 * 4, + .priority = (osPriority_t) osPriorityNormal, +}; +/* USER CODE BEGIN PV */ +osMessageQueueId_t onboard_temp_queue; +osMessageQueueId_t pedal_data_queue; +osMessageQueueId_t imu_queue; +/* USER CODE END PV */ + +/* Private function prototypes -----------------------------------------------*/ +void SystemClock_Config(void); +static void MX_GPIO_Init(void); +static void MX_CAN1_Init(void); +static void MX_I2C1_Init(void); +static void MX_I2C2_Init(void); +static void MX_SPI1_Init(void); +static void MX_SPI2_Init(void); +static void MX_ADC1_Init(void); +static void MX_USART3_UART_Init(void); +void StartDefaultTask(void *argument); + +/* USER CODE BEGIN PFP */ + +/* USER CODE END PFP */ + +/* Private user code ---------------------------------------------------------*/ +/* USER CODE BEGIN 0 */ +/* Snippet of code from Digikey Example of printf redirection */ +#ifdef __GNUC__ +#define PUTCHAR_PROTOTYPE int __io_putchar(int ch) +#else +#define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f) +#endif + +PUTCHAR_PROTOTYPE +{ + HAL_UART_Transmit(&huart3, (uint8_t *)&ch, 1, HAL_MAX_DELAY); + return ch; +} + +int _write(int file, char* ptr, int len) { + int DataIdx; + + for (DataIdx = 0; DataIdx < len; DataIdx++) { + __io_putchar( *ptr++ ); + } + return len; +} +/* USER CODE END 0 */ + +/** + * @brief The application entry point. + * @retval int + */ +int main(void) +{ + /* USER CODE BEGIN 1 */ + + /* USER CODE END 1 */ + + /* MCU Configuration--------------------------------------------------------*/ + + /* Reset of all peripherals, Initializes the Flash interface and the Systick. */ + HAL_Init(); + + /* USER CODE BEGIN Init */ + + /* USER CODE END Init */ + + /* Configure the system clock */ + SystemClock_Config(); + + /* USER CODE BEGIN SysInit */ + + /* USER CODE END SysInit */ + + /* Initialize all configured peripherals */ + MX_GPIO_Init(); + MX_CAN1_Init(); + MX_I2C1_Init(); + MX_I2C2_Init(); + MX_SPI1_Init(); + MX_SPI2_Init(); + MX_ADC1_Init(); + MX_USART3_UART_Init(); + /* USER CODE BEGIN 2 */ + + /* USER CODE END 2 */ + + /* Init scheduler */ + osKernelInitialize(); + + /* USER CODE BEGIN RTOS_MUTEX */ + /* add mutexes, ... */ + /* USER CODE END RTOS_MUTEX */ + + /* USER CODE BEGIN RTOS_SEMAPHORES */ + /* add semaphores, ... */ + /* USER CODE END RTOS_SEMAPHORES */ + + /* USER CODE BEGIN RTOS_TIMERS */ + /* start timers, add new ones, ... */ + /* USER CODE END RTOS_TIMERS */ + + /* USER CODE BEGIN RTOS_QUEUES */ + onboard_temp_queue = osMessageQueueNew(ONBOARD_TEMP_QUEUE_SIZE, sizeof(onboard_temp_t), NULL); + fault_handle_queue = osMessageQueueNew(FAULT_HANDLE_QUEUE_SIZE, sizeof(fault_data_t), NULL); + imu_queue = osMessageQueueNew(IMU_QUEUE_SIZE, sizeof(imu_data_t), NULL); + pedal_data_queue = osMessageQueueNew(PEDAL_DATA_QUEUE_SIZE, sizeof(pedals_t), NULL); + /* USER CODE END RTOS_QUEUES */ + + /* Create the thread(s) */ + /* creation of defaultTask */ + defaultTaskHandle = osThreadNew(StartDefaultTask, NULL, &defaultTask_attributes); + + /* USER CODE BEGIN RTOS_THREADS */ + temp_monitor_handle = osThreadNew(vTempMonitor, &hi2c1, &temp_monitor_attributes); + watchdog_monitor_handle = osThreadNew(vWatchdogMonitor, GPIOB, &watchdog_monitor_attributes); + imu_monitor_handle = osThreadNew(vIMUMonitor, &hi2c1, &imu_monitor_attributes); + serial_monitor_handle = osThreadNew(vSerialMonitor, NULL, &serial_monitor_attributes); + + //TODO: Get correct ADC/GPIO value + pedals_monitor_handle = osThreadNew(vPedalsMonitor, &hadc1, &pedals_monitor_attributes); + route_can_incoming_handle = osThreadNew(vRouteCanIncoming, &hcan1, &route_can_incoming_attributes); + + /* USER CODE END RTOS_THREADS */ + + /* USER CODE BEGIN RTOS_EVENTS */ + /* add events, ... */ + /* USER CODE END RTOS_EVENTS */ + /* Start scheduler */ + osKernelStart(); + /* We should never get here as control is now taken by the scheduler */ + /* Infinite loop */ + /* USER CODE BEGIN WHILE */ + while (1) + { + /* USER CODE END WHILE */ + + /* USER CODE BEGIN 3 */ + } + /* USER CODE END 3 */ +} + +/** + * @brief System Clock Configuration + * @retval None + */ +void SystemClock_Config(void) +{ + RCC_OscInitTypeDef RCC_OscInitStruct = {0}; + RCC_ClkInitTypeDef RCC_ClkInitStruct = {0}; + + /** Configure the main internal regulator output voltage + */ + __HAL_RCC_PWR_CLK_ENABLE(); + __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1); + + /** Initializes the RCC Oscillators according to the specified parameters + * in the RCC_OscInitTypeDef structure. + */ + RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI; + RCC_OscInitStruct.HSIState = RCC_HSI_ON; + RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT; + RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE; + if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) + { + Error_Handler(); + } + + /** Initializes the CPU, AHB and APB buses clocks + */ + RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK + |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2; + RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI; + RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1; + RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1; + RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1; + + if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK) + { + Error_Handler(); + } +} + +/** + * @brief ADC1 Initialization Function + * @param None + * @retval None + */ +static void MX_ADC1_Init(void) +{ + + /* USER CODE BEGIN ADC1_Init 0 */ + + /* USER CODE END ADC1_Init 0 */ + + ADC_ChannelConfTypeDef sConfig = {0}; + + /* USER CODE BEGIN ADC1_Init 1 */ + + /* USER CODE END ADC1_Init 1 */ + + /** Configure the global features of the ADC (Clock, Resolution, Data Alignment and number of conversion) + */ + hadc1.Instance = ADC1; + hadc1.Init.ClockPrescaler = ADC_CLOCK_SYNC_PCLK_DIV2; + hadc1.Init.Resolution = ADC_RESOLUTION_12B; + hadc1.Init.ScanConvMode = DISABLE; + hadc1.Init.ContinuousConvMode = DISABLE; + hadc1.Init.DiscontinuousConvMode = DISABLE; + hadc1.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE; + hadc1.Init.ExternalTrigConv = ADC_SOFTWARE_START; + hadc1.Init.DataAlign = ADC_DATAALIGN_RIGHT; + hadc1.Init.NbrOfConversion = 1; + hadc1.Init.DMAContinuousRequests = DISABLE; + hadc1.Init.EOCSelection = ADC_EOC_SINGLE_CONV; + if (HAL_ADC_Init(&hadc1) != HAL_OK) + { + Error_Handler(); + } + + /** Configure for the selected ADC regular channel its corresponding rank in the sequencer and its sample time. + */ + sConfig.Channel = ADC_CHANNEL_0; + sConfig.Rank = 1; + sConfig.SamplingTime = ADC_SAMPLETIME_3CYCLES; + if (HAL_ADC_ConfigChannel(&hadc1, &sConfig) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN ADC1_Init 2 */ + + /* USER CODE END ADC1_Init 2 */ + +} + +/** + * @brief CAN1 Initialization Function + * @param None + * @retval None + */ +static void MX_CAN1_Init(void) +{ + + /* USER CODE BEGIN CAN1_Init 0 */ + + /* USER CODE END CAN1_Init 0 */ + + /* USER CODE BEGIN CAN1_Init 1 */ + + /* USER CODE END CAN1_Init 1 */ + hcan1.Instance = CAN1; + hcan1.Init.Prescaler = 16; + hcan1.Init.Mode = CAN_MODE_NORMAL; + hcan1.Init.SyncJumpWidth = CAN_SJW_1TQ; + hcan1.Init.TimeSeg1 = CAN_BS1_1TQ; + hcan1.Init.TimeSeg2 = CAN_BS2_1TQ; + hcan1.Init.TimeTriggeredMode = DISABLE; + hcan1.Init.AutoBusOff = DISABLE; + hcan1.Init.AutoWakeUp = DISABLE; + hcan1.Init.AutoRetransmission = DISABLE; + hcan1.Init.ReceiveFifoLocked = DISABLE; + hcan1.Init.TransmitFifoPriority = DISABLE; + if (HAL_CAN_Init(&hcan1) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN CAN1_Init 2 */ + + /* USER CODE END CAN1_Init 2 */ + +} + +/** + * @brief I2C1 Initialization Function + * @param None + * @retval None + */ +static void MX_I2C1_Init(void) +{ + + /* USER CODE BEGIN I2C1_Init 0 */ + + /* USER CODE END I2C1_Init 0 */ + + /* USER CODE BEGIN I2C1_Init 1 */ + + /* USER CODE END I2C1_Init 1 */ + hi2c1.Instance = I2C1; + hi2c1.Init.ClockSpeed = 100000; + hi2c1.Init.DutyCycle = I2C_DUTYCYCLE_2; + hi2c1.Init.OwnAddress1 = 0; + hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT; + hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE; + hi2c1.Init.OwnAddress2 = 0; + hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE; + hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE; + if (HAL_I2C_Init(&hi2c1) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN I2C1_Init 2 */ + + /* USER CODE END I2C1_Init 2 */ + +} + +/** + * @brief I2C2 Initialization Function + * @param None + * @retval None + */ +static void MX_I2C2_Init(void) +{ + + /* USER CODE BEGIN I2C2_Init 0 */ + + /* USER CODE END I2C2_Init 0 */ + + /* USER CODE BEGIN I2C2_Init 1 */ + + /* USER CODE END I2C2_Init 1 */ + hi2c2.Instance = I2C2; + hi2c2.Init.ClockSpeed = 100000; + hi2c2.Init.DutyCycle = I2C_DUTYCYCLE_2; + hi2c2.Init.OwnAddress1 = 0; + hi2c2.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT; + hi2c2.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE; + hi2c2.Init.OwnAddress2 = 0; + hi2c2.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE; + hi2c2.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE; + if (HAL_I2C_Init(&hi2c2) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN I2C2_Init 2 */ + + /* USER CODE END I2C2_Init 2 */ + +} + +/** + * @brief SPI1 Initialization Function + * @param None + * @retval None + */ +static void MX_SPI1_Init(void) +{ + + /* USER CODE BEGIN SPI1_Init 0 */ + + /* USER CODE END SPI1_Init 0 */ + + /* USER CODE BEGIN SPI1_Init 1 */ + + /* USER CODE END SPI1_Init 1 */ + /* SPI1 parameter configuration*/ + hspi1.Instance = SPI1; + hspi1.Init.Mode = SPI_MODE_MASTER; + hspi1.Init.Direction = SPI_DIRECTION_2LINES; + hspi1.Init.DataSize = SPI_DATASIZE_8BIT; + hspi1.Init.CLKPolarity = SPI_POLARITY_LOW; + hspi1.Init.CLKPhase = SPI_PHASE_1EDGE; + hspi1.Init.NSS = SPI_NSS_SOFT; + hspi1.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2; + hspi1.Init.FirstBit = SPI_FIRSTBIT_MSB; + hspi1.Init.TIMode = SPI_TIMODE_DISABLE; + hspi1.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE; + hspi1.Init.CRCPolynomial = 10; + if (HAL_SPI_Init(&hspi1) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN SPI1_Init 2 */ + + /* USER CODE END SPI1_Init 2 */ + +} + +/** + * @brief SPI2 Initialization Function + * @param None + * @retval None + */ +static void MX_SPI2_Init(void) +{ + + /* USER CODE BEGIN SPI2_Init 0 */ + + /* USER CODE END SPI2_Init 0 */ + + /* USER CODE BEGIN SPI2_Init 1 */ + + /* USER CODE END SPI2_Init 1 */ + /* SPI2 parameter configuration*/ + hspi2.Instance = SPI2; + hspi2.Init.Mode = SPI_MODE_MASTER; + hspi2.Init.Direction = SPI_DIRECTION_2LINES; + hspi2.Init.DataSize = SPI_DATASIZE_8BIT; + hspi2.Init.CLKPolarity = SPI_POLARITY_LOW; + hspi2.Init.CLKPhase = SPI_PHASE_1EDGE; + hspi2.Init.NSS = SPI_NSS_SOFT; + hspi2.Init.BaudRatePrescaler = SPI_BAUDRATEPRESCALER_2; + hspi2.Init.FirstBit = SPI_FIRSTBIT_MSB; + hspi2.Init.TIMode = SPI_TIMODE_DISABLE; + hspi2.Init.CRCCalculation = SPI_CRCCALCULATION_DISABLE; + hspi2.Init.CRCPolynomial = 10; + if (HAL_SPI_Init(&hspi2) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN SPI2_Init 2 */ + + /* USER CODE END SPI2_Init 2 */ + +} + +/** + * @brief USART3 Initialization Function + * @param None + * @retval None + */ +static void MX_USART3_UART_Init(void) +{ + + /* USER CODE BEGIN USART3_Init 0 */ + + /* USER CODE END USART3_Init 0 */ + + /* USER CODE BEGIN USART3_Init 1 */ + + /* USER CODE END USART3_Init 1 */ + huart3.Instance = USART3; + huart3.Init.BaudRate = 115200; + huart3.Init.WordLength = UART_WORDLENGTH_8B; + huart3.Init.StopBits = UART_STOPBITS_1; + huart3.Init.Parity = UART_PARITY_NONE; + huart3.Init.Mode = UART_MODE_TX_RX; + huart3.Init.HwFlowCtl = UART_HWCONTROL_NONE; + huart3.Init.OverSampling = UART_OVERSAMPLING_16; + if (HAL_UART_Init(&huart3) != HAL_OK) + { + Error_Handler(); + } + /* USER CODE BEGIN USART3_Init 2 */ + + /* USER CODE END USART3_Init 2 */ + +} + +/** + * @brief GPIO Initialization Function + * @param None + * @retval None + */ +static void MX_GPIO_Init(void) +{ + GPIO_InitTypeDef GPIO_InitStruct = {0}; +/* USER CODE BEGIN MX_GPIO_Init_1 */ +/* USER CODE END MX_GPIO_Init_1 */ + + /* GPIO Ports Clock Enable */ + __HAL_RCC_GPIOH_CLK_ENABLE(); + __HAL_RCC_GPIOC_CLK_ENABLE(); + __HAL_RCC_GPIOA_CLK_ENABLE(); + __HAL_RCC_GPIOB_CLK_ENABLE(); + + /*Configure GPIO pin Output Level */ + HAL_GPIO_WritePin(GPIOC, GPIO_PIN_8|GPIO_PIN_9, GPIO_PIN_RESET); + + /*Configure GPIO pins : PC4 PC5 */ + GPIO_InitStruct.Pin = GPIO_PIN_4|GPIO_PIN_5; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + /*Configure GPIO pins : PB0 PB1 */ + GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + /*Configure GPIO pin : PB2 */ + GPIO_InitStruct.Pin = GPIO_PIN_2; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; + GPIO_InitStruct.Alternate = GPIO_AF15_EVENTOUT; + HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); + + /*Configure GPIO pins : PC8 PC9 */ + GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + /*Configure GPIO pin : PA9 */ + GPIO_InitStruct.Pin = GPIO_PIN_9; + GPIO_InitStruct.Mode = GPIO_MODE_INPUT; + GPIO_InitStruct.Pull = GPIO_NOPULL; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + + /*Configure GPIO pins : PA11 PA12 */ + GPIO_InitStruct.Pin = GPIO_PIN_11|GPIO_PIN_12; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS; + HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); + +/* USER CODE BEGIN MX_GPIO_Init_2 */ +/* USER CODE END MX_GPIO_Init_2 */ +} + +/* USER CODE BEGIN 4 */ + +/* USER CODE END 4 */ + +/* USER CODE BEGIN Header_StartDefaultTask */ +/** + * @brief Function implementing the defaultTask thread. + * @param argument: Not used + * @retval None + */ +/* USER CODE END Header_StartDefaultTask */ +void StartDefaultTask(void *argument) +{ + /* USER CODE BEGIN 5 */ + /* Infinite loop */ + uint8_t i = 0; + for(;;) + { + serial_print("TEST %i\r\n", i); + i++; + } + /* USER CODE END 5 */ +} + +/** + * @brief This function is executed in case of error occurrence. + * @retval None + */ +void Error_Handler(void) +{ + /* USER CODE BEGIN Error_Handler_Debug */ + /* User can add his own implementation to report the HAL error return state */ + __disable_irq(); + while (1) + { + } + /* USER CODE END Error_Handler_Debug */ +} + +#ifdef USE_FULL_ASSERT +/** + * @brief Reports the name of the source file and the source line number + * where the assert_param error has occurred. + * @param file: pointer to the source file name + * @param line: assert_param error line source number + * @retval None + */ +void assert_failed(uint8_t *file, uint32_t line) +{ + /* USER CODE BEGIN 6 */ + /* User can add his own implementation to report the file name and line number, + ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */ + /* USER CODE END 6 */ +} +#endif /* USE_FULL_ASSERT */ diff --git a/Core/Src/serial_monitor.c b/Core/Src/serial_monitor.c new file mode 100644 index 00000000..a2aff65f --- /dev/null +++ b/Core/Src/serial_monitor.c @@ -0,0 +1,53 @@ +#include "serial_monitor.h" +#include +#include +#include + +#define PRINTF_QUEUE_SIZE 16 /* Strings */ +#define PRINTF_BUFFER_LEN 128 /* Characters */ + +osMessageQueueId_t printf_queue; +osThreadId_t serial_monitor_handle; +const osThreadAttr_t serial_monitor_attributes; + +/* + * Referenced https://github.com/esp8266/Arduino/blob/master/cores/esp8266/Print.cpp + * Preformat string then put into a buffer + */ +int serial_print(const char* format, ...) +{ + va_list arg; + char temp[PRINTF_BUFFER_LEN]; + size_t len; + char* buffer = temp; + + /* Format Variadic Args into string */ + va_start(arg, format); + len = vsnprintf(temp, PRINTF_BUFFER_LEN, format, arg); + va_end(arg); + + /* Check to make sure we don't overflow buffer */ + if (len > PRINTF_BUFFER_LEN - 1) + return -1; + + osMessageQueuePut(printf_queue, &buffer, 0U, 0U); + return 0; +} + +void vSerialMonitor(void* pv_params) +{ + char* message; + osStatus_t status; + + printf_queue = osMessageQueueNew(PRINTF_QUEUE_SIZE, sizeof(char*), NULL); + + for (;;) { + /* Wait until new printf message comes into queue */ + status = osMessageQueueGet(printf_queue, &message, NULL, 0U); + if (status != osOK) { + // TODO: Trigger fault ? + } else { + printf(message); + } + } +} diff --git a/Core/Src/stm32f4xx_hal_msp.c b/Core/Src/stm32f4xx_hal_msp.c index 1a271d7a..eb4c7be0 100644 --- a/Core/Src/stm32f4xx_hal_msp.c +++ b/Core/Src/stm32f4xx_hal_msp.c @@ -444,6 +444,71 @@ void HAL_SPI_MspDeInit(SPI_HandleTypeDef* hspi) } +/** +* @brief UART MSP Initialization +* This function configures the hardware resources used in this example +* @param huart: UART handle pointer +* @retval None +*/ +void HAL_UART_MspInit(UART_HandleTypeDef* huart) +{ + GPIO_InitTypeDef GPIO_InitStruct = {0}; + if(huart->Instance==USART3) + { + /* USER CODE BEGIN USART3_MspInit 0 */ + + /* USER CODE END USART3_MspInit 0 */ + /* Peripheral clock enable */ + __HAL_RCC_USART3_CLK_ENABLE(); + + __HAL_RCC_GPIOC_CLK_ENABLE(); + /**USART3 GPIO Configuration + PC10 ------> USART3_TX + PC11 ------> USART3_RX + */ + GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11; + GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; + GPIO_InitStruct.Pull = GPIO_NOPULL; + GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; + GPIO_InitStruct.Alternate = GPIO_AF7_USART3; + HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); + + /* USER CODE BEGIN USART3_MspInit 1 */ + + /* USER CODE END USART3_MspInit 1 */ + } + +} + +/** +* @brief UART MSP De-Initialization +* This function freeze the hardware resources used in this example +* @param huart: UART handle pointer +* @retval None +*/ +void HAL_UART_MspDeInit(UART_HandleTypeDef* huart) +{ + if(huart->Instance==USART3) + { + /* USER CODE BEGIN USART3_MspDeInit 0 */ + + /* USER CODE END USART3_MspDeInit 0 */ + /* Peripheral clock disable */ + __HAL_RCC_USART3_CLK_DISABLE(); + + /**USART3 GPIO Configuration + PC10 ------> USART3_TX + PC11 ------> USART3_RX + */ + HAL_GPIO_DeInit(GPIOC, GPIO_PIN_10|GPIO_PIN_11); + + /* USER CODE BEGIN USART3_MspDeInit 1 */ + + /* USER CODE END USART3_MspDeInit 1 */ + } + +} + /* USER CODE BEGIN 1 */ /* USER CODE END 1 */ diff --git a/Dockerfile b/Dockerfile index d6f08497..0e52a12d 100644 --- a/Dockerfile +++ b/Dockerfile @@ -15,7 +15,8 @@ RUN apt-get install -y \ gdb-multiarch \ minicom \ vim \ - clang-format + clang-format \ + tmux RUN wget https://builds.renode.io/renode-1.14.0+20231003gitf86ac3cf.linux-portable.tar.gz RUN mkdir renode_portable && tar -xvf renode-*.linux-portable.tar.gz -C renode_portable --strip-components=1 diff --git a/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_uart.h b/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_uart.h new file mode 100644 index 00000000..543ebccb --- /dev/null +++ b/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_hal_uart.h @@ -0,0 +1,884 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_uart.h + * @author MCD Application Team + * @brief Header file of UART HAL module. + ****************************************************************************** + * @attention + * + * Copyright (c) 2016 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_HAL_UART_H +#define __STM32F4xx_HAL_UART_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal_def.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @addtogroup UART + * @{ + */ + +/* Exported types ------------------------------------------------------------*/ +/** @defgroup UART_Exported_Types UART Exported Types + * @{ + */ + +/** + * @brief UART Init Structure definition + */ +typedef struct +{ + uint32_t BaudRate; /*!< This member configures the UART communication baud rate. + The baud rate is computed using the following formula: + - IntegerDivider = ((PCLKx) / (8 * (OVR8+1) * (huart->Init.BaudRate))) + - FractionalDivider = ((IntegerDivider - ((uint32_t) IntegerDivider)) * 8 * (OVR8+1)) + 0.5 + Where OVR8 is the "oversampling by 8 mode" configuration bit in the CR1 register. */ + + uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame. + This parameter can be a value of @ref UART_Word_Length */ + + uint32_t StopBits; /*!< Specifies the number of stop bits transmitted. + This parameter can be a value of @ref UART_Stop_Bits */ + + uint32_t Parity; /*!< Specifies the parity mode. + This parameter can be a value of @ref UART_Parity + @note When parity is enabled, the computed parity is inserted + at the MSB position of the transmitted data (9th bit when + the word length is set to 9 data bits; 8th bit when the + word length is set to 8 data bits). */ + + uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled. + This parameter can be a value of @ref UART_Mode */ + + uint32_t HwFlowCtl; /*!< Specifies whether the hardware flow control mode is enabled or disabled. + This parameter can be a value of @ref UART_Hardware_Flow_Control */ + + uint32_t OverSampling; /*!< Specifies whether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to fPCLK/8). + This parameter can be a value of @ref UART_Over_Sampling */ +} UART_InitTypeDef; + +/** + * @brief HAL UART State structures definition + * @note HAL UART State value is a combination of 2 different substates: gState and RxState. + * - gState contains UART state information related to global Handle management + * and also information related to Tx operations. + * gState value coding follow below described bitmap : + * b7-b6 Error information + * 00 : No Error + * 01 : (Not Used) + * 10 : Timeout + * 11 : Error + * b5 Peripheral initialization status + * 0 : Reset (Peripheral not initialized) + * 1 : Init done (Peripheral initialized. HAL UART Init function already called) + * b4-b3 (not used) + * xx : Should be set to 00 + * b2 Intrinsic process state + * 0 : Ready + * 1 : Busy (Peripheral busy with some configuration or internal operations) + * b1 (not used) + * x : Should be set to 0 + * b0 Tx state + * 0 : Ready (no Tx operation ongoing) + * 1 : Busy (Tx operation ongoing) + * - RxState contains information related to Rx operations. + * RxState value coding follow below described bitmap : + * b7-b6 (not used) + * xx : Should be set to 00 + * b5 Peripheral initialization status + * 0 : Reset (Peripheral not initialized) + * 1 : Init done (Peripheral initialized) + * b4-b2 (not used) + * xxx : Should be set to 000 + * b1 Rx state + * 0 : Ready (no Rx operation ongoing) + * 1 : Busy (Rx operation ongoing) + * b0 (not used) + * x : Should be set to 0. + */ +typedef enum +{ + HAL_UART_STATE_RESET = 0x00U, /*!< Peripheral is not yet Initialized + Value is allowed for gState and RxState */ + HAL_UART_STATE_READY = 0x20U, /*!< Peripheral Initialized and ready for use + Value is allowed for gState and RxState */ + HAL_UART_STATE_BUSY = 0x24U, /*!< an internal process is ongoing + Value is allowed for gState only */ + HAL_UART_STATE_BUSY_TX = 0x21U, /*!< Data Transmission process is ongoing + Value is allowed for gState only */ + HAL_UART_STATE_BUSY_RX = 0x22U, /*!< Data Reception process is ongoing + Value is allowed for RxState only */ + HAL_UART_STATE_BUSY_TX_RX = 0x23U, /*!< Data Transmission and Reception process is ongoing + Not to be used for neither gState nor RxState. + Value is result of combination (Or) between gState and RxState values */ + HAL_UART_STATE_TIMEOUT = 0xA0U, /*!< Timeout state + Value is allowed for gState only */ + HAL_UART_STATE_ERROR = 0xE0U /*!< Error + Value is allowed for gState only */ +} HAL_UART_StateTypeDef; + +/** + * @brief HAL UART Reception type definition + * @note HAL UART Reception type value aims to identify which type of Reception is ongoing. + * It is expected to admit following values : + * HAL_UART_RECEPTION_STANDARD = 0x00U, + * HAL_UART_RECEPTION_TOIDLE = 0x01U, + */ +typedef uint32_t HAL_UART_RxTypeTypeDef; + +/** + * @brief UART handle Structure definition + */ +typedef struct __UART_HandleTypeDef +{ + USART_TypeDef *Instance; /*!< UART registers base address */ + + UART_InitTypeDef Init; /*!< UART communication parameters */ + + const uint8_t *pTxBuffPtr; /*!< Pointer to UART Tx transfer Buffer */ + + uint16_t TxXferSize; /*!< UART Tx Transfer size */ + + __IO uint16_t TxXferCount; /*!< UART Tx Transfer Counter */ + + uint8_t *pRxBuffPtr; /*!< Pointer to UART Rx transfer Buffer */ + + uint16_t RxXferSize; /*!< UART Rx Transfer size */ + + __IO uint16_t RxXferCount; /*!< UART Rx Transfer Counter */ + + __IO HAL_UART_RxTypeTypeDef ReceptionType; /*!< Type of ongoing reception */ + + DMA_HandleTypeDef *hdmatx; /*!< UART Tx DMA Handle parameters */ + + DMA_HandleTypeDef *hdmarx; /*!< UART Rx DMA Handle parameters */ + + HAL_LockTypeDef Lock; /*!< Locking object */ + + __IO HAL_UART_StateTypeDef gState; /*!< UART state information related to global Handle management + and also related to Tx operations. + This parameter can be a value of @ref HAL_UART_StateTypeDef */ + + __IO HAL_UART_StateTypeDef RxState; /*!< UART state information related to Rx operations. + This parameter can be a value of @ref HAL_UART_StateTypeDef */ + + __IO uint32_t ErrorCode; /*!< UART Error code */ + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + void (* TxHalfCpltCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Tx Half Complete Callback */ + void (* TxCpltCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Tx Complete Callback */ + void (* RxHalfCpltCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Rx Half Complete Callback */ + void (* RxCpltCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Rx Complete Callback */ + void (* ErrorCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Error Callback */ + void (* AbortCpltCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Abort Complete Callback */ + void (* AbortTransmitCpltCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Abort Transmit Complete Callback */ + void (* AbortReceiveCpltCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Abort Receive Complete Callback */ + void (* WakeupCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Wakeup Callback */ + void (* RxEventCallback)(struct __UART_HandleTypeDef *huart, uint16_t Pos); /*!< UART Reception Event Callback */ + + void (* MspInitCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Msp Init callback */ + void (* MspDeInitCallback)(struct __UART_HandleTypeDef *huart); /*!< UART Msp DeInit callback */ +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + +} UART_HandleTypeDef; + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) +/** + * @brief HAL UART Callback ID enumeration definition + */ +typedef enum +{ + HAL_UART_TX_HALFCOMPLETE_CB_ID = 0x00U, /*!< UART Tx Half Complete Callback ID */ + HAL_UART_TX_COMPLETE_CB_ID = 0x01U, /*!< UART Tx Complete Callback ID */ + HAL_UART_RX_HALFCOMPLETE_CB_ID = 0x02U, /*!< UART Rx Half Complete Callback ID */ + HAL_UART_RX_COMPLETE_CB_ID = 0x03U, /*!< UART Rx Complete Callback ID */ + HAL_UART_ERROR_CB_ID = 0x04U, /*!< UART Error Callback ID */ + HAL_UART_ABORT_COMPLETE_CB_ID = 0x05U, /*!< UART Abort Complete Callback ID */ + HAL_UART_ABORT_TRANSMIT_COMPLETE_CB_ID = 0x06U, /*!< UART Abort Transmit Complete Callback ID */ + HAL_UART_ABORT_RECEIVE_COMPLETE_CB_ID = 0x07U, /*!< UART Abort Receive Complete Callback ID */ + HAL_UART_WAKEUP_CB_ID = 0x08U, /*!< UART Wakeup Callback ID */ + + HAL_UART_MSPINIT_CB_ID = 0x0BU, /*!< UART MspInit callback ID */ + HAL_UART_MSPDEINIT_CB_ID = 0x0CU /*!< UART MspDeInit callback ID */ + +} HAL_UART_CallbackIDTypeDef; + +/** + * @brief HAL UART Callback pointer definition + */ +typedef void (*pUART_CallbackTypeDef)(UART_HandleTypeDef *huart); /*!< pointer to an UART callback function */ +typedef void (*pUART_RxEventCallbackTypeDef)(struct __UART_HandleTypeDef *huart, uint16_t Pos); /*!< pointer to a UART Rx Event specific callback function */ + +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + +/** + * @} + */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup UART_Exported_Constants UART Exported Constants + * @{ + */ + +/** @defgroup UART_Error_Code UART Error Code + * @{ + */ +#define HAL_UART_ERROR_NONE 0x00000000U /*!< No error */ +#define HAL_UART_ERROR_PE 0x00000001U /*!< Parity error */ +#define HAL_UART_ERROR_NE 0x00000002U /*!< Noise error */ +#define HAL_UART_ERROR_FE 0x00000004U /*!< Frame error */ +#define HAL_UART_ERROR_ORE 0x00000008U /*!< Overrun error */ +#define HAL_UART_ERROR_DMA 0x00000010U /*!< DMA transfer error */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) +#define HAL_UART_ERROR_INVALID_CALLBACK 0x00000020U /*!< Invalid Callback error */ +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +/** + * @} + */ + +/** @defgroup UART_Word_Length UART Word Length + * @{ + */ +#define UART_WORDLENGTH_8B 0x00000000U +#define UART_WORDLENGTH_9B ((uint32_t)USART_CR1_M) +/** + * @} + */ + +/** @defgroup UART_Stop_Bits UART Number of Stop Bits + * @{ + */ +#define UART_STOPBITS_1 0x00000000U +#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1) +/** + * @} + */ + +/** @defgroup UART_Parity UART Parity + * @{ + */ +#define UART_PARITY_NONE 0x00000000U +#define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE) +#define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS)) +/** + * @} + */ + +/** @defgroup UART_Hardware_Flow_Control UART Hardware Flow Control + * @{ + */ +#define UART_HWCONTROL_NONE 0x00000000U +#define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE) +#define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE) +#define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE)) +/** + * @} + */ + +/** @defgroup UART_Mode UART Transfer Mode + * @{ + */ +#define UART_MODE_RX ((uint32_t)USART_CR1_RE) +#define UART_MODE_TX ((uint32_t)USART_CR1_TE) +#define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE | USART_CR1_RE)) +/** + * @} + */ + +/** @defgroup UART_State UART State + * @{ + */ +#define UART_STATE_DISABLE 0x00000000U +#define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE) +/** + * @} + */ + +/** @defgroup UART_Over_Sampling UART Over Sampling + * @{ + */ +#define UART_OVERSAMPLING_16 0x00000000U +#define UART_OVERSAMPLING_8 ((uint32_t)USART_CR1_OVER8) +/** + * @} + */ + +/** @defgroup UART_LIN_Break_Detection_Length UART LIN Break Detection Length + * @{ + */ +#define UART_LINBREAKDETECTLENGTH_10B 0x00000000U +#define UART_LINBREAKDETECTLENGTH_11B ((uint32_t)USART_CR2_LBDL) +/** + * @} + */ + +/** @defgroup UART_WakeUp_functions UART Wakeup Functions + * @{ + */ +#define UART_WAKEUPMETHOD_IDLELINE 0x00000000U +#define UART_WAKEUPMETHOD_ADDRESSMARK ((uint32_t)USART_CR1_WAKE) +/** + * @} + */ + +/** @defgroup UART_Flags UART FLags + * Elements values convention: 0xXXXX + * - 0xXXXX : Flag mask in the SR register + * @{ + */ +#define UART_FLAG_CTS ((uint32_t)USART_SR_CTS) +#define UART_FLAG_LBD ((uint32_t)USART_SR_LBD) +#define UART_FLAG_TXE ((uint32_t)USART_SR_TXE) +#define UART_FLAG_TC ((uint32_t)USART_SR_TC) +#define UART_FLAG_RXNE ((uint32_t)USART_SR_RXNE) +#define UART_FLAG_IDLE ((uint32_t)USART_SR_IDLE) +#define UART_FLAG_ORE ((uint32_t)USART_SR_ORE) +#define UART_FLAG_NE ((uint32_t)USART_SR_NE) +#define UART_FLAG_FE ((uint32_t)USART_SR_FE) +#define UART_FLAG_PE ((uint32_t)USART_SR_PE) +/** + * @} + */ + +/** @defgroup UART_Interrupt_definition UART Interrupt Definitions + * Elements values convention: 0xY000XXXX + * - XXXX : Interrupt mask (16 bits) in the Y register + * - Y : Interrupt source register (2bits) + * - 0001: CR1 register + * - 0010: CR2 register + * - 0011: CR3 register + * @{ + */ + +#define UART_IT_PE ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_PEIE)) +#define UART_IT_TXE ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_TXEIE)) +#define UART_IT_TC ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_TCIE)) +#define UART_IT_RXNE ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_RXNEIE)) +#define UART_IT_IDLE ((uint32_t)(UART_CR1_REG_INDEX << 28U | USART_CR1_IDLEIE)) + +#define UART_IT_LBD ((uint32_t)(UART_CR2_REG_INDEX << 28U | USART_CR2_LBDIE)) + +#define UART_IT_CTS ((uint32_t)(UART_CR3_REG_INDEX << 28U | USART_CR3_CTSIE)) +#define UART_IT_ERR ((uint32_t)(UART_CR3_REG_INDEX << 28U | USART_CR3_EIE)) +/** + * @} + */ + +/** @defgroup UART_RECEPTION_TYPE_Values UART Reception type values + * @{ + */ +#define HAL_UART_RECEPTION_STANDARD (0x00000000U) /*!< Standard reception */ +#define HAL_UART_RECEPTION_TOIDLE (0x00000001U) /*!< Reception till completion or IDLE event */ +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup UART_Exported_Macros UART Exported Macros + * @{ + */ + +/** @brief Reset UART handle gstate & RxState + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) +#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__) do{ \ + (__HANDLE__)->gState = HAL_UART_STATE_RESET; \ + (__HANDLE__)->RxState = HAL_UART_STATE_RESET; \ + (__HANDLE__)->MspInitCallback = NULL; \ + (__HANDLE__)->MspDeInitCallback = NULL; \ + } while(0U) +#else +#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__) do{ \ + (__HANDLE__)->gState = HAL_UART_STATE_RESET; \ + (__HANDLE__)->RxState = HAL_UART_STATE_RESET; \ + } while(0U) +#endif /*USE_HAL_UART_REGISTER_CALLBACKS */ + +/** @brief Flushes the UART DR register + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + */ +#define __HAL_UART_FLUSH_DRREGISTER(__HANDLE__) ((__HANDLE__)->Instance->DR) + +/** @brief Checks whether the specified UART flag is set or not. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __FLAG__ specifies the flag to check. + * This parameter can be one of the following values: + * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5) + * @arg UART_FLAG_LBD: LIN Break detection flag + * @arg UART_FLAG_TXE: Transmit data register empty flag + * @arg UART_FLAG_TC: Transmission Complete flag + * @arg UART_FLAG_RXNE: Receive data register not empty flag + * @arg UART_FLAG_IDLE: Idle Line detection flag + * @arg UART_FLAG_ORE: Overrun Error flag + * @arg UART_FLAG_NE: Noise Error flag + * @arg UART_FLAG_FE: Framing Error flag + * @arg UART_FLAG_PE: Parity Error flag + * @retval The new state of __FLAG__ (TRUE or FALSE). + */ +#define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->SR & (__FLAG__)) == (__FLAG__)) + +/** @brief Clears the specified UART pending flag. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __FLAG__ specifies the flag to check. + * This parameter can be any combination of the following values: + * @arg UART_FLAG_CTS: CTS Change flag (not available for UART4 and UART5). + * @arg UART_FLAG_LBD: LIN Break detection flag. + * @arg UART_FLAG_TC: Transmission Complete flag. + * @arg UART_FLAG_RXNE: Receive data register not empty flag. + * + * @note PE (Parity error), FE (Framing error), NE (Noise error), ORE (Overrun + * error) and IDLE (Idle line detected) flags are cleared by software + * sequence: a read operation to USART_SR register followed by a read + * operation to USART_DR register. + * @note RXNE flag can be also cleared by a read to the USART_DR register. + * @note TC flag can be also cleared by software sequence: a read operation to + * USART_SR register followed by a write operation to USART_DR register. + * @note TXE flag is cleared only by a write to the USART_DR register. + * + * @retval None + */ +#define __HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->SR = ~(__FLAG__)) + +/** @brief Clears the UART PE pending flag. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_PEFLAG(__HANDLE__) \ + do{ \ + __IO uint32_t tmpreg = 0x00U; \ + tmpreg = (__HANDLE__)->Instance->SR; \ + tmpreg = (__HANDLE__)->Instance->DR; \ + UNUSED(tmpreg); \ + } while(0U) + +/** @brief Clears the UART FE pending flag. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_FEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clears the UART NE pending flag. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_NEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clears the UART ORE pending flag. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_OREFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Clears the UART IDLE pending flag. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @retval None + */ +#define __HAL_UART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_UART_CLEAR_PEFLAG(__HANDLE__) + +/** @brief Enable the specified UART interrupt. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __INTERRUPT__ specifies the UART interrupt source to enable. + * This parameter can be one of the following values: + * @arg UART_IT_CTS: CTS change interrupt + * @arg UART_IT_LBD: LIN Break detection interrupt + * @arg UART_IT_TXE: Transmit Data Register empty interrupt + * @arg UART_IT_TC: Transmission complete interrupt + * @arg UART_IT_RXNE: Receive Data register not empty interrupt + * @arg UART_IT_IDLE: Idle line detection interrupt + * @arg UART_IT_PE: Parity Error interrupt + * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error) + * @retval None + */ +#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28U) == UART_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 |= ((__INTERRUPT__) & UART_IT_MASK)): \ + (((__INTERRUPT__) >> 28U) == UART_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 |= ((__INTERRUPT__) & UART_IT_MASK)): \ + ((__HANDLE__)->Instance->CR3 |= ((__INTERRUPT__) & UART_IT_MASK))) + +/** @brief Disable the specified UART interrupt. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __INTERRUPT__ specifies the UART interrupt source to disable. + * This parameter can be one of the following values: + * @arg UART_IT_CTS: CTS change interrupt + * @arg UART_IT_LBD: LIN Break detection interrupt + * @arg UART_IT_TXE: Transmit Data Register empty interrupt + * @arg UART_IT_TC: Transmission complete interrupt + * @arg UART_IT_RXNE: Receive Data register not empty interrupt + * @arg UART_IT_IDLE: Idle line detection interrupt + * @arg UART_IT_PE: Parity Error interrupt + * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error) + * @retval None + */ +#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) ((((__INTERRUPT__) >> 28U) == UART_CR1_REG_INDEX)? ((__HANDLE__)->Instance->CR1 &= ~((__INTERRUPT__) & UART_IT_MASK)): \ + (((__INTERRUPT__) >> 28U) == UART_CR2_REG_INDEX)? ((__HANDLE__)->Instance->CR2 &= ~((__INTERRUPT__) & UART_IT_MASK)): \ + ((__HANDLE__)->Instance->CR3 &= ~ ((__INTERRUPT__) & UART_IT_MASK))) + +/** @brief Checks whether the specified UART interrupt source is enabled or not. + * @param __HANDLE__ specifies the UART Handle. + * UART Handle selects the USARTx or UARTy peripheral + * (USART,UART availability and x,y values depending on device). + * @param __IT__ specifies the UART interrupt source to check. + * This parameter can be one of the following values: + * @arg UART_IT_CTS: CTS change interrupt (not available for UART4 and UART5) + * @arg UART_IT_LBD: LIN Break detection interrupt + * @arg UART_IT_TXE: Transmit Data Register empty interrupt + * @arg UART_IT_TC: Transmission complete interrupt + * @arg UART_IT_RXNE: Receive Data register not empty interrupt + * @arg UART_IT_IDLE: Idle line detection interrupt + * @arg UART_IT_ERR: Error interrupt + * @retval The new state of __IT__ (TRUE or FALSE). + */ +#define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) (((((__IT__) >> 28U) == UART_CR1_REG_INDEX)? (__HANDLE__)->Instance->CR1:(((((uint32_t)(__IT__)) >> 28U) == UART_CR2_REG_INDEX)? \ + (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & (((uint32_t)(__IT__)) & UART_IT_MASK)) + +/** @brief Enable CTS flow control + * @note This macro allows to enable CTS hardware flow control for a given UART instance, + * without need to call HAL_UART_Init() function. + * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. + * @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need + * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : + * - UART instance should have already been initialised (through call of HAL_UART_Init() ) + * - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__)) + * and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)). + * @param __HANDLE__ specifies the UART Handle. + * The Handle Instance can be any USARTx (supporting the HW Flow control feature). + * It is used to select the USART peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__) \ + do{ \ + ATOMIC_SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \ + (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE; \ + } while(0U) + +/** @brief Disable CTS flow control + * @note This macro allows to disable CTS hardware flow control for a given UART instance, + * without need to call HAL_UART_Init() function. + * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. + * @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need + * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : + * - UART instance should have already been initialised (through call of HAL_UART_Init() ) + * - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__)) + * and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)). + * @param __HANDLE__ specifies the UART Handle. + * The Handle Instance can be any USARTx (supporting the HW Flow control feature). + * It is used to select the USART peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__) \ + do{ \ + ATOMIC_CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \ + (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE); \ + } while(0U) + +/** @brief Enable RTS flow control + * This macro allows to enable RTS hardware flow control for a given UART instance, + * without need to call HAL_UART_Init() function. + * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. + * @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need + * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : + * - UART instance should have already been initialised (through call of HAL_UART_Init() ) + * - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__)) + * and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)). + * @param __HANDLE__ specifies the UART Handle. + * The Handle Instance can be any USARTx (supporting the HW Flow control feature). + * It is used to select the USART peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__) \ + do{ \ + ATOMIC_SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \ + (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE; \ + } while(0U) + +/** @brief Disable RTS flow control + * This macro allows to disable RTS hardware flow control for a given UART instance, + * without need to call HAL_UART_Init() function. + * As involving direct access to UART registers, usage of this macro should be fully endorsed by user. + * @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need + * for USART instance Deinit/Init, following conditions for macro call should be fulfilled : + * - UART instance should have already been initialised (through call of HAL_UART_Init() ) + * - macro could only be called when corresponding UART instance is disabled (i.e __HAL_UART_DISABLE(__HANDLE__)) + * and should be followed by an Enable macro (i.e __HAL_UART_ENABLE(__HANDLE__)). + * @param __HANDLE__ specifies the UART Handle. + * The Handle Instance can be any USARTx (supporting the HW Flow control feature). + * It is used to select the USART peripheral (USART availability and x value depending on device). + * @retval None + */ +#define __HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__) \ + do{ \ + ATOMIC_CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\ + (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE); \ + } while(0U) + +/** @brief Macro to enable the UART's one bit sample method + * @param __HANDLE__ specifies the UART Handle. + * @retval None + */ +#define __HAL_UART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT) + +/** @brief Macro to disable the UART's one bit sample method + * @param __HANDLE__ specifies the UART Handle. + * @retval None + */ +#define __HAL_UART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3\ + &= (uint16_t)~((uint16_t)USART_CR3_ONEBIT)) + +/** @brief Enable UART + * @param __HANDLE__ specifies the UART Handle. + * @retval None + */ +#define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE) + +/** @brief Disable UART + * @param __HANDLE__ specifies the UART Handle. + * @retval None + */ +#define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE) +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ +/** @addtogroup UART_Exported_Functions + * @{ + */ + +/** @addtogroup UART_Exported_Functions_Group1 Initialization and de-initialization functions + * @{ + */ + +/* Initialization/de-initialization functions **********************************/ +HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength); +HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod); +HAL_StatusTypeDef HAL_UART_DeInit(UART_HandleTypeDef *huart); +void HAL_UART_MspInit(UART_HandleTypeDef *huart); +void HAL_UART_MspDeInit(UART_HandleTypeDef *huart); + +/* Callbacks Register/UnRegister functions ***********************************/ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) +HAL_StatusTypeDef HAL_UART_RegisterCallback(UART_HandleTypeDef *huart, HAL_UART_CallbackIDTypeDef CallbackID, + pUART_CallbackTypeDef pCallback); +HAL_StatusTypeDef HAL_UART_UnRegisterCallback(UART_HandleTypeDef *huart, HAL_UART_CallbackIDTypeDef CallbackID); + +HAL_StatusTypeDef HAL_UART_RegisterRxEventCallback(UART_HandleTypeDef *huart, pUART_RxEventCallbackTypeDef pCallback); +HAL_StatusTypeDef HAL_UART_UnRegisterRxEventCallback(UART_HandleTypeDef *huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + +/** + * @} + */ + +/** @addtogroup UART_Exported_Functions_Group2 IO operation functions + * @{ + */ + +/* IO operation functions *******************************************************/ +HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, const uint8_t *pData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout); +HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, const uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, const uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart); + +HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint16_t *RxLen, + uint32_t Timeout); +HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); + +/* Transfer Abort functions */ +HAL_StatusTypeDef HAL_UART_Abort(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_AbortTransmit(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_AbortReceive(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_Abort_IT(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_AbortTransmit_IT(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_UART_AbortReceive_IT(UART_HandleTypeDef *huart); + +void HAL_UART_IRQHandler(UART_HandleTypeDef *huart); +void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart); +void HAL_UART_AbortCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_AbortTransmitCpltCallback(UART_HandleTypeDef *huart); +void HAL_UART_AbortReceiveCpltCallback(UART_HandleTypeDef *huart); + +void HAL_UARTEx_RxEventCallback(UART_HandleTypeDef *huart, uint16_t Size); + +/** + * @} + */ + +/** @addtogroup UART_Exported_Functions_Group3 + * @{ + */ +/* Peripheral Control functions ************************************************/ +HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart); +HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart); +/** + * @} + */ + +/** @addtogroup UART_Exported_Functions_Group4 + * @{ + */ +/* Peripheral State functions **************************************************/ +HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart); +uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart); +/** + * @} + */ + +/** + * @} + */ +/* Private types -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private constants ---------------------------------------------------------*/ +/** @defgroup UART_Private_Constants UART Private Constants + * @{ + */ +/** @brief UART interruptions flag mask + * + */ +#define UART_IT_MASK 0x0000FFFFU + +#define UART_CR1_REG_INDEX 1U +#define UART_CR2_REG_INDEX 2U +#define UART_CR3_REG_INDEX 3U +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +/** @defgroup UART_Private_Macros UART Private Macros + * @{ + */ +#define IS_UART_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B) || \ + ((LENGTH) == UART_WORDLENGTH_9B)) +#define IS_UART_LIN_WORD_LENGTH(LENGTH) (((LENGTH) == UART_WORDLENGTH_8B)) +#define IS_UART_STOPBITS(STOPBITS) (((STOPBITS) == UART_STOPBITS_1) || \ + ((STOPBITS) == UART_STOPBITS_2)) +#define IS_UART_PARITY(PARITY) (((PARITY) == UART_PARITY_NONE) || \ + ((PARITY) == UART_PARITY_EVEN) || \ + ((PARITY) == UART_PARITY_ODD)) +#define IS_UART_HARDWARE_FLOW_CONTROL(CONTROL)\ + (((CONTROL) == UART_HWCONTROL_NONE) || \ + ((CONTROL) == UART_HWCONTROL_RTS) || \ + ((CONTROL) == UART_HWCONTROL_CTS) || \ + ((CONTROL) == UART_HWCONTROL_RTS_CTS)) +#define IS_UART_MODE(MODE) ((((MODE) & 0x0000FFF3U) == 0x00U) && ((MODE) != 0x00U)) +#define IS_UART_STATE(STATE) (((STATE) == UART_STATE_DISABLE) || \ + ((STATE) == UART_STATE_ENABLE)) +#define IS_UART_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16) || \ + ((SAMPLING) == UART_OVERSAMPLING_8)) +#define IS_UART_LIN_OVERSAMPLING(SAMPLING) (((SAMPLING) == UART_OVERSAMPLING_16)) +#define IS_UART_LIN_BREAK_DETECT_LENGTH(LENGTH) (((LENGTH) == UART_LINBREAKDETECTLENGTH_10B) || \ + ((LENGTH) == UART_LINBREAKDETECTLENGTH_11B)) +#define IS_UART_WAKEUPMETHOD(WAKEUP) (((WAKEUP) == UART_WAKEUPMETHOD_IDLELINE) || \ + ((WAKEUP) == UART_WAKEUPMETHOD_ADDRESSMARK)) +#define IS_UART_BAUDRATE(BAUDRATE) ((BAUDRATE) <= 10500000U) +#define IS_UART_ADDRESS(ADDRESS) ((ADDRESS) <= 0x0FU) + +#define UART_DIV_SAMPLING16(_PCLK_, _BAUD_) ((uint32_t)((((uint64_t)(_PCLK_))*25U)/(4U*((uint64_t)(_BAUD_))))) +#define UART_DIVMANT_SAMPLING16(_PCLK_, _BAUD_) (UART_DIV_SAMPLING16((_PCLK_), (_BAUD_))/100U) +#define UART_DIVFRAQ_SAMPLING16(_PCLK_, _BAUD_) ((((UART_DIV_SAMPLING16((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) * 100U)) * 16U)\ + + 50U) / 100U) +/* UART BRR = mantissa + overflow + fraction + = (UART DIVMANT << 4) + (UART DIVFRAQ & 0xF0) + (UART DIVFRAQ & 0x0FU) */ +#define UART_BRR_SAMPLING16(_PCLK_, _BAUD_) ((UART_DIVMANT_SAMPLING16((_PCLK_), (_BAUD_)) << 4U) + \ + (UART_DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0xF0U) + \ + (UART_DIVFRAQ_SAMPLING16((_PCLK_), (_BAUD_)) & 0x0FU)) + +#define UART_DIV_SAMPLING8(_PCLK_, _BAUD_) ((uint32_t)((((uint64_t)(_PCLK_))*25U)/(2U*((uint64_t)(_BAUD_))))) +#define UART_DIVMANT_SAMPLING8(_PCLK_, _BAUD_) (UART_DIV_SAMPLING8((_PCLK_), (_BAUD_))/100U) +#define UART_DIVFRAQ_SAMPLING8(_PCLK_, _BAUD_) ((((UART_DIV_SAMPLING8((_PCLK_), (_BAUD_)) - (UART_DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) * 100U)) * 8U)\ + + 50U) / 100U) +/* UART BRR = mantissa + overflow + fraction + = (UART DIVMANT << 4) + ((UART DIVFRAQ & 0xF8) << 1) + (UART DIVFRAQ & 0x07U) */ +#define UART_BRR_SAMPLING8(_PCLK_, _BAUD_) ((UART_DIVMANT_SAMPLING8((_PCLK_), (_BAUD_)) << 4U) + \ + ((UART_DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0xF8U) << 1U) + \ + (UART_DIVFRAQ_SAMPLING8((_PCLK_), (_BAUD_)) & 0x07U)) + +/** + * @} + */ + +/* Private functions ---------------------------------------------------------*/ +/** @defgroup UART_Private_Functions UART Private Functions + * @{ + */ + +HAL_StatusTypeDef UART_Start_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); +HAL_StatusTypeDef UART_Start_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size); + +/** + * @} + */ + +/** + * @} + */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_HAL_UART_H */ + diff --git a/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_usart.h b/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_usart.h new file mode 100644 index 00000000..64f59b08 --- /dev/null +++ b/Drivers/STM32F4xx_HAL_Driver/Inc/stm32f4xx_ll_usart.h @@ -0,0 +1,2521 @@ +/** + ****************************************************************************** + * @file stm32f4xx_ll_usart.h + * @author MCD Application Team + * @brief Header file of USART LL module. + ****************************************************************************** + * @attention + * + * Copyright (c) 2016 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + */ + +/* Define to prevent recursive inclusion -------------------------------------*/ +#ifndef __STM32F4xx_LL_USART_H +#define __STM32F4xx_LL_USART_H + +#ifdef __cplusplus +extern "C" { +#endif + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx.h" + +/** @addtogroup STM32F4xx_LL_Driver + * @{ + */ + +#if defined (USART1) || defined (USART2) || defined (USART3) || defined (USART6) || defined (UART4) || defined (UART5) || defined (UART7) || defined (UART8) || defined (UART9) || defined (UART10) + +/** @defgroup USART_LL USART + * @{ + */ + +/* Private types -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ + +/* Private constants ---------------------------------------------------------*/ +/** @defgroup USART_LL_Private_Constants USART Private Constants + * @{ + */ + +/* Defines used for the bit position in the register and perform offsets*/ +#define USART_POSITION_GTPR_GT USART_GTPR_GT_Pos +/** + * @} + */ + +/* Private macros ------------------------------------------------------------*/ +#if defined(USE_FULL_LL_DRIVER) +/** @defgroup USART_LL_Private_Macros USART Private Macros + * @{ + */ +/** + * @} + */ +#endif /*USE_FULL_LL_DRIVER*/ + +/* Exported types ------------------------------------------------------------*/ +#if defined(USE_FULL_LL_DRIVER) +/** @defgroup USART_LL_ES_INIT USART Exported Init structures + * @{ + */ + +/** + * @brief LL USART Init Structure definition + */ +typedef struct +{ + uint32_t BaudRate; /*!< This field defines expected Usart communication baud rate. + + This feature can be modified afterwards using unitary function @ref LL_USART_SetBaudRate().*/ + + uint32_t DataWidth; /*!< Specifies the number of data bits transmitted or received in a frame. + This parameter can be a value of @ref USART_LL_EC_DATAWIDTH. + + This feature can be modified afterwards using unitary function @ref LL_USART_SetDataWidth().*/ + + uint32_t StopBits; /*!< Specifies the number of stop bits transmitted. + This parameter can be a value of @ref USART_LL_EC_STOPBITS. + + This feature can be modified afterwards using unitary function @ref LL_USART_SetStopBitsLength().*/ + + uint32_t Parity; /*!< Specifies the parity mode. + This parameter can be a value of @ref USART_LL_EC_PARITY. + + This feature can be modified afterwards using unitary function @ref LL_USART_SetParity().*/ + + uint32_t TransferDirection; /*!< Specifies whether the Receive and/or Transmit mode is enabled or disabled. + This parameter can be a value of @ref USART_LL_EC_DIRECTION. + + This feature can be modified afterwards using unitary function @ref LL_USART_SetTransferDirection().*/ + + uint32_t HardwareFlowControl; /*!< Specifies whether the hardware flow control mode is enabled or disabled. + This parameter can be a value of @ref USART_LL_EC_HWCONTROL. + + This feature can be modified afterwards using unitary function @ref LL_USART_SetHWFlowCtrl().*/ + + uint32_t OverSampling; /*!< Specifies whether USART oversampling mode is 16 or 8. + This parameter can be a value of @ref USART_LL_EC_OVERSAMPLING. + + This feature can be modified afterwards using unitary function @ref LL_USART_SetOverSampling().*/ + +} LL_USART_InitTypeDef; + +/** + * @brief LL USART Clock Init Structure definition + */ +typedef struct +{ + uint32_t ClockOutput; /*!< Specifies whether the USART clock is enabled or disabled. + This parameter can be a value of @ref USART_LL_EC_CLOCK. + + USART HW configuration can be modified afterwards using unitary functions + @ref LL_USART_EnableSCLKOutput() or @ref LL_USART_DisableSCLKOutput(). + For more details, refer to description of this function. */ + + uint32_t ClockPolarity; /*!< Specifies the steady state of the serial clock. + This parameter can be a value of @ref USART_LL_EC_POLARITY. + + USART HW configuration can be modified afterwards using unitary functions @ref LL_USART_SetClockPolarity(). + For more details, refer to description of this function. */ + + uint32_t ClockPhase; /*!< Specifies the clock transition on which the bit capture is made. + This parameter can be a value of @ref USART_LL_EC_PHASE. + + USART HW configuration can be modified afterwards using unitary functions @ref LL_USART_SetClockPhase(). + For more details, refer to description of this function. */ + + uint32_t LastBitClockPulse; /*!< Specifies whether the clock pulse corresponding to the last transmitted + data bit (MSB) has to be output on the SCLK pin in synchronous mode. + This parameter can be a value of @ref USART_LL_EC_LASTCLKPULSE. + + USART HW configuration can be modified afterwards using unitary functions @ref LL_USART_SetLastClkPulseOutput(). + For more details, refer to description of this function. */ + +} LL_USART_ClockInitTypeDef; + +/** + * @} + */ +#endif /* USE_FULL_LL_DRIVER */ + +/* Exported constants --------------------------------------------------------*/ +/** @defgroup USART_LL_Exported_Constants USART Exported Constants + * @{ + */ + +/** @defgroup USART_LL_EC_GET_FLAG Get Flags Defines + * @brief Flags defines which can be used with LL_USART_ReadReg function + * @{ + */ +#define LL_USART_SR_PE USART_SR_PE /*!< Parity error flag */ +#define LL_USART_SR_FE USART_SR_FE /*!< Framing error flag */ +#define LL_USART_SR_NE USART_SR_NE /*!< Noise detected flag */ +#define LL_USART_SR_ORE USART_SR_ORE /*!< Overrun error flag */ +#define LL_USART_SR_IDLE USART_SR_IDLE /*!< Idle line detected flag */ +#define LL_USART_SR_RXNE USART_SR_RXNE /*!< Read data register not empty flag */ +#define LL_USART_SR_TC USART_SR_TC /*!< Transmission complete flag */ +#define LL_USART_SR_TXE USART_SR_TXE /*!< Transmit data register empty flag */ +#define LL_USART_SR_LBD USART_SR_LBD /*!< LIN break detection flag */ +#define LL_USART_SR_CTS USART_SR_CTS /*!< CTS flag */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_IT IT Defines + * @brief IT defines which can be used with LL_USART_ReadReg and LL_USART_WriteReg functions + * @{ + */ +#define LL_USART_CR1_IDLEIE USART_CR1_IDLEIE /*!< IDLE interrupt enable */ +#define LL_USART_CR1_RXNEIE USART_CR1_RXNEIE /*!< Read data register not empty interrupt enable */ +#define LL_USART_CR1_TCIE USART_CR1_TCIE /*!< Transmission complete interrupt enable */ +#define LL_USART_CR1_TXEIE USART_CR1_TXEIE /*!< Transmit data register empty interrupt enable */ +#define LL_USART_CR1_PEIE USART_CR1_PEIE /*!< Parity error */ +#define LL_USART_CR2_LBDIE USART_CR2_LBDIE /*!< LIN break detection interrupt enable */ +#define LL_USART_CR3_EIE USART_CR3_EIE /*!< Error interrupt enable */ +#define LL_USART_CR3_CTSIE USART_CR3_CTSIE /*!< CTS interrupt enable */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_DIRECTION Communication Direction + * @{ + */ +#define LL_USART_DIRECTION_NONE 0x00000000U /*!< Transmitter and Receiver are disabled */ +#define LL_USART_DIRECTION_RX USART_CR1_RE /*!< Transmitter is disabled and Receiver is enabled */ +#define LL_USART_DIRECTION_TX USART_CR1_TE /*!< Transmitter is enabled and Receiver is disabled */ +#define LL_USART_DIRECTION_TX_RX (USART_CR1_TE |USART_CR1_RE) /*!< Transmitter and Receiver are enabled */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_PARITY Parity Control + * @{ + */ +#define LL_USART_PARITY_NONE 0x00000000U /*!< Parity control disabled */ +#define LL_USART_PARITY_EVEN USART_CR1_PCE /*!< Parity control enabled and Even Parity is selected */ +#define LL_USART_PARITY_ODD (USART_CR1_PCE | USART_CR1_PS) /*!< Parity control enabled and Odd Parity is selected */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_WAKEUP Wakeup + * @{ + */ +#define LL_USART_WAKEUP_IDLELINE 0x00000000U /*!< USART wake up from Mute mode on Idle Line */ +#define LL_USART_WAKEUP_ADDRESSMARK USART_CR1_WAKE /*!< USART wake up from Mute mode on Address Mark */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_DATAWIDTH Datawidth + * @{ + */ +#define LL_USART_DATAWIDTH_8B 0x00000000U /*!< 8 bits word length : Start bit, 8 data bits, n stop bits */ +#define LL_USART_DATAWIDTH_9B USART_CR1_M /*!< 9 bits word length : Start bit, 9 data bits, n stop bits */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_OVERSAMPLING Oversampling + * @{ + */ +#define LL_USART_OVERSAMPLING_16 0x00000000U /*!< Oversampling by 16 */ +#define LL_USART_OVERSAMPLING_8 USART_CR1_OVER8 /*!< Oversampling by 8 */ +/** + * @} + */ + +#if defined(USE_FULL_LL_DRIVER) +/** @defgroup USART_LL_EC_CLOCK Clock Signal + * @{ + */ + +#define LL_USART_CLOCK_DISABLE 0x00000000U /*!< Clock signal not provided */ +#define LL_USART_CLOCK_ENABLE USART_CR2_CLKEN /*!< Clock signal provided */ +/** + * @} + */ +#endif /*USE_FULL_LL_DRIVER*/ + +/** @defgroup USART_LL_EC_LASTCLKPULSE Last Clock Pulse + * @{ + */ +#define LL_USART_LASTCLKPULSE_NO_OUTPUT 0x00000000U /*!< The clock pulse of the last data bit is not output to the SCLK pin */ +#define LL_USART_LASTCLKPULSE_OUTPUT USART_CR2_LBCL /*!< The clock pulse of the last data bit is output to the SCLK pin */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_PHASE Clock Phase + * @{ + */ +#define LL_USART_PHASE_1EDGE 0x00000000U /*!< The first clock transition is the first data capture edge */ +#define LL_USART_PHASE_2EDGE USART_CR2_CPHA /*!< The second clock transition is the first data capture edge */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_POLARITY Clock Polarity + * @{ + */ +#define LL_USART_POLARITY_LOW 0x00000000U /*!< Steady low value on SCLK pin outside transmission window*/ +#define LL_USART_POLARITY_HIGH USART_CR2_CPOL /*!< Steady high value on SCLK pin outside transmission window */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_STOPBITS Stop Bits + * @{ + */ +#define LL_USART_STOPBITS_0_5 USART_CR2_STOP_0 /*!< 0.5 stop bit */ +#define LL_USART_STOPBITS_1 0x00000000U /*!< 1 stop bit */ +#define LL_USART_STOPBITS_1_5 (USART_CR2_STOP_0 | USART_CR2_STOP_1) /*!< 1.5 stop bits */ +#define LL_USART_STOPBITS_2 USART_CR2_STOP_1 /*!< 2 stop bits */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_HWCONTROL Hardware Control + * @{ + */ +#define LL_USART_HWCONTROL_NONE 0x00000000U /*!< CTS and RTS hardware flow control disabled */ +#define LL_USART_HWCONTROL_RTS USART_CR3_RTSE /*!< RTS output enabled, data is only requested when there is space in the receive buffer */ +#define LL_USART_HWCONTROL_CTS USART_CR3_CTSE /*!< CTS mode enabled, data is only transmitted when the nCTS input is asserted (tied to 0) */ +#define LL_USART_HWCONTROL_RTS_CTS (USART_CR3_RTSE | USART_CR3_CTSE) /*!< CTS and RTS hardware flow control enabled */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_IRDA_POWER IrDA Power + * @{ + */ +#define LL_USART_IRDA_POWER_NORMAL 0x00000000U /*!< IrDA normal power mode */ +#define LL_USART_IRDA_POWER_LOW USART_CR3_IRLP /*!< IrDA low power mode */ +/** + * @} + */ + +/** @defgroup USART_LL_EC_LINBREAK_DETECT LIN Break Detection Length + * @{ + */ +#define LL_USART_LINBREAK_DETECT_10B 0x00000000U /*!< 10-bit break detection method selected */ +#define LL_USART_LINBREAK_DETECT_11B USART_CR2_LBDL /*!< 11-bit break detection method selected */ +/** + * @} + */ + +/** + * @} + */ + +/* Exported macro ------------------------------------------------------------*/ +/** @defgroup USART_LL_Exported_Macros USART Exported Macros + * @{ + */ + +/** @defgroup USART_LL_EM_WRITE_READ Common Write and read registers Macros + * @{ + */ + +/** + * @brief Write a value in USART register + * @param __INSTANCE__ USART Instance + * @param __REG__ Register to be written + * @param __VALUE__ Value to be written in the register + * @retval None + */ +#define LL_USART_WriteReg(__INSTANCE__, __REG__, __VALUE__) WRITE_REG(__INSTANCE__->__REG__, (__VALUE__)) + +/** + * @brief Read a value in USART register + * @param __INSTANCE__ USART Instance + * @param __REG__ Register to be read + * @retval Register value + */ +#define LL_USART_ReadReg(__INSTANCE__, __REG__) READ_REG(__INSTANCE__->__REG__) +/** + * @} + */ + +/** @defgroup USART_LL_EM_Exported_Macros_Helper Exported_Macros_Helper + * @{ + */ + +/** + * @brief Compute USARTDIV value according to Peripheral Clock and + * expected Baud Rate in 8 bits sampling mode (32 bits value of USARTDIV is returned) + * @param __PERIPHCLK__ Peripheral Clock frequency used for USART instance + * @param __BAUDRATE__ Baud rate value to achieve + * @retval USARTDIV value to be used for BRR register filling in OverSampling_8 case + */ +#define __LL_USART_DIV_SAMPLING8_100(__PERIPHCLK__, __BAUDRATE__) ((uint32_t)((((uint64_t)(__PERIPHCLK__))*25)/(2*((uint64_t)(__BAUDRATE__))))) +#define __LL_USART_DIVMANT_SAMPLING8(__PERIPHCLK__, __BAUDRATE__) (__LL_USART_DIV_SAMPLING8_100((__PERIPHCLK__), (__BAUDRATE__))/100) +#define __LL_USART_DIVFRAQ_SAMPLING8(__PERIPHCLK__, __BAUDRATE__) ((((__LL_USART_DIV_SAMPLING8_100((__PERIPHCLK__), (__BAUDRATE__)) - (__LL_USART_DIVMANT_SAMPLING8((__PERIPHCLK__), (__BAUDRATE__)) * 100)) * 8)\ + + 50) / 100) +/* UART BRR = mantissa + overflow + fraction + = (UART DIVMANT << 4) + ((UART DIVFRAQ & 0xF8) << 1) + (UART DIVFRAQ & 0x07) */ +#define __LL_USART_DIV_SAMPLING8(__PERIPHCLK__, __BAUDRATE__) (((__LL_USART_DIVMANT_SAMPLING8((__PERIPHCLK__), (__BAUDRATE__)) << 4) + \ + ((__LL_USART_DIVFRAQ_SAMPLING8((__PERIPHCLK__), (__BAUDRATE__)) & 0xF8) << 1)) + \ + (__LL_USART_DIVFRAQ_SAMPLING8((__PERIPHCLK__), (__BAUDRATE__)) & 0x07)) + +/** + * @brief Compute USARTDIV value according to Peripheral Clock and + * expected Baud Rate in 16 bits sampling mode (32 bits value of USARTDIV is returned) + * @param __PERIPHCLK__ Peripheral Clock frequency used for USART instance + * @param __BAUDRATE__ Baud rate value to achieve + * @retval USARTDIV value to be used for BRR register filling in OverSampling_16 case + */ +#define __LL_USART_DIV_SAMPLING16_100(__PERIPHCLK__, __BAUDRATE__) ((uint32_t)((((uint64_t)(__PERIPHCLK__))*25)/(4*((uint64_t)(__BAUDRATE__))))) +#define __LL_USART_DIVMANT_SAMPLING16(__PERIPHCLK__, __BAUDRATE__) (__LL_USART_DIV_SAMPLING16_100((__PERIPHCLK__), (__BAUDRATE__))/100) +#define __LL_USART_DIVFRAQ_SAMPLING16(__PERIPHCLK__, __BAUDRATE__) ((((__LL_USART_DIV_SAMPLING16_100((__PERIPHCLK__), (__BAUDRATE__)) - (__LL_USART_DIVMANT_SAMPLING16((__PERIPHCLK__), (__BAUDRATE__)) * 100)) * 16)\ + + 50) / 100) +/* USART BRR = mantissa + overflow + fraction + = (USART DIVMANT << 4) + (USART DIVFRAQ & 0xF0) + (USART DIVFRAQ & 0x0F) */ +#define __LL_USART_DIV_SAMPLING16(__PERIPHCLK__, __BAUDRATE__) (((__LL_USART_DIVMANT_SAMPLING16((__PERIPHCLK__), (__BAUDRATE__)) << 4) + \ + (__LL_USART_DIVFRAQ_SAMPLING16((__PERIPHCLK__), (__BAUDRATE__)) & 0xF0)) + \ + (__LL_USART_DIVFRAQ_SAMPLING16((__PERIPHCLK__), (__BAUDRATE__)) & 0x0F)) + +/** + * @} + */ + +/** + * @} + */ + +/* Exported functions --------------------------------------------------------*/ + +/** @defgroup USART_LL_Exported_Functions USART Exported Functions + * @{ + */ + +/** @defgroup USART_LL_EF_Configuration Configuration functions + * @{ + */ + +/** + * @brief USART Enable + * @rmtoll CR1 UE LL_USART_Enable + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_Enable(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR1, USART_CR1_UE); +} + +/** + * @brief USART Disable (all USART prescalers and outputs are disabled) + * @note When USART is disabled, USART prescalers and outputs are stopped immediately, + * and current operations are discarded. The configuration of the USART is kept, but all the status + * flags, in the USARTx_SR are set to their default values. + * @rmtoll CR1 UE LL_USART_Disable + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_Disable(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR1, USART_CR1_UE); +} + +/** + * @brief Indicate if USART is enabled + * @rmtoll CR1 UE LL_USART_IsEnabled + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabled(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR1, USART_CR1_UE) == (USART_CR1_UE)); +} + +/** + * @brief Receiver Enable (Receiver is enabled and begins searching for a start bit) + * @rmtoll CR1 RE LL_USART_EnableDirectionRx + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableDirectionRx(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_RE); +} + +/** + * @brief Receiver Disable + * @rmtoll CR1 RE LL_USART_DisableDirectionRx + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableDirectionRx(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_RE); +} + +/** + * @brief Transmitter Enable + * @rmtoll CR1 TE LL_USART_EnableDirectionTx + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableDirectionTx(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_TE); +} + +/** + * @brief Transmitter Disable + * @rmtoll CR1 TE LL_USART_DisableDirectionTx + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableDirectionTx(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_TE); +} + +/** + * @brief Configure simultaneously enabled/disabled states + * of Transmitter and Receiver + * @rmtoll CR1 RE LL_USART_SetTransferDirection\n + * CR1 TE LL_USART_SetTransferDirection + * @param USARTx USART Instance + * @param TransferDirection This parameter can be one of the following values: + * @arg @ref LL_USART_DIRECTION_NONE + * @arg @ref LL_USART_DIRECTION_RX + * @arg @ref LL_USART_DIRECTION_TX + * @arg @ref LL_USART_DIRECTION_TX_RX + * @retval None + */ +__STATIC_INLINE void LL_USART_SetTransferDirection(USART_TypeDef *USARTx, uint32_t TransferDirection) +{ + ATOMIC_MODIFY_REG(USARTx->CR1, USART_CR1_RE | USART_CR1_TE, TransferDirection); +} + +/** + * @brief Return enabled/disabled states of Transmitter and Receiver + * @rmtoll CR1 RE LL_USART_GetTransferDirection\n + * CR1 TE LL_USART_GetTransferDirection + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_DIRECTION_NONE + * @arg @ref LL_USART_DIRECTION_RX + * @arg @ref LL_USART_DIRECTION_TX + * @arg @ref LL_USART_DIRECTION_TX_RX + */ +__STATIC_INLINE uint32_t LL_USART_GetTransferDirection(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR1, USART_CR1_RE | USART_CR1_TE)); +} + +/** + * @brief Configure Parity (enabled/disabled and parity mode if enabled). + * @note This function selects if hardware parity control (generation and detection) is enabled or disabled. + * When the parity control is enabled (Odd or Even), computed parity bit is inserted at the MSB position + * (9th or 8th bit depending on data width) and parity is checked on the received data. + * @rmtoll CR1 PS LL_USART_SetParity\n + * CR1 PCE LL_USART_SetParity + * @param USARTx USART Instance + * @param Parity This parameter can be one of the following values: + * @arg @ref LL_USART_PARITY_NONE + * @arg @ref LL_USART_PARITY_EVEN + * @arg @ref LL_USART_PARITY_ODD + * @retval None + */ +__STATIC_INLINE void LL_USART_SetParity(USART_TypeDef *USARTx, uint32_t Parity) +{ + MODIFY_REG(USARTx->CR1, USART_CR1_PS | USART_CR1_PCE, Parity); +} + +/** + * @brief Return Parity configuration (enabled/disabled and parity mode if enabled) + * @rmtoll CR1 PS LL_USART_GetParity\n + * CR1 PCE LL_USART_GetParity + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_PARITY_NONE + * @arg @ref LL_USART_PARITY_EVEN + * @arg @ref LL_USART_PARITY_ODD + */ +__STATIC_INLINE uint32_t LL_USART_GetParity(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR1, USART_CR1_PS | USART_CR1_PCE)); +} + +/** + * @brief Set Receiver Wake Up method from Mute mode. + * @rmtoll CR1 WAKE LL_USART_SetWakeUpMethod + * @param USARTx USART Instance + * @param Method This parameter can be one of the following values: + * @arg @ref LL_USART_WAKEUP_IDLELINE + * @arg @ref LL_USART_WAKEUP_ADDRESSMARK + * @retval None + */ +__STATIC_INLINE void LL_USART_SetWakeUpMethod(USART_TypeDef *USARTx, uint32_t Method) +{ + MODIFY_REG(USARTx->CR1, USART_CR1_WAKE, Method); +} + +/** + * @brief Return Receiver Wake Up method from Mute mode + * @rmtoll CR1 WAKE LL_USART_GetWakeUpMethod + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_WAKEUP_IDLELINE + * @arg @ref LL_USART_WAKEUP_ADDRESSMARK + */ +__STATIC_INLINE uint32_t LL_USART_GetWakeUpMethod(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR1, USART_CR1_WAKE)); +} + +/** + * @brief Set Word length (i.e. nb of data bits, excluding start and stop bits) + * @rmtoll CR1 M LL_USART_SetDataWidth + * @param USARTx USART Instance + * @param DataWidth This parameter can be one of the following values: + * @arg @ref LL_USART_DATAWIDTH_8B + * @arg @ref LL_USART_DATAWIDTH_9B + * @retval None + */ +__STATIC_INLINE void LL_USART_SetDataWidth(USART_TypeDef *USARTx, uint32_t DataWidth) +{ + MODIFY_REG(USARTx->CR1, USART_CR1_M, DataWidth); +} + +/** + * @brief Return Word length (i.e. nb of data bits, excluding start and stop bits) + * @rmtoll CR1 M LL_USART_GetDataWidth + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_DATAWIDTH_8B + * @arg @ref LL_USART_DATAWIDTH_9B + */ +__STATIC_INLINE uint32_t LL_USART_GetDataWidth(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR1, USART_CR1_M)); +} + +/** + * @brief Set Oversampling to 8-bit or 16-bit mode + * @rmtoll CR1 OVER8 LL_USART_SetOverSampling + * @param USARTx USART Instance + * @param OverSampling This parameter can be one of the following values: + * @arg @ref LL_USART_OVERSAMPLING_16 + * @arg @ref LL_USART_OVERSAMPLING_8 + * @retval None + */ +__STATIC_INLINE void LL_USART_SetOverSampling(USART_TypeDef *USARTx, uint32_t OverSampling) +{ + MODIFY_REG(USARTx->CR1, USART_CR1_OVER8, OverSampling); +} + +/** + * @brief Return Oversampling mode + * @rmtoll CR1 OVER8 LL_USART_GetOverSampling + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_OVERSAMPLING_16 + * @arg @ref LL_USART_OVERSAMPLING_8 + */ +__STATIC_INLINE uint32_t LL_USART_GetOverSampling(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR1, USART_CR1_OVER8)); +} + +/** + * @brief Configure if Clock pulse of the last data bit is output to the SCLK pin or not + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 LBCL LL_USART_SetLastClkPulseOutput + * @param USARTx USART Instance + * @param LastBitClockPulse This parameter can be one of the following values: + * @arg @ref LL_USART_LASTCLKPULSE_NO_OUTPUT + * @arg @ref LL_USART_LASTCLKPULSE_OUTPUT + * @retval None + */ +__STATIC_INLINE void LL_USART_SetLastClkPulseOutput(USART_TypeDef *USARTx, uint32_t LastBitClockPulse) +{ + MODIFY_REG(USARTx->CR2, USART_CR2_LBCL, LastBitClockPulse); +} + +/** + * @brief Retrieve Clock pulse of the last data bit output configuration + * (Last bit Clock pulse output to the SCLK pin or not) + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 LBCL LL_USART_GetLastClkPulseOutput + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_LASTCLKPULSE_NO_OUTPUT + * @arg @ref LL_USART_LASTCLKPULSE_OUTPUT + */ +__STATIC_INLINE uint32_t LL_USART_GetLastClkPulseOutput(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR2, USART_CR2_LBCL)); +} + +/** + * @brief Select the phase of the clock output on the SCLK pin in synchronous mode + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 CPHA LL_USART_SetClockPhase + * @param USARTx USART Instance + * @param ClockPhase This parameter can be one of the following values: + * @arg @ref LL_USART_PHASE_1EDGE + * @arg @ref LL_USART_PHASE_2EDGE + * @retval None + */ +__STATIC_INLINE void LL_USART_SetClockPhase(USART_TypeDef *USARTx, uint32_t ClockPhase) +{ + MODIFY_REG(USARTx->CR2, USART_CR2_CPHA, ClockPhase); +} + +/** + * @brief Return phase of the clock output on the SCLK pin in synchronous mode + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 CPHA LL_USART_GetClockPhase + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_PHASE_1EDGE + * @arg @ref LL_USART_PHASE_2EDGE + */ +__STATIC_INLINE uint32_t LL_USART_GetClockPhase(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR2, USART_CR2_CPHA)); +} + +/** + * @brief Select the polarity of the clock output on the SCLK pin in synchronous mode + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 CPOL LL_USART_SetClockPolarity + * @param USARTx USART Instance + * @param ClockPolarity This parameter can be one of the following values: + * @arg @ref LL_USART_POLARITY_LOW + * @arg @ref LL_USART_POLARITY_HIGH + * @retval None + */ +__STATIC_INLINE void LL_USART_SetClockPolarity(USART_TypeDef *USARTx, uint32_t ClockPolarity) +{ + MODIFY_REG(USARTx->CR2, USART_CR2_CPOL, ClockPolarity); +} + +/** + * @brief Return polarity of the clock output on the SCLK pin in synchronous mode + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 CPOL LL_USART_GetClockPolarity + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_POLARITY_LOW + * @arg @ref LL_USART_POLARITY_HIGH + */ +__STATIC_INLINE uint32_t LL_USART_GetClockPolarity(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR2, USART_CR2_CPOL)); +} + +/** + * @brief Configure Clock signal format (Phase Polarity and choice about output of last bit clock pulse) + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @note Call of this function is equivalent to following function call sequence : + * - Clock Phase configuration using @ref LL_USART_SetClockPhase() function + * - Clock Polarity configuration using @ref LL_USART_SetClockPolarity() function + * - Output of Last bit Clock pulse configuration using @ref LL_USART_SetLastClkPulseOutput() function + * @rmtoll CR2 CPHA LL_USART_ConfigClock\n + * CR2 CPOL LL_USART_ConfigClock\n + * CR2 LBCL LL_USART_ConfigClock + * @param USARTx USART Instance + * @param Phase This parameter can be one of the following values: + * @arg @ref LL_USART_PHASE_1EDGE + * @arg @ref LL_USART_PHASE_2EDGE + * @param Polarity This parameter can be one of the following values: + * @arg @ref LL_USART_POLARITY_LOW + * @arg @ref LL_USART_POLARITY_HIGH + * @param LBCPOutput This parameter can be one of the following values: + * @arg @ref LL_USART_LASTCLKPULSE_NO_OUTPUT + * @arg @ref LL_USART_LASTCLKPULSE_OUTPUT + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigClock(USART_TypeDef *USARTx, uint32_t Phase, uint32_t Polarity, uint32_t LBCPOutput) +{ + MODIFY_REG(USARTx->CR2, USART_CR2_CPHA | USART_CR2_CPOL | USART_CR2_LBCL, Phase | Polarity | LBCPOutput); +} + +/** + * @brief Enable Clock output on SCLK pin + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 CLKEN LL_USART_EnableSCLKOutput + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableSCLKOutput(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR2, USART_CR2_CLKEN); +} + +/** + * @brief Disable Clock output on SCLK pin + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 CLKEN LL_USART_DisableSCLKOutput + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableSCLKOutput(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR2, USART_CR2_CLKEN); +} + +/** + * @brief Indicate if Clock output on SCLK pin is enabled + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @rmtoll CR2 CLKEN LL_USART_IsEnabledSCLKOutput + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledSCLKOutput(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR2, USART_CR2_CLKEN) == (USART_CR2_CLKEN)); +} + +/** + * @brief Set the length of the stop bits + * @rmtoll CR2 STOP LL_USART_SetStopBitsLength + * @param USARTx USART Instance + * @param StopBits This parameter can be one of the following values: + * @arg @ref LL_USART_STOPBITS_0_5 + * @arg @ref LL_USART_STOPBITS_1 + * @arg @ref LL_USART_STOPBITS_1_5 + * @arg @ref LL_USART_STOPBITS_2 + * @retval None + */ +__STATIC_INLINE void LL_USART_SetStopBitsLength(USART_TypeDef *USARTx, uint32_t StopBits) +{ + MODIFY_REG(USARTx->CR2, USART_CR2_STOP, StopBits); +} + +/** + * @brief Retrieve the length of the stop bits + * @rmtoll CR2 STOP LL_USART_GetStopBitsLength + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_STOPBITS_0_5 + * @arg @ref LL_USART_STOPBITS_1 + * @arg @ref LL_USART_STOPBITS_1_5 + * @arg @ref LL_USART_STOPBITS_2 + */ +__STATIC_INLINE uint32_t LL_USART_GetStopBitsLength(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR2, USART_CR2_STOP)); +} + +/** + * @brief Configure Character frame format (Datawidth, Parity control, Stop Bits) + * @note Call of this function is equivalent to following function call sequence : + * - Data Width configuration using @ref LL_USART_SetDataWidth() function + * - Parity Control and mode configuration using @ref LL_USART_SetParity() function + * - Stop bits configuration using @ref LL_USART_SetStopBitsLength() function + * @rmtoll CR1 PS LL_USART_ConfigCharacter\n + * CR1 PCE LL_USART_ConfigCharacter\n + * CR1 M LL_USART_ConfigCharacter\n + * CR2 STOP LL_USART_ConfigCharacter + * @param USARTx USART Instance + * @param DataWidth This parameter can be one of the following values: + * @arg @ref LL_USART_DATAWIDTH_8B + * @arg @ref LL_USART_DATAWIDTH_9B + * @param Parity This parameter can be one of the following values: + * @arg @ref LL_USART_PARITY_NONE + * @arg @ref LL_USART_PARITY_EVEN + * @arg @ref LL_USART_PARITY_ODD + * @param StopBits This parameter can be one of the following values: + * @arg @ref LL_USART_STOPBITS_0_5 + * @arg @ref LL_USART_STOPBITS_1 + * @arg @ref LL_USART_STOPBITS_1_5 + * @arg @ref LL_USART_STOPBITS_2 + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigCharacter(USART_TypeDef *USARTx, uint32_t DataWidth, uint32_t Parity, + uint32_t StopBits) +{ + MODIFY_REG(USARTx->CR1, USART_CR1_PS | USART_CR1_PCE | USART_CR1_M, Parity | DataWidth); + MODIFY_REG(USARTx->CR2, USART_CR2_STOP, StopBits); +} + +/** + * @brief Set Address of the USART node. + * @note This is used in multiprocessor communication during Mute mode or Stop mode, + * for wake up with address mark detection. + * @rmtoll CR2 ADD LL_USART_SetNodeAddress + * @param USARTx USART Instance + * @param NodeAddress 4 bit Address of the USART node. + * @retval None + */ +__STATIC_INLINE void LL_USART_SetNodeAddress(USART_TypeDef *USARTx, uint32_t NodeAddress) +{ + MODIFY_REG(USARTx->CR2, USART_CR2_ADD, (NodeAddress & USART_CR2_ADD)); +} + +/** + * @brief Return 4 bit Address of the USART node as set in ADD field of CR2. + * @note only 4bits (b3-b0) of returned value are relevant (b31-b4 are not relevant) + * @rmtoll CR2 ADD LL_USART_GetNodeAddress + * @param USARTx USART Instance + * @retval Address of the USART node (Value between Min_Data=0 and Max_Data=255) + */ +__STATIC_INLINE uint32_t LL_USART_GetNodeAddress(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR2, USART_CR2_ADD)); +} + +/** + * @brief Enable RTS HW Flow Control + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 RTSE LL_USART_EnableRTSHWFlowCtrl + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableRTSHWFlowCtrl(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR3, USART_CR3_RTSE); +} + +/** + * @brief Disable RTS HW Flow Control + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 RTSE LL_USART_DisableRTSHWFlowCtrl + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableRTSHWFlowCtrl(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR3, USART_CR3_RTSE); +} + +/** + * @brief Enable CTS HW Flow Control + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 CTSE LL_USART_EnableCTSHWFlowCtrl + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableCTSHWFlowCtrl(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR3, USART_CR3_CTSE); +} + +/** + * @brief Disable CTS HW Flow Control + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 CTSE LL_USART_DisableCTSHWFlowCtrl + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableCTSHWFlowCtrl(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR3, USART_CR3_CTSE); +} + +/** + * @brief Configure HW Flow Control mode (both CTS and RTS) + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 RTSE LL_USART_SetHWFlowCtrl\n + * CR3 CTSE LL_USART_SetHWFlowCtrl + * @param USARTx USART Instance + * @param HardwareFlowControl This parameter can be one of the following values: + * @arg @ref LL_USART_HWCONTROL_NONE + * @arg @ref LL_USART_HWCONTROL_RTS + * @arg @ref LL_USART_HWCONTROL_CTS + * @arg @ref LL_USART_HWCONTROL_RTS_CTS + * @retval None + */ +__STATIC_INLINE void LL_USART_SetHWFlowCtrl(USART_TypeDef *USARTx, uint32_t HardwareFlowControl) +{ + MODIFY_REG(USARTx->CR3, USART_CR3_RTSE | USART_CR3_CTSE, HardwareFlowControl); +} + +/** + * @brief Return HW Flow Control configuration (both CTS and RTS) + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 RTSE LL_USART_GetHWFlowCtrl\n + * CR3 CTSE LL_USART_GetHWFlowCtrl + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_HWCONTROL_NONE + * @arg @ref LL_USART_HWCONTROL_RTS + * @arg @ref LL_USART_HWCONTROL_CTS + * @arg @ref LL_USART_HWCONTROL_RTS_CTS + */ +__STATIC_INLINE uint32_t LL_USART_GetHWFlowCtrl(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR3, USART_CR3_RTSE | USART_CR3_CTSE)); +} + +/** + * @brief Enable One bit sampling method + * @rmtoll CR3 ONEBIT LL_USART_EnableOneBitSamp + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableOneBitSamp(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR3, USART_CR3_ONEBIT); +} + +/** + * @brief Disable One bit sampling method + * @rmtoll CR3 ONEBIT LL_USART_DisableOneBitSamp + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableOneBitSamp(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR3, USART_CR3_ONEBIT); +} + +/** + * @brief Indicate if One bit sampling method is enabled + * @rmtoll CR3 ONEBIT LL_USART_IsEnabledOneBitSamp + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledOneBitSamp(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_ONEBIT) == (USART_CR3_ONEBIT)); +} + +/** + * @brief Configure USART BRR register for achieving expected Baud Rate value. + * @note Compute and set USARTDIV value in BRR Register (full BRR content) + * according to used Peripheral Clock, Oversampling mode, and expected Baud Rate values + * @note Peripheral clock and Baud rate values provided as function parameters should be valid + * (Baud rate value != 0) + * @rmtoll BRR BRR LL_USART_SetBaudRate + * @param USARTx USART Instance + * @param PeriphClk Peripheral Clock + * @param OverSampling This parameter can be one of the following values: + * @arg @ref LL_USART_OVERSAMPLING_16 + * @arg @ref LL_USART_OVERSAMPLING_8 + * @param BaudRate Baud Rate + * @retval None + */ +__STATIC_INLINE void LL_USART_SetBaudRate(USART_TypeDef *USARTx, uint32_t PeriphClk, uint32_t OverSampling, + uint32_t BaudRate) +{ + if (OverSampling == LL_USART_OVERSAMPLING_8) + { + USARTx->BRR = (uint16_t)(__LL_USART_DIV_SAMPLING8(PeriphClk, BaudRate)); + } + else + { + USARTx->BRR = (uint16_t)(__LL_USART_DIV_SAMPLING16(PeriphClk, BaudRate)); + } +} + +/** + * @brief Return current Baud Rate value, according to USARTDIV present in BRR register + * (full BRR content), and to used Peripheral Clock and Oversampling mode values + * @note In case of non-initialized or invalid value stored in BRR register, value 0 will be returned. + * @rmtoll BRR BRR LL_USART_GetBaudRate + * @param USARTx USART Instance + * @param PeriphClk Peripheral Clock + * @param OverSampling This parameter can be one of the following values: + * @arg @ref LL_USART_OVERSAMPLING_16 + * @arg @ref LL_USART_OVERSAMPLING_8 + * @retval Baud Rate + */ +__STATIC_INLINE uint32_t LL_USART_GetBaudRate(USART_TypeDef *USARTx, uint32_t PeriphClk, uint32_t OverSampling) +{ + uint32_t usartdiv = 0x0U; + uint32_t brrresult = 0x0U; + + usartdiv = USARTx->BRR; + + if (OverSampling == LL_USART_OVERSAMPLING_8) + { + if ((usartdiv & 0xFFF7U) != 0U) + { + usartdiv = (uint16_t)((usartdiv & 0xFFF0U) | ((usartdiv & 0x0007U) << 1U)) ; + brrresult = (PeriphClk * 2U) / usartdiv; + } + } + else + { + if ((usartdiv & 0xFFFFU) != 0U) + { + brrresult = PeriphClk / usartdiv; + } + } + return (brrresult); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_Configuration_IRDA Configuration functions related to Irda feature + * @{ + */ + +/** + * @brief Enable IrDA mode + * @note Macro @ref IS_IRDA_INSTANCE(USARTx) can be used to check whether or not + * IrDA feature is supported by the USARTx instance. + * @rmtoll CR3 IREN LL_USART_EnableIrda + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIrda(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR3, USART_CR3_IREN); +} + +/** + * @brief Disable IrDA mode + * @note Macro @ref IS_IRDA_INSTANCE(USARTx) can be used to check whether or not + * IrDA feature is supported by the USARTx instance. + * @rmtoll CR3 IREN LL_USART_DisableIrda + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIrda(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR3, USART_CR3_IREN); +} + +/** + * @brief Indicate if IrDA mode is enabled + * @note Macro @ref IS_IRDA_INSTANCE(USARTx) can be used to check whether or not + * IrDA feature is supported by the USARTx instance. + * @rmtoll CR3 IREN LL_USART_IsEnabledIrda + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIrda(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_IREN) == (USART_CR3_IREN)); +} + +/** + * @brief Configure IrDA Power Mode (Normal or Low Power) + * @note Macro @ref IS_IRDA_INSTANCE(USARTx) can be used to check whether or not + * IrDA feature is supported by the USARTx instance. + * @rmtoll CR3 IRLP LL_USART_SetIrdaPowerMode + * @param USARTx USART Instance + * @param PowerMode This parameter can be one of the following values: + * @arg @ref LL_USART_IRDA_POWER_NORMAL + * @arg @ref LL_USART_IRDA_POWER_LOW + * @retval None + */ +__STATIC_INLINE void LL_USART_SetIrdaPowerMode(USART_TypeDef *USARTx, uint32_t PowerMode) +{ + MODIFY_REG(USARTx->CR3, USART_CR3_IRLP, PowerMode); +} + +/** + * @brief Retrieve IrDA Power Mode configuration (Normal or Low Power) + * @note Macro @ref IS_IRDA_INSTANCE(USARTx) can be used to check whether or not + * IrDA feature is supported by the USARTx instance. + * @rmtoll CR3 IRLP LL_USART_GetIrdaPowerMode + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_IRDA_POWER_NORMAL + * @arg @ref LL_USART_PHASE_2EDGE + */ +__STATIC_INLINE uint32_t LL_USART_GetIrdaPowerMode(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR3, USART_CR3_IRLP)); +} + +/** + * @brief Set Irda prescaler value, used for dividing the USART clock source + * to achieve the Irda Low Power frequency (8 bits value) + * @note Macro @ref IS_IRDA_INSTANCE(USARTx) can be used to check whether or not + * IrDA feature is supported by the USARTx instance. + * @rmtoll GTPR PSC LL_USART_SetIrdaPrescaler + * @param USARTx USART Instance + * @param PrescalerValue Value between Min_Data=0x00 and Max_Data=0xFF + * @retval None + */ +__STATIC_INLINE void LL_USART_SetIrdaPrescaler(USART_TypeDef *USARTx, uint32_t PrescalerValue) +{ + MODIFY_REG(USARTx->GTPR, USART_GTPR_PSC, PrescalerValue); +} + +/** + * @brief Return Irda prescaler value, used for dividing the USART clock source + * to achieve the Irda Low Power frequency (8 bits value) + * @note Macro @ref IS_IRDA_INSTANCE(USARTx) can be used to check whether or not + * IrDA feature is supported by the USARTx instance. + * @rmtoll GTPR PSC LL_USART_GetIrdaPrescaler + * @param USARTx USART Instance + * @retval Irda prescaler value (Value between Min_Data=0x00 and Max_Data=0xFF) + */ +__STATIC_INLINE uint32_t LL_USART_GetIrdaPrescaler(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->GTPR, USART_GTPR_PSC)); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_Configuration_Smartcard Configuration functions related to Smartcard feature + * @{ + */ + +/** + * @brief Enable Smartcard NACK transmission + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll CR3 NACK LL_USART_EnableSmartcardNACK + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableSmartcardNACK(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR3, USART_CR3_NACK); +} + +/** + * @brief Disable Smartcard NACK transmission + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll CR3 NACK LL_USART_DisableSmartcardNACK + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableSmartcardNACK(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR3, USART_CR3_NACK); +} + +/** + * @brief Indicate if Smartcard NACK transmission is enabled + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll CR3 NACK LL_USART_IsEnabledSmartcardNACK + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledSmartcardNACK(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_NACK) == (USART_CR3_NACK)); +} + +/** + * @brief Enable Smartcard mode + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll CR3 SCEN LL_USART_EnableSmartcard + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableSmartcard(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR3, USART_CR3_SCEN); +} + +/** + * @brief Disable Smartcard mode + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll CR3 SCEN LL_USART_DisableSmartcard + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableSmartcard(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR3, USART_CR3_SCEN); +} + +/** + * @brief Indicate if Smartcard mode is enabled + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll CR3 SCEN LL_USART_IsEnabledSmartcard + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledSmartcard(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_SCEN) == (USART_CR3_SCEN)); +} + +/** + * @brief Set Smartcard prescaler value, used for dividing the USART clock + * source to provide the SMARTCARD Clock (5 bits value) + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll GTPR PSC LL_USART_SetSmartcardPrescaler + * @param USARTx USART Instance + * @param PrescalerValue Value between Min_Data=0 and Max_Data=31 + * @retval None + */ +__STATIC_INLINE void LL_USART_SetSmartcardPrescaler(USART_TypeDef *USARTx, uint32_t PrescalerValue) +{ + MODIFY_REG(USARTx->GTPR, USART_GTPR_PSC, PrescalerValue); +} + +/** + * @brief Return Smartcard prescaler value, used for dividing the USART clock + * source to provide the SMARTCARD Clock (5 bits value) + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll GTPR PSC LL_USART_GetSmartcardPrescaler + * @param USARTx USART Instance + * @retval Smartcard prescaler value (Value between Min_Data=0 and Max_Data=31) + */ +__STATIC_INLINE uint32_t LL_USART_GetSmartcardPrescaler(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->GTPR, USART_GTPR_PSC)); +} + +/** + * @brief Set Smartcard Guard time value, expressed in nb of baud clocks periods + * (GT[7:0] bits : Guard time value) + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll GTPR GT LL_USART_SetSmartcardGuardTime + * @param USARTx USART Instance + * @param GuardTime Value between Min_Data=0x00 and Max_Data=0xFF + * @retval None + */ +__STATIC_INLINE void LL_USART_SetSmartcardGuardTime(USART_TypeDef *USARTx, uint32_t GuardTime) +{ + MODIFY_REG(USARTx->GTPR, USART_GTPR_GT, GuardTime << USART_POSITION_GTPR_GT); +} + +/** + * @brief Return Smartcard Guard time value, expressed in nb of baud clocks periods + * (GT[7:0] bits : Guard time value) + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @rmtoll GTPR GT LL_USART_GetSmartcardGuardTime + * @param USARTx USART Instance + * @retval Smartcard Guard time value (Value between Min_Data=0x00 and Max_Data=0xFF) + */ +__STATIC_INLINE uint32_t LL_USART_GetSmartcardGuardTime(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->GTPR, USART_GTPR_GT) >> USART_POSITION_GTPR_GT); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_Configuration_HalfDuplex Configuration functions related to Half Duplex feature + * @{ + */ + +/** + * @brief Enable Single Wire Half-Duplex mode + * @note Macro @ref IS_UART_HALFDUPLEX_INSTANCE(USARTx) can be used to check whether or not + * Half-Duplex mode is supported by the USARTx instance. + * @rmtoll CR3 HDSEL LL_USART_EnableHalfDuplex + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableHalfDuplex(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR3, USART_CR3_HDSEL); +} + +/** + * @brief Disable Single Wire Half-Duplex mode + * @note Macro @ref IS_UART_HALFDUPLEX_INSTANCE(USARTx) can be used to check whether or not + * Half-Duplex mode is supported by the USARTx instance. + * @rmtoll CR3 HDSEL LL_USART_DisableHalfDuplex + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableHalfDuplex(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR3, USART_CR3_HDSEL); +} + +/** + * @brief Indicate if Single Wire Half-Duplex mode is enabled + * @note Macro @ref IS_UART_HALFDUPLEX_INSTANCE(USARTx) can be used to check whether or not + * Half-Duplex mode is supported by the USARTx instance. + * @rmtoll CR3 HDSEL LL_USART_IsEnabledHalfDuplex + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledHalfDuplex(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_HDSEL) == (USART_CR3_HDSEL)); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_Configuration_LIN Configuration functions related to LIN feature + * @{ + */ + +/** + * @brief Set LIN Break Detection Length + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll CR2 LBDL LL_USART_SetLINBrkDetectionLen + * @param USARTx USART Instance + * @param LINBDLength This parameter can be one of the following values: + * @arg @ref LL_USART_LINBREAK_DETECT_10B + * @arg @ref LL_USART_LINBREAK_DETECT_11B + * @retval None + */ +__STATIC_INLINE void LL_USART_SetLINBrkDetectionLen(USART_TypeDef *USARTx, uint32_t LINBDLength) +{ + MODIFY_REG(USARTx->CR2, USART_CR2_LBDL, LINBDLength); +} + +/** + * @brief Return LIN Break Detection Length + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll CR2 LBDL LL_USART_GetLINBrkDetectionLen + * @param USARTx USART Instance + * @retval Returned value can be one of the following values: + * @arg @ref LL_USART_LINBREAK_DETECT_10B + * @arg @ref LL_USART_LINBREAK_DETECT_11B + */ +__STATIC_INLINE uint32_t LL_USART_GetLINBrkDetectionLen(USART_TypeDef *USARTx) +{ + return (uint32_t)(READ_BIT(USARTx->CR2, USART_CR2_LBDL)); +} + +/** + * @brief Enable LIN mode + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll CR2 LINEN LL_USART_EnableLIN + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableLIN(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR2, USART_CR2_LINEN); +} + +/** + * @brief Disable LIN mode + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll CR2 LINEN LL_USART_DisableLIN + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableLIN(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR2, USART_CR2_LINEN); +} + +/** + * @brief Indicate if LIN mode is enabled + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll CR2 LINEN LL_USART_IsEnabledLIN + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledLIN(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR2, USART_CR2_LINEN) == (USART_CR2_LINEN)); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_AdvancedConfiguration Advanced Configurations services + * @{ + */ + +/** + * @brief Perform basic configuration of USART for enabling use in Asynchronous Mode (UART) + * @note In UART mode, the following bits must be kept cleared: + * - LINEN bit in the USART_CR2 register, + * - CLKEN bit in the USART_CR2 register, + * - SCEN bit in the USART_CR3 register, + * - IREN bit in the USART_CR3 register, + * - HDSEL bit in the USART_CR3 register. + * @note Call of this function is equivalent to following function call sequence : + * - Clear LINEN in CR2 using @ref LL_USART_DisableLIN() function + * - Clear CLKEN in CR2 using @ref LL_USART_DisableSCLKOutput() function + * - Clear SCEN in CR3 using @ref LL_USART_DisableSmartcard() function + * - Clear IREN in CR3 using @ref LL_USART_DisableIrda() function + * - Clear HDSEL in CR3 using @ref LL_USART_DisableHalfDuplex() function + * @note Other remaining configurations items related to Asynchronous Mode + * (as Baud Rate, Word length, Parity, ...) should be set using + * dedicated functions + * @rmtoll CR2 LINEN LL_USART_ConfigAsyncMode\n + * CR2 CLKEN LL_USART_ConfigAsyncMode\n + * CR3 SCEN LL_USART_ConfigAsyncMode\n + * CR3 IREN LL_USART_ConfigAsyncMode\n + * CR3 HDSEL LL_USART_ConfigAsyncMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigAsyncMode(USART_TypeDef *USARTx) +{ + /* In Asynchronous mode, the following bits must be kept cleared: + - LINEN, CLKEN bits in the USART_CR2 register, + - SCEN, IREN and HDSEL bits in the USART_CR3 register.*/ + CLEAR_BIT(USARTx->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(USARTx->CR3, (USART_CR3_SCEN | USART_CR3_IREN | USART_CR3_HDSEL)); +} + +/** + * @brief Perform basic configuration of USART for enabling use in Synchronous Mode + * @note In Synchronous mode, the following bits must be kept cleared: + * - LINEN bit in the USART_CR2 register, + * - SCEN bit in the USART_CR3 register, + * - IREN bit in the USART_CR3 register, + * - HDSEL bit in the USART_CR3 register. + * This function also sets the USART in Synchronous mode. + * @note Macro @ref IS_USART_INSTANCE(USARTx) can be used to check whether or not + * Synchronous mode is supported by the USARTx instance. + * @note Call of this function is equivalent to following function call sequence : + * - Clear LINEN in CR2 using @ref LL_USART_DisableLIN() function + * - Clear IREN in CR3 using @ref LL_USART_DisableIrda() function + * - Clear SCEN in CR3 using @ref LL_USART_DisableSmartcard() function + * - Clear HDSEL in CR3 using @ref LL_USART_DisableHalfDuplex() function + * - Set CLKEN in CR2 using @ref LL_USART_EnableSCLKOutput() function + * @note Other remaining configurations items related to Synchronous Mode + * (as Baud Rate, Word length, Parity, Clock Polarity, ...) should be set using + * dedicated functions + * @rmtoll CR2 LINEN LL_USART_ConfigSyncMode\n + * CR2 CLKEN LL_USART_ConfigSyncMode\n + * CR3 SCEN LL_USART_ConfigSyncMode\n + * CR3 IREN LL_USART_ConfigSyncMode\n + * CR3 HDSEL LL_USART_ConfigSyncMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigSyncMode(USART_TypeDef *USARTx) +{ + /* In Synchronous mode, the following bits must be kept cleared: + - LINEN bit in the USART_CR2 register, + - SCEN, IREN and HDSEL bits in the USART_CR3 register.*/ + CLEAR_BIT(USARTx->CR2, (USART_CR2_LINEN)); + CLEAR_BIT(USARTx->CR3, (USART_CR3_SCEN | USART_CR3_IREN | USART_CR3_HDSEL)); + /* set the UART/USART in Synchronous mode */ + SET_BIT(USARTx->CR2, USART_CR2_CLKEN); +} + +/** + * @brief Perform basic configuration of USART for enabling use in LIN Mode + * @note In LIN mode, the following bits must be kept cleared: + * - STOP and CLKEN bits in the USART_CR2 register, + * - SCEN bit in the USART_CR3 register, + * - IREN bit in the USART_CR3 register, + * - HDSEL bit in the USART_CR3 register. + * This function also set the UART/USART in LIN mode. + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @note Call of this function is equivalent to following function call sequence : + * - Clear CLKEN in CR2 using @ref LL_USART_DisableSCLKOutput() function + * - Clear STOP in CR2 using @ref LL_USART_SetStopBitsLength() function + * - Clear SCEN in CR3 using @ref LL_USART_DisableSmartcard() function + * - Clear IREN in CR3 using @ref LL_USART_DisableIrda() function + * - Clear HDSEL in CR3 using @ref LL_USART_DisableHalfDuplex() function + * - Set LINEN in CR2 using @ref LL_USART_EnableLIN() function + * @note Other remaining configurations items related to LIN Mode + * (as Baud Rate, Word length, LIN Break Detection Length, ...) should be set using + * dedicated functions + * @rmtoll CR2 CLKEN LL_USART_ConfigLINMode\n + * CR2 STOP LL_USART_ConfigLINMode\n + * CR2 LINEN LL_USART_ConfigLINMode\n + * CR3 IREN LL_USART_ConfigLINMode\n + * CR3 SCEN LL_USART_ConfigLINMode\n + * CR3 HDSEL LL_USART_ConfigLINMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigLINMode(USART_TypeDef *USARTx) +{ + /* In LIN mode, the following bits must be kept cleared: + - STOP and CLKEN bits in the USART_CR2 register, + - IREN, SCEN and HDSEL bits in the USART_CR3 register.*/ + CLEAR_BIT(USARTx->CR2, (USART_CR2_CLKEN | USART_CR2_STOP)); + CLEAR_BIT(USARTx->CR3, (USART_CR3_IREN | USART_CR3_SCEN | USART_CR3_HDSEL)); + /* Set the UART/USART in LIN mode */ + SET_BIT(USARTx->CR2, USART_CR2_LINEN); +} + +/** + * @brief Perform basic configuration of USART for enabling use in Half Duplex Mode + * @note In Half Duplex mode, the following bits must be kept cleared: + * - LINEN bit in the USART_CR2 register, + * - CLKEN bit in the USART_CR2 register, + * - SCEN bit in the USART_CR3 register, + * - IREN bit in the USART_CR3 register, + * This function also sets the UART/USART in Half Duplex mode. + * @note Macro @ref IS_UART_HALFDUPLEX_INSTANCE(USARTx) can be used to check whether or not + * Half-Duplex mode is supported by the USARTx instance. + * @note Call of this function is equivalent to following function call sequence : + * - Clear LINEN in CR2 using @ref LL_USART_DisableLIN() function + * - Clear CLKEN in CR2 using @ref LL_USART_DisableSCLKOutput() function + * - Clear SCEN in CR3 using @ref LL_USART_DisableSmartcard() function + * - Clear IREN in CR3 using @ref LL_USART_DisableIrda() function + * - Set HDSEL in CR3 using @ref LL_USART_EnableHalfDuplex() function + * @note Other remaining configurations items related to Half Duplex Mode + * (as Baud Rate, Word length, Parity, ...) should be set using + * dedicated functions + * @rmtoll CR2 LINEN LL_USART_ConfigHalfDuplexMode\n + * CR2 CLKEN LL_USART_ConfigHalfDuplexMode\n + * CR3 HDSEL LL_USART_ConfigHalfDuplexMode\n + * CR3 SCEN LL_USART_ConfigHalfDuplexMode\n + * CR3 IREN LL_USART_ConfigHalfDuplexMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigHalfDuplexMode(USART_TypeDef *USARTx) +{ + /* In Half Duplex mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(USARTx->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(USARTx->CR3, (USART_CR3_SCEN | USART_CR3_IREN)); + /* set the UART/USART in Half Duplex mode */ + SET_BIT(USARTx->CR3, USART_CR3_HDSEL); +} + +/** + * @brief Perform basic configuration of USART for enabling use in Smartcard Mode + * @note In Smartcard mode, the following bits must be kept cleared: + * - LINEN bit in the USART_CR2 register, + * - IREN bit in the USART_CR3 register, + * - HDSEL bit in the USART_CR3 register. + * This function also configures Stop bits to 1.5 bits and + * sets the USART in Smartcard mode (SCEN bit). + * Clock Output is also enabled (CLKEN). + * @note Macro @ref IS_SMARTCARD_INSTANCE(USARTx) can be used to check whether or not + * Smartcard feature is supported by the USARTx instance. + * @note Call of this function is equivalent to following function call sequence : + * - Clear LINEN in CR2 using @ref LL_USART_DisableLIN() function + * - Clear IREN in CR3 using @ref LL_USART_DisableIrda() function + * - Clear HDSEL in CR3 using @ref LL_USART_DisableHalfDuplex() function + * - Configure STOP in CR2 using @ref LL_USART_SetStopBitsLength() function + * - Set CLKEN in CR2 using @ref LL_USART_EnableSCLKOutput() function + * - Set SCEN in CR3 using @ref LL_USART_EnableSmartcard() function + * @note Other remaining configurations items related to Smartcard Mode + * (as Baud Rate, Word length, Parity, ...) should be set using + * dedicated functions + * @rmtoll CR2 LINEN LL_USART_ConfigSmartcardMode\n + * CR2 STOP LL_USART_ConfigSmartcardMode\n + * CR2 CLKEN LL_USART_ConfigSmartcardMode\n + * CR3 HDSEL LL_USART_ConfigSmartcardMode\n + * CR3 SCEN LL_USART_ConfigSmartcardMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigSmartcardMode(USART_TypeDef *USARTx) +{ + /* In Smartcard mode, the following bits must be kept cleared: + - LINEN bit in the USART_CR2 register, + - IREN and HDSEL bits in the USART_CR3 register.*/ + CLEAR_BIT(USARTx->CR2, (USART_CR2_LINEN)); + CLEAR_BIT(USARTx->CR3, (USART_CR3_IREN | USART_CR3_HDSEL)); + /* Configure Stop bits to 1.5 bits */ + /* Synchronous mode is activated by default */ + SET_BIT(USARTx->CR2, (USART_CR2_STOP_0 | USART_CR2_STOP_1 | USART_CR2_CLKEN)); + /* set the UART/USART in Smartcard mode */ + SET_BIT(USARTx->CR3, USART_CR3_SCEN); +} + +/** + * @brief Perform basic configuration of USART for enabling use in Irda Mode + * @note In IRDA mode, the following bits must be kept cleared: + * - LINEN bit in the USART_CR2 register, + * - STOP and CLKEN bits in the USART_CR2 register, + * - SCEN bit in the USART_CR3 register, + * - HDSEL bit in the USART_CR3 register. + * This function also sets the UART/USART in IRDA mode (IREN bit). + * @note Macro @ref IS_IRDA_INSTANCE(USARTx) can be used to check whether or not + * IrDA feature is supported by the USARTx instance. + * @note Call of this function is equivalent to following function call sequence : + * - Clear LINEN in CR2 using @ref LL_USART_DisableLIN() function + * - Clear CLKEN in CR2 using @ref LL_USART_DisableSCLKOutput() function + * - Clear SCEN in CR3 using @ref LL_USART_DisableSmartcard() function + * - Clear HDSEL in CR3 using @ref LL_USART_DisableHalfDuplex() function + * - Configure STOP in CR2 using @ref LL_USART_SetStopBitsLength() function + * - Set IREN in CR3 using @ref LL_USART_EnableIrda() function + * @note Other remaining configurations items related to Irda Mode + * (as Baud Rate, Word length, Power mode, ...) should be set using + * dedicated functions + * @rmtoll CR2 LINEN LL_USART_ConfigIrdaMode\n + * CR2 CLKEN LL_USART_ConfigIrdaMode\n + * CR2 STOP LL_USART_ConfigIrdaMode\n + * CR3 SCEN LL_USART_ConfigIrdaMode\n + * CR3 HDSEL LL_USART_ConfigIrdaMode\n + * CR3 IREN LL_USART_ConfigIrdaMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigIrdaMode(USART_TypeDef *USARTx) +{ + /* In IRDA mode, the following bits must be kept cleared: + - LINEN, STOP and CLKEN bits in the USART_CR2 register, + - SCEN and HDSEL bits in the USART_CR3 register.*/ + CLEAR_BIT(USARTx->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN | USART_CR2_STOP)); + CLEAR_BIT(USARTx->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL)); + /* set the UART/USART in IRDA mode */ + SET_BIT(USARTx->CR3, USART_CR3_IREN); +} + +/** + * @brief Perform basic configuration of USART for enabling use in Multi processor Mode + * (several USARTs connected in a network, one of the USARTs can be the master, + * its TX output connected to the RX inputs of the other slaves USARTs). + * @note In MultiProcessor mode, the following bits must be kept cleared: + * - LINEN bit in the USART_CR2 register, + * - CLKEN bit in the USART_CR2 register, + * - SCEN bit in the USART_CR3 register, + * - IREN bit in the USART_CR3 register, + * - HDSEL bit in the USART_CR3 register. + * @note Call of this function is equivalent to following function call sequence : + * - Clear LINEN in CR2 using @ref LL_USART_DisableLIN() function + * - Clear CLKEN in CR2 using @ref LL_USART_DisableSCLKOutput() function + * - Clear SCEN in CR3 using @ref LL_USART_DisableSmartcard() function + * - Clear IREN in CR3 using @ref LL_USART_DisableIrda() function + * - Clear HDSEL in CR3 using @ref LL_USART_DisableHalfDuplex() function + * @note Other remaining configurations items related to Multi processor Mode + * (as Baud Rate, Wake Up Method, Node address, ...) should be set using + * dedicated functions + * @rmtoll CR2 LINEN LL_USART_ConfigMultiProcessMode\n + * CR2 CLKEN LL_USART_ConfigMultiProcessMode\n + * CR3 SCEN LL_USART_ConfigMultiProcessMode\n + * CR3 HDSEL LL_USART_ConfigMultiProcessMode\n + * CR3 IREN LL_USART_ConfigMultiProcessMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ConfigMultiProcessMode(USART_TypeDef *USARTx) +{ + /* In Multi Processor mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - IREN, SCEN and HDSEL bits in the USART_CR3 register.*/ + CLEAR_BIT(USARTx->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(USARTx->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN)); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_FLAG_Management FLAG_Management + * @{ + */ + +/** + * @brief Check if the USART Parity Error Flag is set or not + * @rmtoll SR PE LL_USART_IsActiveFlag_PE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_PE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_PE) == (USART_SR_PE)); +} + +/** + * @brief Check if the USART Framing Error Flag is set or not + * @rmtoll SR FE LL_USART_IsActiveFlag_FE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_FE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_FE) == (USART_SR_FE)); +} + +/** + * @brief Check if the USART Noise error detected Flag is set or not + * @rmtoll SR NF LL_USART_IsActiveFlag_NE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_NE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_NE) == (USART_SR_NE)); +} + +/** + * @brief Check if the USART OverRun Error Flag is set or not + * @rmtoll SR ORE LL_USART_IsActiveFlag_ORE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_ORE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_ORE) == (USART_SR_ORE)); +} + +/** + * @brief Check if the USART IDLE line detected Flag is set or not + * @rmtoll SR IDLE LL_USART_IsActiveFlag_IDLE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_IDLE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_IDLE) == (USART_SR_IDLE)); +} + +/** + * @brief Check if the USART Read Data Register Not Empty Flag is set or not + * @rmtoll SR RXNE LL_USART_IsActiveFlag_RXNE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_RXNE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_RXNE) == (USART_SR_RXNE)); +} + +/** + * @brief Check if the USART Transmission Complete Flag is set or not + * @rmtoll SR TC LL_USART_IsActiveFlag_TC + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_TC(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_TC) == (USART_SR_TC)); +} + +/** + * @brief Check if the USART Transmit Data Register Empty Flag is set or not + * @rmtoll SR TXE LL_USART_IsActiveFlag_TXE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_TXE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_TXE) == (USART_SR_TXE)); +} + +/** + * @brief Check if the USART LIN Break Detection Flag is set or not + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll SR LBD LL_USART_IsActiveFlag_LBD + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_LBD(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_LBD) == (USART_SR_LBD)); +} + +/** + * @brief Check if the USART CTS Flag is set or not + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll SR CTS LL_USART_IsActiveFlag_nCTS + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_nCTS(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->SR, USART_SR_CTS) == (USART_SR_CTS)); +} + +/** + * @brief Check if the USART Send Break Flag is set or not + * @rmtoll CR1 SBK LL_USART_IsActiveFlag_SBK + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_SBK(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR1, USART_CR1_SBK) == (USART_CR1_SBK)); +} + +/** + * @brief Check if the USART Receive Wake Up from mute mode Flag is set or not + * @rmtoll CR1 RWU LL_USART_IsActiveFlag_RWU + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsActiveFlag_RWU(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR1, USART_CR1_RWU) == (USART_CR1_RWU)); +} + +/** + * @brief Clear Parity Error Flag + * @note Clearing this flag is done by a read access to the USARTx_SR + * register followed by a read access to the USARTx_DR register. + * @note Please also consider that when clearing this flag, other flags as + * NE, FE, ORE, IDLE would also be cleared. + * @rmtoll SR PE LL_USART_ClearFlag_PE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_PE(USART_TypeDef *USARTx) +{ + __IO uint32_t tmpreg; + tmpreg = USARTx->SR; + (void) tmpreg; + tmpreg = USARTx->DR; + (void) tmpreg; +} + +/** + * @brief Clear Framing Error Flag + * @note Clearing this flag is done by a read access to the USARTx_SR + * register followed by a read access to the USARTx_DR register. + * @note Please also consider that when clearing this flag, other flags as + * PE, NE, ORE, IDLE would also be cleared. + * @rmtoll SR FE LL_USART_ClearFlag_FE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_FE(USART_TypeDef *USARTx) +{ + __IO uint32_t tmpreg; + tmpreg = USARTx->SR; + (void) tmpreg; + tmpreg = USARTx->DR; + (void) tmpreg; +} + +/** + * @brief Clear Noise detected Flag + * @note Clearing this flag is done by a read access to the USARTx_SR + * register followed by a read access to the USARTx_DR register. + * @note Please also consider that when clearing this flag, other flags as + * PE, FE, ORE, IDLE would also be cleared. + * @rmtoll SR NF LL_USART_ClearFlag_NE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_NE(USART_TypeDef *USARTx) +{ + __IO uint32_t tmpreg; + tmpreg = USARTx->SR; + (void) tmpreg; + tmpreg = USARTx->DR; + (void) tmpreg; +} + +/** + * @brief Clear OverRun Error Flag + * @note Clearing this flag is done by a read access to the USARTx_SR + * register followed by a read access to the USARTx_DR register. + * @note Please also consider that when clearing this flag, other flags as + * PE, NE, FE, IDLE would also be cleared. + * @rmtoll SR ORE LL_USART_ClearFlag_ORE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_ORE(USART_TypeDef *USARTx) +{ + __IO uint32_t tmpreg; + tmpreg = USARTx->SR; + (void) tmpreg; + tmpreg = USARTx->DR; + (void) tmpreg; +} + +/** + * @brief Clear IDLE line detected Flag + * @note Clearing this flag is done by a read access to the USARTx_SR + * register followed by a read access to the USARTx_DR register. + * @note Please also consider that when clearing this flag, other flags as + * PE, NE, FE, ORE would also be cleared. + * @rmtoll SR IDLE LL_USART_ClearFlag_IDLE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_IDLE(USART_TypeDef *USARTx) +{ + __IO uint32_t tmpreg; + tmpreg = USARTx->SR; + (void) tmpreg; + tmpreg = USARTx->DR; + (void) tmpreg; +} + +/** + * @brief Clear Transmission Complete Flag + * @rmtoll SR TC LL_USART_ClearFlag_TC + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_TC(USART_TypeDef *USARTx) +{ + WRITE_REG(USARTx->SR, ~(USART_SR_TC)); +} + +/** + * @brief Clear RX Not Empty Flag + * @rmtoll SR RXNE LL_USART_ClearFlag_RXNE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_RXNE(USART_TypeDef *USARTx) +{ + WRITE_REG(USARTx->SR, ~(USART_SR_RXNE)); +} + +/** + * @brief Clear LIN Break Detection Flag + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll SR LBD LL_USART_ClearFlag_LBD + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_LBD(USART_TypeDef *USARTx) +{ + WRITE_REG(USARTx->SR, ~(USART_SR_LBD)); +} + +/** + * @brief Clear CTS Interrupt Flag + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll SR CTS LL_USART_ClearFlag_nCTS + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_ClearFlag_nCTS(USART_TypeDef *USARTx) +{ + WRITE_REG(USARTx->SR, ~(USART_SR_CTS)); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_IT_Management IT_Management + * @{ + */ + +/** + * @brief Enable IDLE Interrupt + * @rmtoll CR1 IDLEIE LL_USART_EnableIT_IDLE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIT_IDLE(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_IDLEIE); +} + +/** + * @brief Enable RX Not Empty Interrupt + * @rmtoll CR1 RXNEIE LL_USART_EnableIT_RXNE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIT_RXNE(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_RXNEIE); +} + +/** + * @brief Enable Transmission Complete Interrupt + * @rmtoll CR1 TCIE LL_USART_EnableIT_TC + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIT_TC(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_TCIE); +} + +/** + * @brief Enable TX Empty Interrupt + * @rmtoll CR1 TXEIE LL_USART_EnableIT_TXE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIT_TXE(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_TXEIE); +} + +/** + * @brief Enable Parity Error Interrupt + * @rmtoll CR1 PEIE LL_USART_EnableIT_PE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIT_PE(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR1, USART_CR1_PEIE); +} + +/** + * @brief Enable LIN Break Detection Interrupt + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll CR2 LBDIE LL_USART_EnableIT_LBD + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIT_LBD(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR2, USART_CR2_LBDIE); +} + +/** + * @brief Enable Error Interrupt + * @note When set, Error Interrupt Enable Bit is enabling interrupt generation in case of a framing + * error, overrun error or noise flag (FE=1 or ORE=1 or NF=1 in the USARTx_SR register). + * 0: Interrupt is inhibited + * 1: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the USARTx_SR register. + * @rmtoll CR3 EIE LL_USART_EnableIT_ERROR + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIT_ERROR(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_EIE); +} + +/** + * @brief Enable CTS Interrupt + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 CTSIE LL_USART_EnableIT_CTS + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableIT_CTS(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_CTSIE); +} + +/** + * @brief Disable IDLE Interrupt + * @rmtoll CR1 IDLEIE LL_USART_DisableIT_IDLE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIT_IDLE(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_IDLEIE); +} + +/** + * @brief Disable RX Not Empty Interrupt + * @rmtoll CR1 RXNEIE LL_USART_DisableIT_RXNE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIT_RXNE(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_RXNEIE); +} + +/** + * @brief Disable Transmission Complete Interrupt + * @rmtoll CR1 TCIE LL_USART_DisableIT_TC + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIT_TC(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_TCIE); +} + +/** + * @brief Disable TX Empty Interrupt + * @rmtoll CR1 TXEIE LL_USART_DisableIT_TXE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIT_TXE(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_TXEIE); +} + +/** + * @brief Disable Parity Error Interrupt + * @rmtoll CR1 PEIE LL_USART_DisableIT_PE + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIT_PE(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR1, USART_CR1_PEIE); +} + +/** + * @brief Disable LIN Break Detection Interrupt + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll CR2 LBDIE LL_USART_DisableIT_LBD + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIT_LBD(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR2, USART_CR2_LBDIE); +} + +/** + * @brief Disable Error Interrupt + * @note When set, Error Interrupt Enable Bit is enabling interrupt generation in case of a framing + * error, overrun error or noise flag (FE=1 or ORE=1 or NF=1 in the USARTx_SR register). + * 0: Interrupt is inhibited + * 1: An interrupt is generated when FE=1 or ORE=1 or NF=1 in the USARTx_SR register. + * @rmtoll CR3 EIE LL_USART_DisableIT_ERROR + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIT_ERROR(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_EIE); +} + +/** + * @brief Disable CTS Interrupt + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 CTSIE LL_USART_DisableIT_CTS + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableIT_CTS(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_CTSIE); +} + +/** + * @brief Check if the USART IDLE Interrupt source is enabled or disabled. + * @rmtoll CR1 IDLEIE LL_USART_IsEnabledIT_IDLE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIT_IDLE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR1, USART_CR1_IDLEIE) == (USART_CR1_IDLEIE)); +} + +/** + * @brief Check if the USART RX Not Empty Interrupt is enabled or disabled. + * @rmtoll CR1 RXNEIE LL_USART_IsEnabledIT_RXNE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIT_RXNE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR1, USART_CR1_RXNEIE) == (USART_CR1_RXNEIE)); +} + +/** + * @brief Check if the USART Transmission Complete Interrupt is enabled or disabled. + * @rmtoll CR1 TCIE LL_USART_IsEnabledIT_TC + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIT_TC(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR1, USART_CR1_TCIE) == (USART_CR1_TCIE)); +} + +/** + * @brief Check if the USART TX Empty Interrupt is enabled or disabled. + * @rmtoll CR1 TXEIE LL_USART_IsEnabledIT_TXE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIT_TXE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR1, USART_CR1_TXEIE) == (USART_CR1_TXEIE)); +} + +/** + * @brief Check if the USART Parity Error Interrupt is enabled or disabled. + * @rmtoll CR1 PEIE LL_USART_IsEnabledIT_PE + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIT_PE(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR1, USART_CR1_PEIE) == (USART_CR1_PEIE)); +} + +/** + * @brief Check if the USART LIN Break Detection Interrupt is enabled or disabled. + * @note Macro @ref IS_UART_LIN_INSTANCE(USARTx) can be used to check whether or not + * LIN feature is supported by the USARTx instance. + * @rmtoll CR2 LBDIE LL_USART_IsEnabledIT_LBD + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIT_LBD(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR2, USART_CR2_LBDIE) == (USART_CR2_LBDIE)); +} + +/** + * @brief Check if the USART Error Interrupt is enabled or disabled. + * @rmtoll CR3 EIE LL_USART_IsEnabledIT_ERROR + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIT_ERROR(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_EIE) == (USART_CR3_EIE)); +} + +/** + * @brief Check if the USART CTS Interrupt is enabled or disabled. + * @note Macro @ref IS_UART_HWFLOW_INSTANCE(USARTx) can be used to check whether or not + * Hardware Flow control feature is supported by the USARTx instance. + * @rmtoll CR3 CTSIE LL_USART_IsEnabledIT_CTS + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledIT_CTS(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_CTSIE) == (USART_CR3_CTSIE)); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_DMA_Management DMA_Management + * @{ + */ + +/** + * @brief Enable DMA Mode for reception + * @rmtoll CR3 DMAR LL_USART_EnableDMAReq_RX + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableDMAReq_RX(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_DMAR); +} + +/** + * @brief Disable DMA Mode for reception + * @rmtoll CR3 DMAR LL_USART_DisableDMAReq_RX + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableDMAReq_RX(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_DMAR); +} + +/** + * @brief Check if DMA Mode is enabled for reception + * @rmtoll CR3 DMAR LL_USART_IsEnabledDMAReq_RX + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledDMAReq_RX(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_DMAR) == (USART_CR3_DMAR)); +} + +/** + * @brief Enable DMA Mode for transmission + * @rmtoll CR3 DMAT LL_USART_EnableDMAReq_TX + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_EnableDMAReq_TX(USART_TypeDef *USARTx) +{ + ATOMIC_SET_BIT(USARTx->CR3, USART_CR3_DMAT); +} + +/** + * @brief Disable DMA Mode for transmission + * @rmtoll CR3 DMAT LL_USART_DisableDMAReq_TX + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_DisableDMAReq_TX(USART_TypeDef *USARTx) +{ + ATOMIC_CLEAR_BIT(USARTx->CR3, USART_CR3_DMAT); +} + +/** + * @brief Check if DMA Mode is enabled for transmission + * @rmtoll CR3 DMAT LL_USART_IsEnabledDMAReq_TX + * @param USARTx USART Instance + * @retval State of bit (1 or 0). + */ +__STATIC_INLINE uint32_t LL_USART_IsEnabledDMAReq_TX(USART_TypeDef *USARTx) +{ + return (READ_BIT(USARTx->CR3, USART_CR3_DMAT) == (USART_CR3_DMAT)); +} + +/** + * @brief Get the data register address used for DMA transfer + * @rmtoll DR DR LL_USART_DMA_GetRegAddr + * @note Address of Data Register is valid for both Transmit and Receive transfers. + * @param USARTx USART Instance + * @retval Address of data register + */ +__STATIC_INLINE uint32_t LL_USART_DMA_GetRegAddr(USART_TypeDef *USARTx) +{ + /* return address of DR register */ + return ((uint32_t) &(USARTx->DR)); +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_Data_Management Data_Management + * @{ + */ + +/** + * @brief Read Receiver Data register (Receive Data value, 8 bits) + * @rmtoll DR DR LL_USART_ReceiveData8 + * @param USARTx USART Instance + * @retval Value between Min_Data=0x00 and Max_Data=0xFF + */ +__STATIC_INLINE uint8_t LL_USART_ReceiveData8(USART_TypeDef *USARTx) +{ + return (uint8_t)(READ_BIT(USARTx->DR, USART_DR_DR)); +} + +/** + * @brief Read Receiver Data register (Receive Data value, 9 bits) + * @rmtoll DR DR LL_USART_ReceiveData9 + * @param USARTx USART Instance + * @retval Value between Min_Data=0x00 and Max_Data=0x1FF + */ +__STATIC_INLINE uint16_t LL_USART_ReceiveData9(USART_TypeDef *USARTx) +{ + return (uint16_t)(READ_BIT(USARTx->DR, USART_DR_DR)); +} + +/** + * @brief Write in Transmitter Data Register (Transmit Data value, 8 bits) + * @rmtoll DR DR LL_USART_TransmitData8 + * @param USARTx USART Instance + * @param Value between Min_Data=0x00 and Max_Data=0xFF + * @retval None + */ +__STATIC_INLINE void LL_USART_TransmitData8(USART_TypeDef *USARTx, uint8_t Value) +{ + USARTx->DR = Value; +} + +/** + * @brief Write in Transmitter Data Register (Transmit Data value, 9 bits) + * @rmtoll DR DR LL_USART_TransmitData9 + * @param USARTx USART Instance + * @param Value between Min_Data=0x00 and Max_Data=0x1FF + * @retval None + */ +__STATIC_INLINE void LL_USART_TransmitData9(USART_TypeDef *USARTx, uint16_t Value) +{ + USARTx->DR = Value & 0x1FFU; +} + +/** + * @} + */ + +/** @defgroup USART_LL_EF_Execution Execution + * @{ + */ + +/** + * @brief Request Break sending + * @rmtoll CR1 SBK LL_USART_RequestBreakSending + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_RequestBreakSending(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR1, USART_CR1_SBK); +} + +/** + * @brief Put USART in Mute mode + * @rmtoll CR1 RWU LL_USART_RequestEnterMuteMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_RequestEnterMuteMode(USART_TypeDef *USARTx) +{ + SET_BIT(USARTx->CR1, USART_CR1_RWU); +} + +/** + * @brief Put USART in Active mode + * @rmtoll CR1 RWU LL_USART_RequestExitMuteMode + * @param USARTx USART Instance + * @retval None + */ +__STATIC_INLINE void LL_USART_RequestExitMuteMode(USART_TypeDef *USARTx) +{ + CLEAR_BIT(USARTx->CR1, USART_CR1_RWU); +} + +/** + * @} + */ + +#if defined(USE_FULL_LL_DRIVER) +/** @defgroup USART_LL_EF_Init Initialization and de-initialization functions + * @{ + */ +ErrorStatus LL_USART_DeInit(USART_TypeDef *USARTx); +ErrorStatus LL_USART_Init(USART_TypeDef *USARTx, LL_USART_InitTypeDef *USART_InitStruct); +void LL_USART_StructInit(LL_USART_InitTypeDef *USART_InitStruct); +ErrorStatus LL_USART_ClockInit(USART_TypeDef *USARTx, LL_USART_ClockInitTypeDef *USART_ClockInitStruct); +void LL_USART_ClockStructInit(LL_USART_ClockInitTypeDef *USART_ClockInitStruct); +/** + * @} + */ +#endif /* USE_FULL_LL_DRIVER */ + +/** + * @} + */ + +/** + * @} + */ + +#endif /* USART1 || USART2 || USART3 || USART6 || UART4 || UART5 || UART7 || UART8 || UART9 || UART10 */ + +/** + * @} + */ + +#ifdef __cplusplus +} +#endif + +#endif /* __STM32F4xx_LL_USART_H */ + diff --git a/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c b/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c new file mode 100644 index 00000000..d958ad64 --- /dev/null +++ b/Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c @@ -0,0 +1,3751 @@ +/** + ****************************************************************************** + * @file stm32f4xx_hal_uart.c + * @author MCD Application Team + * @brief UART HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the Universal Asynchronous Receiver Transmitter Peripheral (UART). + * + Initialization and de-initialization functions + * + IO operation functions + * + Peripheral Control functions + * + Peripheral State and Errors functions + * + ****************************************************************************** + * @attention + * + * Copyright (c) 2016 STMicroelectronics. + * All rights reserved. + * + * This software is licensed under terms that can be found in the LICENSE file + * in the root directory of this software component. + * If no LICENSE file comes with this software, it is provided AS-IS. + * + ****************************************************************************** + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] + The UART HAL driver can be used as follows: + + (#) Declare a UART_HandleTypeDef handle structure (eg. UART_HandleTypeDef huart). + (#) Initialize the UART low level resources by implementing the HAL_UART_MspInit() API: + (##) Enable the USARTx interface clock. + (##) UART pins configuration: + (+++) Enable the clock for the UART GPIOs. + (+++) Configure the UART TX/RX pins as alternate function pull-up. + (##) NVIC configuration if you need to use interrupt process (HAL_UART_Transmit_IT() + and HAL_UART_Receive_IT() APIs): + (+++) Configure the USARTx interrupt priority. + (+++) Enable the NVIC USART IRQ handle. + (##) DMA Configuration if you need to use DMA process (HAL_UART_Transmit_DMA() + and HAL_UART_Receive_DMA() APIs): + (+++) Declare a DMA handle structure for the Tx/Rx stream. + (+++) Enable the DMAx interface clock. + (+++) Configure the declared DMA handle structure with the required + Tx/Rx parameters. + (+++) Configure the DMA Tx/Rx stream. + (+++) Associate the initialized DMA handle to the UART DMA Tx/Rx handle. + (+++) Configure the priority and enable the NVIC for the transfer complete + interrupt on the DMA Tx/Rx stream. + (+++) Configure the USARTx interrupt priority and enable the NVIC USART IRQ handle + (used for last byte sending completion detection in DMA non circular mode) + + (#) Program the Baud Rate, Word Length, Stop Bit, Parity, Hardware + flow control and Mode(Receiver/Transmitter) in the huart Init structure. + + (#) For the UART asynchronous mode, initialize the UART registers by calling + the HAL_UART_Init() API. + + (#) For the UART Half duplex mode, initialize the UART registers by calling + the HAL_HalfDuplex_Init() API. + + (#) For the LIN mode, initialize the UART registers by calling the HAL_LIN_Init() API. + + (#) For the Multi-Processor mode, initialize the UART registers by calling + the HAL_MultiProcessor_Init() API. + + [..] + (@) The specific UART interrupts (Transmission complete interrupt, + RXNE interrupt and Error Interrupts) will be managed using the macros + __HAL_UART_ENABLE_IT() and __HAL_UART_DISABLE_IT() inside the transmit + and receive process. + + [..] + (@) These APIs (HAL_UART_Init() and HAL_HalfDuplex_Init()) configure also the + low level Hardware GPIO, CLOCK, CORTEX...etc) by calling the customized + HAL_UART_MspInit() API. + + ##### Callback registration ##### + ================================== + + [..] + The compilation define USE_HAL_UART_REGISTER_CALLBACKS when set to 1 + allows the user to configure dynamically the driver callbacks. + + [..] + Use Function HAL_UART_RegisterCallback() to register a user callback. + Function HAL_UART_RegisterCallback() allows to register following callbacks: + (+) TxHalfCpltCallback : Tx Half Complete Callback. + (+) TxCpltCallback : Tx Complete Callback. + (+) RxHalfCpltCallback : Rx Half Complete Callback. + (+) RxCpltCallback : Rx Complete Callback. + (+) ErrorCallback : Error Callback. + (+) AbortCpltCallback : Abort Complete Callback. + (+) AbortTransmitCpltCallback : Abort Transmit Complete Callback. + (+) AbortReceiveCpltCallback : Abort Receive Complete Callback. + (+) MspInitCallback : UART MspInit. + (+) MspDeInitCallback : UART MspDeInit. + This function takes as parameters the HAL peripheral handle, the Callback ID + and a pointer to the user callback function. + + [..] + Use function HAL_UART_UnRegisterCallback() to reset a callback to the default + weak (surcharged) function. + HAL_UART_UnRegisterCallback() takes as parameters the HAL peripheral handle, + and the Callback ID. + This function allows to reset following callbacks: + (+) TxHalfCpltCallback : Tx Half Complete Callback. + (+) TxCpltCallback : Tx Complete Callback. + (+) RxHalfCpltCallback : Rx Half Complete Callback. + (+) RxCpltCallback : Rx Complete Callback. + (+) ErrorCallback : Error Callback. + (+) AbortCpltCallback : Abort Complete Callback. + (+) AbortTransmitCpltCallback : Abort Transmit Complete Callback. + (+) AbortReceiveCpltCallback : Abort Receive Complete Callback. + (+) MspInitCallback : UART MspInit. + (+) MspDeInitCallback : UART MspDeInit. + + [..] + For specific callback RxEventCallback, use dedicated registration/reset functions: + respectively HAL_UART_RegisterRxEventCallback() , HAL_UART_UnRegisterRxEventCallback(). + + [..] + By default, after the HAL_UART_Init() and when the state is HAL_UART_STATE_RESET + all callbacks are set to the corresponding weak (surcharged) functions: + examples HAL_UART_TxCpltCallback(), HAL_UART_RxHalfCpltCallback(). + Exception done for MspInit and MspDeInit functions that are respectively + reset to the legacy weak (surcharged) functions in the HAL_UART_Init() + and HAL_UART_DeInit() only when these callbacks are null (not registered beforehand). + If not, MspInit or MspDeInit are not null, the HAL_UART_Init() and HAL_UART_DeInit() + keep and use the user MspInit/MspDeInit callbacks (registered beforehand). + + [..] + Callbacks can be registered/unregistered in HAL_UART_STATE_READY state only. + Exception done MspInit/MspDeInit that can be registered/unregistered + in HAL_UART_STATE_READY or HAL_UART_STATE_RESET state, thus registered (user) + MspInit/DeInit callbacks can be used during the Init/DeInit. + In that case first register the MspInit/MspDeInit user callbacks + using HAL_UART_RegisterCallback() before calling HAL_UART_DeInit() + or HAL_UART_Init() function. + + [..] + When The compilation define USE_HAL_UART_REGISTER_CALLBACKS is set to 0 or + not defined, the callback registration feature is not available + and weak (surcharged) callbacks are used. + + [..] + Three operation modes are available within this driver : + + *** Polling mode IO operation *** + ================================= + [..] + (+) Send an amount of data in blocking mode using HAL_UART_Transmit() + (+) Receive an amount of data in blocking mode using HAL_UART_Receive() + + *** Interrupt mode IO operation *** + =================================== + [..] + (+) Send an amount of data in non blocking mode using HAL_UART_Transmit_IT() + (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxCpltCallback + (+) Receive an amount of data in non blocking mode using HAL_UART_Receive_IT() + (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxCpltCallback + (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_UART_ErrorCallback + + *** DMA mode IO operation *** + ============================== + [..] + (+) Send an amount of data in non blocking mode (DMA) using HAL_UART_Transmit_DMA() + (+) At transmission end of half transfer HAL_UART_TxHalfCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxHalfCpltCallback + (+) At transmission end of transfer HAL_UART_TxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_TxCpltCallback + (+) Receive an amount of data in non blocking mode (DMA) using HAL_UART_Receive_DMA() + (+) At reception end of half transfer HAL_UART_RxHalfCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxHalfCpltCallback + (+) At reception end of transfer HAL_UART_RxCpltCallback is executed and user can + add his own code by customization of function pointer HAL_UART_RxCpltCallback + (+) In case of transfer Error, HAL_UART_ErrorCallback() function is executed and user can + add his own code by customization of function pointer HAL_UART_ErrorCallback + (+) Pause the DMA Transfer using HAL_UART_DMAPause() + (+) Resume the DMA Transfer using HAL_UART_DMAResume() + (+) Stop the DMA Transfer using HAL_UART_DMAStop() + + + [..] This subsection also provides a set of additional functions providing enhanced reception + services to user. (For example, these functions allow application to handle use cases + where number of data to be received is unknown). + + (#) Compared to standard reception services which only consider number of received + data elements as reception completion criteria, these functions also consider additional events + as triggers for updating reception status to caller : + (+) Detection of inactivity period (RX line has not been active for a given period). + (++) RX inactivity detected by IDLE event, i.e. RX line has been in idle state (normally high state) + for 1 frame time, after last received byte. + + (#) There are two mode of transfer: + (+) Blocking mode: The reception is performed in polling mode, until either expected number of data is received, + or till IDLE event occurs. Reception is handled only during function execution. + When function exits, no data reception could occur. HAL status and number of actually received data elements, + are returned by function after finishing transfer. + (+) Non-Blocking mode: The reception is performed using Interrupts or DMA. + These API's return the HAL status. + The end of the data processing will be indicated through the + dedicated UART IRQ when using Interrupt mode or the DMA IRQ when using DMA mode. + The HAL_UARTEx_RxEventCallback() user callback will be executed during Receive process + The HAL_UART_ErrorCallback()user callback will be executed when a reception error is detected. + + (#) Blocking mode API: + (+) HAL_UARTEx_ReceiveToIdle() + + (#) Non-Blocking mode API with Interrupt: + (+) HAL_UARTEx_ReceiveToIdle_IT() + + (#) Non-Blocking mode API with DMA: + (+) HAL_UARTEx_ReceiveToIdle_DMA() + + + *** UART HAL driver macros list *** + ============================================= + [..] + Below the list of most used macros in UART HAL driver. + + (+) __HAL_UART_ENABLE: Enable the UART peripheral + (+) __HAL_UART_DISABLE: Disable the UART peripheral + (+) __HAL_UART_GET_FLAG : Check whether the specified UART flag is set or not + (+) __HAL_UART_CLEAR_FLAG : Clear the specified UART pending flag + (+) __HAL_UART_ENABLE_IT: Enable the specified UART interrupt + (+) __HAL_UART_DISABLE_IT: Disable the specified UART interrupt + (+) __HAL_UART_GET_IT_SOURCE: Check whether the specified UART interrupt has occurred or not + + [..] + (@) You can refer to the UART HAL driver header file for more useful macros + + @endverbatim + [..] + (@) Additional remark: If the parity is enabled, then the MSB bit of the data written + in the data register is transmitted but is changed by the parity bit. + Depending on the frame length defined by the M bit (8-bits or 9-bits), + the possible UART frame formats are as listed in the following table: + +-------------------------------------------------------------+ + | M bit | PCE bit | UART frame | + |---------------------|---------------------------------------| + | 0 | 0 | | SB | 8 bit data | STB | | + |---------|-----------|---------------------------------------| + | 0 | 1 | | SB | 7 bit data | PB | STB | | + |---------|-----------|---------------------------------------| + | 1 | 0 | | SB | 9 bit data | STB | | + |---------|-----------|---------------------------------------| + | 1 | 1 | | SB | 8 bit data | PB | STB | | + +-------------------------------------------------------------+ + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32f4xx_hal.h" + +/** @addtogroup STM32F4xx_HAL_Driver + * @{ + */ + +/** @defgroup UART UART + * @brief HAL UART module driver + * @{ + */ +#ifdef HAL_UART_MODULE_ENABLED + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @addtogroup UART_Private_Constants + * @{ + */ +/** + * @} + */ +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/** @addtogroup UART_Private_Functions UART Private Functions + * @{ + */ + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) +void UART_InitCallbacksToDefault(UART_HandleTypeDef *huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +static void UART_EndTxTransfer(UART_HandleTypeDef *huart); +static void UART_EndRxTransfer(UART_HandleTypeDef *huart); +static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma); +static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma); +static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma); +static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma); +static void UART_DMAError(DMA_HandleTypeDef *hdma); +static void UART_DMAAbortOnError(DMA_HandleTypeDef *hdma); +static void UART_DMATxAbortCallback(DMA_HandleTypeDef *hdma); +static void UART_DMARxAbortCallback(DMA_HandleTypeDef *hdma); +static void UART_DMATxOnlyAbortCallback(DMA_HandleTypeDef *hdma); +static void UART_DMARxOnlyAbortCallback(DMA_HandleTypeDef *hdma); +static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart); +static HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, + uint32_t Tickstart, uint32_t Timeout); +static void UART_SetConfig(UART_HandleTypeDef *huart); + +/** + * @} + */ + +/* Exported functions ---------------------------------------------------------*/ +/** @defgroup UART_Exported_Functions UART Exported Functions + * @{ + */ + +/** @defgroup UART_Exported_Functions_Group1 Initialization and de-initialization functions + * @brief Initialization and Configuration functions + * +@verbatim + =============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to initialize the USARTx or the UARTy + in asynchronous mode. + (+) For the asynchronous mode only these parameters can be configured: + (++) Baud Rate + (++) Word Length + (++) Stop Bit + (++) Parity: If the parity is enabled, then the MSB bit of the data written + in the data register is transmitted but is changed by the parity bit. + Depending on the frame length defined by the M bit (8-bits or 9-bits), + please refer to Reference manual for possible UART frame formats. + (++) Hardware flow control + (++) Receiver/transmitter modes + (++) Over Sampling Method + [..] + The HAL_UART_Init(), HAL_HalfDuplex_Init(), HAL_LIN_Init() and HAL_MultiProcessor_Init() APIs + follow respectively the UART asynchronous, UART Half duplex, LIN and Multi-Processor configuration + procedures (details for the procedures are available in reference manual + (RM0430 for STM32F4X3xx MCUs and RM0402 for STM32F412xx MCUs + RM0383 for STM32F411xC/E MCUs and RM0401 for STM32F410xx MCUs + RM0090 for STM32F4X5xx/STM32F4X7xx/STM32F429xx/STM32F439xx MCUs + RM0390 for STM32F446xx MCUs and RM0386 for STM32F469xx/STM32F479xx MCUs)). + +@endverbatim + * @{ + */ + +/** + * @brief Initializes the UART mode according to the specified parameters in + * the UART_InitTypeDef and create the associated handle. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if (huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + if (huart->Init.HwFlowCtl != UART_HWCONTROL_NONE) + { + /* The hardware flow control is available only for USART1, USART2, USART3 and USART6. + Except for STM32F446xx devices, that is available for USART1, USART2, USART3, USART6, UART4 and UART5. + */ + assert_param(IS_UART_HWFLOW_INSTANCE(huart->Instance)); + assert_param(IS_UART_HARDWARE_FLOW_CONTROL(huart->Init.HwFlowCtl)); + } + else + { + assert_param(IS_UART_INSTANCE(huart->Instance)); + } + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if (huart->gState == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + UART_InitCallbacksToDefault(huart); + + if (huart->MspInitCallback == NULL) + { + huart->MspInitCallback = HAL_UART_MspInit; + } + + /* Init the low level hardware */ + huart->MspInitCallback(huart); +#else + /* Init the low level hardware : GPIO, CLOCK */ + HAL_UART_MspInit(huart); +#endif /* (USE_HAL_UART_REGISTER_CALLBACKS) */ + } + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In asynchronous mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN)); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the half-duplex mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if (huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_HALFDUPLEX_INSTANCE(huart->Instance)); + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if (huart->gState == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + UART_InitCallbacksToDefault(huart); + + if (huart->MspInitCallback == NULL) + { + huart->MspInitCallback = HAL_UART_MspInit; + } + + /* Init the low level hardware */ + huart->MspInitCallback(huart); +#else + /* Init the low level hardware : GPIO, CLOCK */ + HAL_UART_MspInit(huart); +#endif /* (USE_HAL_UART_REGISTER_CALLBACKS) */ + } + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In half-duplex mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_IREN | USART_CR3_SCEN)); + + /* Enable the Half-Duplex mode by setting the HDSEL bit in the CR3 register */ + SET_BIT(huart->Instance->CR3, USART_CR3_HDSEL); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state*/ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the LIN mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param BreakDetectLength Specifies the LIN break detection length. + * This parameter can be one of the following values: + * @arg UART_LINBREAKDETECTLENGTH_10B: 10-bit break detection + * @arg UART_LINBREAKDETECTLENGTH_11B: 11-bit break detection + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LIN_Init(UART_HandleTypeDef *huart, uint32_t BreakDetectLength) +{ + /* Check the UART handle allocation */ + if (huart == NULL) + { + return HAL_ERROR; + } + + /* Check the LIN UART instance */ + assert_param(IS_UART_LIN_INSTANCE(huart->Instance)); + + /* Check the Break detection length parameter */ + assert_param(IS_UART_LIN_BREAK_DETECT_LENGTH(BreakDetectLength)); + assert_param(IS_UART_LIN_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_LIN_OVERSAMPLING(huart->Init.OverSampling)); + + if (huart->gState == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + UART_InitCallbacksToDefault(huart); + + if (huart->MspInitCallback == NULL) + { + huart->MspInitCallback = HAL_UART_MspInit; + } + + /* Init the low level hardware */ + huart->MspInitCallback(huart); +#else + /* Init the low level hardware : GPIO, CLOCK */ + HAL_UART_MspInit(huart); +#endif /* (USE_HAL_UART_REGISTER_CALLBACKS) */ + } + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In LIN mode, the following bits must be kept cleared: + - CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register.*/ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_HDSEL | USART_CR3_IREN | USART_CR3_SCEN)); + + /* Enable the LIN mode by setting the LINEN bit in the CR2 register */ + SET_BIT(huart->Instance->CR2, USART_CR2_LINEN); + + /* Set the USART LIN Break detection length. */ + CLEAR_BIT(huart->Instance->CR2, USART_CR2_LBDL); + SET_BIT(huart->Instance->CR2, BreakDetectLength); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state*/ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Initializes the Multi-Processor mode according to the specified + * parameters in the UART_InitTypeDef and create the associated handle. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param Address USART address + * @param WakeUpMethod specifies the USART wake-up method. + * This parameter can be one of the following values: + * @arg UART_WAKEUPMETHOD_IDLELINE: Wake-up by an idle line detection + * @arg UART_WAKEUPMETHOD_ADDRESSMARK: Wake-up by an address mark + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod) +{ + /* Check the UART handle allocation */ + if (huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Check the Address & wake up method parameters */ + assert_param(IS_UART_WAKEUPMETHOD(WakeUpMethod)); + assert_param(IS_UART_ADDRESS(Address)); + assert_param(IS_UART_WORD_LENGTH(huart->Init.WordLength)); + assert_param(IS_UART_OVERSAMPLING(huart->Init.OverSampling)); + + if (huart->gState == HAL_UART_STATE_RESET) + { + /* Allocate lock resource and initialize it */ + huart->Lock = HAL_UNLOCKED; + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + UART_InitCallbacksToDefault(huart); + + if (huart->MspInitCallback == NULL) + { + huart->MspInitCallback = HAL_UART_MspInit; + } + + /* Init the low level hardware */ + huart->MspInitCallback(huart); +#else + /* Init the low level hardware : GPIO, CLOCK */ + HAL_UART_MspInit(huart); +#endif /* (USE_HAL_UART_REGISTER_CALLBACKS) */ + } + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_UART_DISABLE(huart); + + /* Set the UART Communication parameters */ + UART_SetConfig(huart); + + /* In Multi-Processor mode, the following bits must be kept cleared: + - LINEN and CLKEN bits in the USART_CR2 register, + - SCEN, HDSEL and IREN bits in the USART_CR3 register */ + CLEAR_BIT(huart->Instance->CR2, (USART_CR2_LINEN | USART_CR2_CLKEN)); + CLEAR_BIT(huart->Instance->CR3, (USART_CR3_SCEN | USART_CR3_HDSEL | USART_CR3_IREN)); + + /* Set the USART address node */ + CLEAR_BIT(huart->Instance->CR2, USART_CR2_ADD); + SET_BIT(huart->Instance->CR2, Address); + + /* Set the wake up method by setting the WAKE bit in the CR1 register */ + CLEAR_BIT(huart->Instance->CR1, USART_CR1_WAKE); + SET_BIT(huart->Instance->CR1, WakeUpMethod); + + /* Enable the peripheral */ + __HAL_UART_ENABLE(huart); + + /* Initialize the UART state */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief DeInitializes the UART peripheral. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DeInit(UART_HandleTypeDef *huart) +{ + /* Check the UART handle allocation */ + if (huart == NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the Peripheral */ + __HAL_UART_DISABLE(huart); + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + if (huart->MspDeInitCallback == NULL) + { + huart->MspDeInitCallback = HAL_UART_MspDeInit; + } + /* DeInit the low level hardware */ + huart->MspDeInitCallback(huart); +#else + /* DeInit the low level hardware */ + HAL_UART_MspDeInit(huart); +#endif /* (USE_HAL_UART_REGISTER_CALLBACKS) */ + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_RESET; + huart->RxState = HAL_UART_STATE_RESET; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* Process Unlock */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief UART MSP Init. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_MspInit(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_MspInit could be implemented in the user file + */ +} + +/** + * @brief UART MSP DeInit. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_MspDeInit(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_MspDeInit could be implemented in the user file + */ +} + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) +/** + * @brief Register a User UART Callback + * To be used instead of the weak predefined callback + * @param huart uart handle + * @param CallbackID ID of the callback to be registered + * This parameter can be one of the following values: + * @arg @ref HAL_UART_TX_HALFCOMPLETE_CB_ID Tx Half Complete Callback ID + * @arg @ref HAL_UART_TX_COMPLETE_CB_ID Tx Complete Callback ID + * @arg @ref HAL_UART_RX_HALFCOMPLETE_CB_ID Rx Half Complete Callback ID + * @arg @ref HAL_UART_RX_COMPLETE_CB_ID Rx Complete Callback ID + * @arg @ref HAL_UART_ERROR_CB_ID Error Callback ID + * @arg @ref HAL_UART_ABORT_COMPLETE_CB_ID Abort Complete Callback ID + * @arg @ref HAL_UART_ABORT_TRANSMIT_COMPLETE_CB_ID Abort Transmit Complete Callback ID + * @arg @ref HAL_UART_ABORT_RECEIVE_COMPLETE_CB_ID Abort Receive Complete Callback ID + * @arg @ref HAL_UART_MSPINIT_CB_ID MspInit Callback ID + * @arg @ref HAL_UART_MSPDEINIT_CB_ID MspDeInit Callback ID + * @param pCallback pointer to the Callback function + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_RegisterCallback(UART_HandleTypeDef *huart, HAL_UART_CallbackIDTypeDef CallbackID, + pUART_CallbackTypeDef pCallback) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (pCallback == NULL) + { + /* Update the error code */ + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + return HAL_ERROR; + } + /* Process locked */ + __HAL_LOCK(huart); + + if (huart->gState == HAL_UART_STATE_READY) + { + switch (CallbackID) + { + case HAL_UART_TX_HALFCOMPLETE_CB_ID : + huart->TxHalfCpltCallback = pCallback; + break; + + case HAL_UART_TX_COMPLETE_CB_ID : + huart->TxCpltCallback = pCallback; + break; + + case HAL_UART_RX_HALFCOMPLETE_CB_ID : + huart->RxHalfCpltCallback = pCallback; + break; + + case HAL_UART_RX_COMPLETE_CB_ID : + huart->RxCpltCallback = pCallback; + break; + + case HAL_UART_ERROR_CB_ID : + huart->ErrorCallback = pCallback; + break; + + case HAL_UART_ABORT_COMPLETE_CB_ID : + huart->AbortCpltCallback = pCallback; + break; + + case HAL_UART_ABORT_TRANSMIT_COMPLETE_CB_ID : + huart->AbortTransmitCpltCallback = pCallback; + break; + + case HAL_UART_ABORT_RECEIVE_COMPLETE_CB_ID : + huart->AbortReceiveCpltCallback = pCallback; + break; + + case HAL_UART_MSPINIT_CB_ID : + huart->MspInitCallback = pCallback; + break; + + case HAL_UART_MSPDEINIT_CB_ID : + huart->MspDeInitCallback = pCallback; + break; + + default : + /* Update the error code */ + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else if (huart->gState == HAL_UART_STATE_RESET) + { + switch (CallbackID) + { + case HAL_UART_MSPINIT_CB_ID : + huart->MspInitCallback = pCallback; + break; + + case HAL_UART_MSPDEINIT_CB_ID : + huart->MspDeInitCallback = pCallback; + break; + + default : + /* Update the error code */ + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else + { + /* Update the error code */ + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + } + + /* Release Lock */ + __HAL_UNLOCK(huart); + + return status; +} + +/** + * @brief Unregister an UART Callback + * UART callaback is redirected to the weak predefined callback + * @param huart uart handle + * @param CallbackID ID of the callback to be unregistered + * This parameter can be one of the following values: + * @arg @ref HAL_UART_TX_HALFCOMPLETE_CB_ID Tx Half Complete Callback ID + * @arg @ref HAL_UART_TX_COMPLETE_CB_ID Tx Complete Callback ID + * @arg @ref HAL_UART_RX_HALFCOMPLETE_CB_ID Rx Half Complete Callback ID + * @arg @ref HAL_UART_RX_COMPLETE_CB_ID Rx Complete Callback ID + * @arg @ref HAL_UART_ERROR_CB_ID Error Callback ID + * @arg @ref HAL_UART_ABORT_COMPLETE_CB_ID Abort Complete Callback ID + * @arg @ref HAL_UART_ABORT_TRANSMIT_COMPLETE_CB_ID Abort Transmit Complete Callback ID + * @arg @ref HAL_UART_ABORT_RECEIVE_COMPLETE_CB_ID Abort Receive Complete Callback ID + * @arg @ref HAL_UART_MSPINIT_CB_ID MspInit Callback ID + * @arg @ref HAL_UART_MSPDEINIT_CB_ID MspDeInit Callback ID + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_UnRegisterCallback(UART_HandleTypeDef *huart, HAL_UART_CallbackIDTypeDef CallbackID) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Process locked */ + __HAL_LOCK(huart); + + if (HAL_UART_STATE_READY == huart->gState) + { + switch (CallbackID) + { + case HAL_UART_TX_HALFCOMPLETE_CB_ID : + huart->TxHalfCpltCallback = HAL_UART_TxHalfCpltCallback; /* Legacy weak TxHalfCpltCallback */ + break; + + case HAL_UART_TX_COMPLETE_CB_ID : + huart->TxCpltCallback = HAL_UART_TxCpltCallback; /* Legacy weak TxCpltCallback */ + break; + + case HAL_UART_RX_HALFCOMPLETE_CB_ID : + huart->RxHalfCpltCallback = HAL_UART_RxHalfCpltCallback; /* Legacy weak RxHalfCpltCallback */ + break; + + case HAL_UART_RX_COMPLETE_CB_ID : + huart->RxCpltCallback = HAL_UART_RxCpltCallback; /* Legacy weak RxCpltCallback */ + break; + + case HAL_UART_ERROR_CB_ID : + huart->ErrorCallback = HAL_UART_ErrorCallback; /* Legacy weak ErrorCallback */ + break; + + case HAL_UART_ABORT_COMPLETE_CB_ID : + huart->AbortCpltCallback = HAL_UART_AbortCpltCallback; /* Legacy weak AbortCpltCallback */ + break; + + case HAL_UART_ABORT_TRANSMIT_COMPLETE_CB_ID : + huart->AbortTransmitCpltCallback = HAL_UART_AbortTransmitCpltCallback; /* Legacy weak AbortTransmitCpltCallback */ + break; + + case HAL_UART_ABORT_RECEIVE_COMPLETE_CB_ID : + huart->AbortReceiveCpltCallback = HAL_UART_AbortReceiveCpltCallback; /* Legacy weak AbortReceiveCpltCallback */ + break; + + case HAL_UART_MSPINIT_CB_ID : + huart->MspInitCallback = HAL_UART_MspInit; /* Legacy weak MspInitCallback */ + break; + + case HAL_UART_MSPDEINIT_CB_ID : + huart->MspDeInitCallback = HAL_UART_MspDeInit; /* Legacy weak MspDeInitCallback */ + break; + + default : + /* Update the error code */ + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else if (HAL_UART_STATE_RESET == huart->gState) + { + switch (CallbackID) + { + case HAL_UART_MSPINIT_CB_ID : + huart->MspInitCallback = HAL_UART_MspInit; + break; + + case HAL_UART_MSPDEINIT_CB_ID : + huart->MspDeInitCallback = HAL_UART_MspDeInit; + break; + + default : + /* Update the error code */ + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + break; + } + } + else + { + /* Update the error code */ + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + /* Return error status */ + status = HAL_ERROR; + } + + /* Release Lock */ + __HAL_UNLOCK(huart); + + return status; +} + +/** + * @brief Register a User UART Rx Event Callback + * To be used instead of the weak predefined callback + * @param huart Uart handle + * @param pCallback Pointer to the Rx Event Callback function + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_RegisterRxEventCallback(UART_HandleTypeDef *huart, pUART_RxEventCallbackTypeDef pCallback) +{ + HAL_StatusTypeDef status = HAL_OK; + + if (pCallback == NULL) + { + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + return HAL_ERROR; + } + + /* Process locked */ + __HAL_LOCK(huart); + + if (huart->gState == HAL_UART_STATE_READY) + { + huart->RxEventCallback = pCallback; + } + else + { + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + status = HAL_ERROR; + } + + /* Release Lock */ + __HAL_UNLOCK(huart); + + return status; +} + +/** + * @brief UnRegister the UART Rx Event Callback + * UART Rx Event Callback is redirected to the weak HAL_UARTEx_RxEventCallback() predefined callback + * @param huart Uart handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_UnRegisterRxEventCallback(UART_HandleTypeDef *huart) +{ + HAL_StatusTypeDef status = HAL_OK; + + /* Process locked */ + __HAL_LOCK(huart); + + if (huart->gState == HAL_UART_STATE_READY) + { + huart->RxEventCallback = HAL_UARTEx_RxEventCallback; /* Legacy weak UART Rx Event Callback */ + } + else + { + huart->ErrorCode |= HAL_UART_ERROR_INVALID_CALLBACK; + + status = HAL_ERROR; + } + + /* Release Lock */ + __HAL_UNLOCK(huart); + return status; +} +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group2 IO operation functions + * @brief UART Transmit and Receive functions + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + This subsection provides a set of functions allowing to manage the UART asynchronous + and Half duplex data transfers. + + (#) There are two modes of transfer: + (+) Blocking mode: The communication is performed in polling mode. + The HAL status of all data processing is returned by the same function + after finishing transfer. + (+) Non-Blocking mode: The communication is performed using Interrupts + or DMA, these API's return the HAL status. + The end of the data processing will be indicated through the + dedicated UART IRQ when using Interrupt mode or the DMA IRQ when + using DMA mode. + The HAL_UART_TxCpltCallback(), HAL_UART_RxCpltCallback() user callbacks + will be executed respectively at the end of the transmit or receive process + The HAL_UART_ErrorCallback()user callback will be executed when a communication error is detected. + + (#) Blocking mode API's are : + (+) HAL_UART_Transmit() + (+) HAL_UART_Receive() + + (#) Non-Blocking mode API's with Interrupt are : + (+) HAL_UART_Transmit_IT() + (+) HAL_UART_Receive_IT() + (+) HAL_UART_IRQHandler() + + (#) Non-Blocking mode API's with DMA are : + (+) HAL_UART_Transmit_DMA() + (+) HAL_UART_Receive_DMA() + (+) HAL_UART_DMAPause() + (+) HAL_UART_DMAResume() + (+) HAL_UART_DMAStop() + + (#) A set of Transfer Complete Callbacks are provided in Non_Blocking mode: + (+) HAL_UART_TxHalfCpltCallback() + (+) HAL_UART_TxCpltCallback() + (+) HAL_UART_RxHalfCpltCallback() + (+) HAL_UART_RxCpltCallback() + (+) HAL_UART_ErrorCallback() + + (#) Non-Blocking mode transfers could be aborted using Abort API's : + (+) HAL_UART_Abort() + (+) HAL_UART_AbortTransmit() + (+) HAL_UART_AbortReceive() + (+) HAL_UART_Abort_IT() + (+) HAL_UART_AbortTransmit_IT() + (+) HAL_UART_AbortReceive_IT() + + (#) For Abort services based on interrupts (HAL_UART_Abortxxx_IT), a set of Abort Complete Callbacks are provided: + (+) HAL_UART_AbortCpltCallback() + (+) HAL_UART_AbortTransmitCpltCallback() + (+) HAL_UART_AbortReceiveCpltCallback() + + (#) A Rx Event Reception Callback (Rx event notification) is available for Non_Blocking modes of enhanced reception services: + (+) HAL_UARTEx_RxEventCallback() + + (#) In Non-Blocking mode transfers, possible errors are split into 2 categories. + Errors are handled as follows : + (+) Error is considered as Recoverable and non blocking : Transfer could go till end, but error severity is + to be evaluated by user : this concerns Frame Error, Parity Error or Noise Error in Interrupt mode reception . + Received character is then retrieved and stored in Rx buffer, Error code is set to allow user to identify error type, + and HAL_UART_ErrorCallback() user callback is executed. Transfer is kept ongoing on UART side. + If user wants to abort it, Abort services should be called by user. + (+) Error is considered as Blocking : Transfer could not be completed properly and is aborted. + This concerns Overrun Error In Interrupt mode reception and all errors in DMA mode. + Error code is set to allow user to identify error type, and HAL_UART_ErrorCallback() user callback is executed. + + -@- In the Half duplex communication, it is forbidden to run the transmit + and receive process in parallel, the UART state HAL_UART_STATE_BUSY_TX_RX can't be useful. + +@endverbatim + * @{ + */ + +/** + * @brief Sends an amount of data in blocking mode. + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), + * the sent data is handled as a set of u16. In this case, Size must indicate the number + * of u16 provided through pData. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData Pointer to data buffer (u8 or u16 data elements). + * @param Size Amount of data elements (u8 or u16) to be sent + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, const uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + const uint8_t *pdata8bits; + const uint16_t *pdata16bits; + uint32_t tickstart = 0U; + + /* Check that a Tx process is not already ongoing */ + if (huart->gState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_BUSY_TX; + + /* Init tickstart for timeout management */ + tickstart = HAL_GetTick(); + + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + /* In case of 9bits/No Parity transfer, pData needs to be handled as a uint16_t pointer */ + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + pdata8bits = NULL; + pdata16bits = (const uint16_t *) pData; + } + else + { + pdata8bits = pData; + pdata16bits = NULL; + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + while (huart->TxXferCount > 0U) + { + if (UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TXE, RESET, tickstart, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + if (pdata8bits == NULL) + { + huart->Instance->DR = (uint16_t)(*pdata16bits & 0x01FFU); + pdata16bits++; + } + else + { + huart->Instance->DR = (uint8_t)(*pdata8bits & 0xFFU); + pdata8bits++; + } + huart->TxXferCount--; + } + + if (UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_TC, RESET, tickstart, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + + /* At end of Tx process, restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in blocking mode. + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), + * the received data is handled as a set of u16. In this case, Size must indicate the number + * of u16 available through pData. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData Pointer to data buffer (u8 or u16 data elements). + * @param Size Amount of data elements (u8 or u16) to be received. + * @param Timeout Timeout duration + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout) +{ + uint8_t *pdata8bits; + uint16_t *pdata16bits; + uint32_t tickstart = 0U; + + /* Check that a Rx process is not already ongoing */ + if (huart->RxState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->RxState = HAL_UART_STATE_BUSY_RX; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* Init tickstart for timeout management */ + tickstart = HAL_GetTick(); + + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + /* In case of 9bits/No Parity transfer, pRxData needs to be handled as a uint16_t pointer */ + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + pdata8bits = NULL; + pdata16bits = (uint16_t *) pData; + } + else + { + pdata8bits = pData; + pdata16bits = NULL; + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Check the remain data to be received */ + while (huart->RxXferCount > 0U) + { + if (UART_WaitOnFlagUntilTimeout(huart, UART_FLAG_RXNE, RESET, tickstart, Timeout) != HAL_OK) + { + return HAL_TIMEOUT; + } + if (pdata8bits == NULL) + { + *pdata16bits = (uint16_t)(huart->Instance->DR & 0x01FF); + pdata16bits++; + } + else + { + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) || ((huart->Init.WordLength == UART_WORDLENGTH_8B) && (huart->Init.Parity == UART_PARITY_NONE))) + { + *pdata8bits = (uint8_t)(huart->Instance->DR & (uint8_t)0x00FF); + } + else + { + *pdata8bits = (uint8_t)(huart->Instance->DR & (uint8_t)0x007F); + } + pdata8bits++; + } + huart->RxXferCount--; + } + + /* At end of Rx process, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sends an amount of data in non blocking mode. + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), + * the sent data is handled as a set of u16. In this case, Size must indicate the number + * of u16 provided through pData. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData Pointer to data buffer (u8 or u16 data elements). + * @param Size Amount of data elements (u8 or u16) to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, const uint8_t *pData, uint16_t Size) +{ + /* Check that a Tx process is not already ongoing */ + if (huart->gState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pTxBuffPtr = pData; + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_BUSY_TX; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the UART Transmit data register empty Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_TXE); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in non blocking mode. + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), + * the received data is handled as a set of u16. In this case, Size must indicate the number + * of u16 available through pData. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData Pointer to data buffer (u8 or u16 data elements). + * @param Size Amount of data elements (u8 or u16) to be received. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + /* Check that a Rx process is not already ongoing */ + if (huart->RxState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + /* Set Reception type to Standard reception */ + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + return (UART_Start_Receive_IT(huart, pData, Size)); + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Sends an amount of data in DMA mode. + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), + * the sent data is handled as a set of u16. In this case, Size must indicate the number + * of u16 provided through pData. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData Pointer to data buffer (u8 or u16 data elements). + * @param Size Amount of data elements (u8 or u16) to be sent + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, const uint8_t *pData, uint16_t Size) +{ + const uint32_t *tmp; + + /* Check that a Tx process is not already ongoing */ + if (huart->gState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->pTxBuffPtr = pData; + huart->TxXferSize = Size; + huart->TxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->gState = HAL_UART_STATE_BUSY_TX; + + /* Set the UART DMA transfer complete callback */ + huart->hdmatx->XferCpltCallback = UART_DMATransmitCplt; + + /* Set the UART DMA Half transfer complete callback */ + huart->hdmatx->XferHalfCpltCallback = UART_DMATxHalfCplt; + + /* Set the DMA error callback */ + huart->hdmatx->XferErrorCallback = UART_DMAError; + + /* Set the DMA abort callback */ + huart->hdmatx->XferAbortCallback = NULL; + + /* Enable the UART transmit DMA stream */ + tmp = (const uint32_t *)&pData; + HAL_DMA_Start_IT(huart->hdmatx, *(const uint32_t *)tmp, (uint32_t)&huart->Instance->DR, Size); + + /* Clear the TC flag in the SR register by writing 0 to it */ + __HAL_UART_CLEAR_FLAG(huart, UART_FLAG_TC); + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + /* Enable the DMA transfer for transmit request by setting the DMAT bit + in the UART CR3 register */ + ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receives an amount of data in DMA mode. + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M1-M0 = 01), + * the received data is handled as a set of u16. In this case, Size must indicate the number + * of u16 available through pData. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param pData Pointer to data buffer (u8 or u16 data elements). + * @param Size Amount of data elements (u8 or u16) to be received. + * @note When the UART parity is enabled (PCE = 1) the received data contains the parity bit. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + /* Check that a Rx process is not already ongoing */ + if (huart->RxState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + /* Process Locked */ + __HAL_LOCK(huart); + + /* Set Reception type to Standard reception */ + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + return (UART_Start_Receive_DMA(huart, pData, Size)); + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Pauses the DMA Transfer. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart) +{ + uint32_t dmarequest = 0x00U; + + /* Process Locked */ + __HAL_LOCK(huart); + + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT); + if ((huart->gState == HAL_UART_STATE_BUSY_TX) && dmarequest) + { + /* Disable the UART DMA Tx request */ + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + } + + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR); + if ((huart->RxState == HAL_UART_STATE_BUSY_RX) && dmarequest) + { + /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Disable the UART DMA Rx request */ + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Resumes the DMA Transfer. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart) +{ + /* Process Locked */ + __HAL_LOCK(huart); + + if (huart->gState == HAL_UART_STATE_BUSY_TX) + { + /* Enable the UART DMA Tx request */ + ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_DMAT); + } + + if (huart->RxState == HAL_UART_STATE_BUSY_RX) + { + /* Clear the Overrun flag before resuming the Rx transfer*/ + __HAL_UART_CLEAR_OREFLAG(huart); + + /* Re-enable PE and ERR (Frame error, noise error, overrun error) interrupts */ + if (huart->Init.Parity != UART_PARITY_NONE) + { + ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_PEIE); + } + ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Enable the UART DMA Rx request */ + ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_DMAR); + } + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Stops the DMA Transfer. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart) +{ + uint32_t dmarequest = 0x00U; + /* The Lock is not implemented on this API to allow the user application + to call the HAL UART API under callbacks HAL_UART_TxCpltCallback() / HAL_UART_RxCpltCallback(): + when calling HAL_DMA_Abort() API the DMA TX/RX Transfer complete interrupt is generated + and the correspond call back is executed HAL_UART_TxCpltCallback() / HAL_UART_RxCpltCallback() + */ + + /* Stop UART DMA Tx request if ongoing */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT); + if ((huart->gState == HAL_UART_STATE_BUSY_TX) && dmarequest) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Abort the UART DMA Tx stream */ + if (huart->hdmatx != NULL) + { + HAL_DMA_Abort(huart->hdmatx); + } + UART_EndTxTransfer(huart); + } + + /* Stop UART DMA Rx request if ongoing */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR); + if ((huart->RxState == HAL_UART_STATE_BUSY_RX) && dmarequest) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Abort the UART DMA Rx stream */ + if (huart->hdmarx != NULL) + { + HAL_DMA_Abort(huart->hdmarx); + } + UART_EndRxTransfer(huart); + } + + return HAL_OK; +} + +/** + * @brief Receive an amount of data in blocking mode till either the expected number of data is received or an IDLE event occurs. + * @note HAL_OK is returned if reception is completed (expected number of data has been received) + * or if reception is stopped after IDLE event (less than the expected number of data has been received) + * In this case, RxLen output parameter indicates number of data available in reception buffer. + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M = 01), + * the received data is handled as a set of uint16_t. In this case, Size must indicate the number + * of uint16_t available through pData. + * @param huart UART handle. + * @param pData Pointer to data buffer (uint8_t or uint16_t data elements). + * @param Size Amount of data elements (uint8_t or uint16_t) to be received. + * @param RxLen Number of data elements finally received (could be lower than Size, in case reception ends on IDLE event) + * @param Timeout Timeout duration expressed in ms (covers the whole reception sequence). + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint16_t *RxLen, + uint32_t Timeout) +{ + uint8_t *pdata8bits; + uint16_t *pdata16bits; + uint32_t tickstart; + + /* Check that a Rx process is not already ongoing */ + if (huart->RxState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + __HAL_LOCK(huart); + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->RxState = HAL_UART_STATE_BUSY_RX; + huart->ReceptionType = HAL_UART_RECEPTION_TOIDLE; + + /* Init tickstart for timeout management */ + tickstart = HAL_GetTick(); + + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + /* In case of 9bits/No Parity transfer, pRxData needs to be handled as a uint16_t pointer */ + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + pdata8bits = NULL; + pdata16bits = (uint16_t *) pData; + } + else + { + pdata8bits = pData; + pdata16bits = NULL; + } + + __HAL_UNLOCK(huart); + + /* Initialize output number of received elements */ + *RxLen = 0U; + + /* as long as data have to be received */ + while (huart->RxXferCount > 0U) + { + /* Check if IDLE flag is set */ + if (__HAL_UART_GET_FLAG(huart, UART_FLAG_IDLE)) + { + /* Clear IDLE flag in ISR */ + __HAL_UART_CLEAR_IDLEFLAG(huart); + + /* If Set, but no data ever received, clear flag without exiting loop */ + /* If Set, and data has already been received, this means Idle Event is valid : End reception */ + if (*RxLen > 0U) + { + huart->RxState = HAL_UART_STATE_READY; + + return HAL_OK; + } + } + + /* Check if RXNE flag is set */ + if (__HAL_UART_GET_FLAG(huart, UART_FLAG_RXNE)) + { + if (pdata8bits == NULL) + { + *pdata16bits = (uint16_t)(huart->Instance->DR & (uint16_t)0x01FF); + pdata16bits++; + } + else + { + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) || ((huart->Init.WordLength == UART_WORDLENGTH_8B) && (huart->Init.Parity == UART_PARITY_NONE))) + { + *pdata8bits = (uint8_t)(huart->Instance->DR & (uint8_t)0x00FF); + } + else + { + *pdata8bits = (uint8_t)(huart->Instance->DR & (uint8_t)0x007F); + } + + pdata8bits++; + } + /* Increment number of received elements */ + *RxLen += 1U; + huart->RxXferCount--; + } + + /* Check for the Timeout */ + if (Timeout != HAL_MAX_DELAY) + { + if (((HAL_GetTick() - tickstart) > Timeout) || (Timeout == 0U)) + { + huart->RxState = HAL_UART_STATE_READY; + + return HAL_TIMEOUT; + } + } + } + + /* Set number of received elements in output parameter : RxLen */ + *RxLen = huart->RxXferSize - huart->RxXferCount; + /* At end of Rx process, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive an amount of data in interrupt mode till either the expected number of data is received or an IDLE event occurs. + * @note Reception is initiated by this function call. Further progress of reception is achieved thanks + * to UART interrupts raised by RXNE and IDLE events. Callback is called at end of reception indicating + * number of received data elements. + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M = 01), + * the received data is handled as a set of uint16_t. In this case, Size must indicate the number + * of uint16_t available through pData. + * @param huart UART handle. + * @param pData Pointer to data buffer (uint8_t or uint16_t data elements). + * @param Size Amount of data elements (uint8_t or uint16_t) to be received. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + HAL_StatusTypeDef status; + + /* Check that a Rx process is not already ongoing */ + if (huart->RxState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + __HAL_LOCK(huart); + + /* Set Reception type to reception till IDLE Event*/ + huart->ReceptionType = HAL_UART_RECEPTION_TOIDLE; + + status = UART_Start_Receive_IT(huart, pData, Size); + + /* Check Rx process has been successfully started */ + if (status == HAL_OK) + { + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + __HAL_UART_CLEAR_IDLEFLAG(huart); + ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_IDLEIE); + } + else + { + /* In case of errors already pending when reception is started, + Interrupts may have already been raised and lead to reception abortion. + (Overrun error for instance). + In such case Reception Type has been reset to HAL_UART_RECEPTION_STANDARD. */ + status = HAL_ERROR; + } + } + + return status; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Receive an amount of data in DMA mode till either the expected number of data is received or an IDLE event occurs. + * @note Reception is initiated by this function call. Further progress of reception is achieved thanks + * to DMA services, transferring automatically received data elements in user reception buffer and + * calling registered callbacks at half/end of reception. UART IDLE events are also used to consider + * reception phase as ended. In all cases, callback execution will indicate number of received data elements. + * @note When the UART parity is enabled (PCE = 1), the received data contain + * the parity bit (MSB position). + * @note When UART parity is not enabled (PCE = 0), and Word Length is configured to 9 bits (M = 01), + * the received data is handled as a set of uint16_t. In this case, Size must indicate the number + * of uint16_t available through pData. + * @param huart UART handle. + * @param pData Pointer to data buffer (uint8_t or uint16_t data elements). + * @param Size Amount of data elements (uint8_t or uint16_t) to be received. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UARTEx_ReceiveToIdle_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + HAL_StatusTypeDef status; + + /* Check that a Rx process is not already ongoing */ + if (huart->RxState == HAL_UART_STATE_READY) + { + if ((pData == NULL) || (Size == 0U)) + { + return HAL_ERROR; + } + + __HAL_LOCK(huart); + + /* Set Reception type to reception till IDLE Event*/ + huart->ReceptionType = HAL_UART_RECEPTION_TOIDLE; + + status = UART_Start_Receive_DMA(huart, pData, Size); + + /* Check Rx process has been successfully started */ + if (status == HAL_OK) + { + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + __HAL_UART_CLEAR_IDLEFLAG(huart); + ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_IDLEIE); + } + else + { + /* In case of errors already pending when reception is started, + Interrupts may have already been raised and lead to reception abortion. + (Overrun error for instance). + In such case Reception Type has been reset to HAL_UART_RECEPTION_STANDARD. */ + status = HAL_ERROR; + } + } + + return status; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Abort ongoing transfers (blocking mode). + * @param huart UART handle. + * @note This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. + * This procedure performs following operations : + * - Disable UART Interrupts (Tx and Rx) + * - Disable the DMA transfer in the peripheral register (if enabled) + * - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode) + * - Set handle State to READY + * @note This procedure is executed in blocking mode : when exiting function, Abort is considered as completed. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Abort(UART_HandleTypeDef *huart) +{ + /* Disable TXEIE, TCIE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE)); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* If Reception till IDLE event was ongoing, disable IDLEIE interrupt */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE)); + } + + /* Disable the UART DMA Tx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT)) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Abort the UART DMA Tx stream: use blocking DMA Abort API (no callback) */ + if (huart->hdmatx != NULL) + { + /* Set the UART DMA Abort callback to Null. + No call back execution at end of DMA abort procedure */ + huart->hdmatx->XferAbortCallback = NULL; + + if (HAL_DMA_Abort(huart->hdmatx) != HAL_OK) + { + if (HAL_DMA_GetError(huart->hdmatx) == HAL_DMA_ERROR_TIMEOUT) + { + /* Set error code to DMA */ + huart->ErrorCode = HAL_UART_ERROR_DMA; + + return HAL_TIMEOUT; + } + } + } + } + + /* Disable the UART DMA Rx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Abort the UART DMA Rx stream: use blocking DMA Abort API (no callback) */ + if (huart->hdmarx != NULL) + { + /* Set the UART DMA Abort callback to Null. + No call back execution at end of DMA abort procedure */ + huart->hdmarx->XferAbortCallback = NULL; + + if (HAL_DMA_Abort(huart->hdmarx) != HAL_OK) + { + if (HAL_DMA_GetError(huart->hdmarx) == HAL_DMA_ERROR_TIMEOUT) + { + /* Set error code to DMA */ + huart->ErrorCode = HAL_UART_ERROR_DMA; + + return HAL_TIMEOUT; + } + } + } + } + + /* Reset Tx and Rx transfer counters */ + huart->TxXferCount = 0x00U; + huart->RxXferCount = 0x00U; + + /* Reset ErrorCode */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + + /* Restore huart->RxState and huart->gState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + huart->gState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + return HAL_OK; +} + +/** + * @brief Abort ongoing Transmit transfer (blocking mode). + * @param huart UART handle. + * @note This procedure could be used for aborting any ongoing Tx transfer started in Interrupt or DMA mode. + * This procedure performs following operations : + * - Disable UART Interrupts (Tx) + * - Disable the DMA transfer in the peripheral register (if enabled) + * - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode) + * - Set handle State to READY + * @note This procedure is executed in blocking mode : when exiting function, Abort is considered as completed. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_AbortTransmit(UART_HandleTypeDef *huart) +{ + /* Disable TXEIE and TCIE interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE)); + + /* Disable the UART DMA Tx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT)) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Abort the UART DMA Tx stream : use blocking DMA Abort API (no callback) */ + if (huart->hdmatx != NULL) + { + /* Set the UART DMA Abort callback to Null. + No call back execution at end of DMA abort procedure */ + huart->hdmatx->XferAbortCallback = NULL; + + if (HAL_DMA_Abort(huart->hdmatx) != HAL_OK) + { + if (HAL_DMA_GetError(huart->hdmatx) == HAL_DMA_ERROR_TIMEOUT) + { + /* Set error code to DMA */ + huart->ErrorCode = HAL_UART_ERROR_DMA; + + return HAL_TIMEOUT; + } + } + } + } + + /* Reset Tx transfer counter */ + huart->TxXferCount = 0x00U; + + /* Restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; + + return HAL_OK; +} + +/** + * @brief Abort ongoing Receive transfer (blocking mode). + * @param huart UART handle. + * @note This procedure could be used for aborting any ongoing Rx transfer started in Interrupt or DMA mode. + * This procedure performs following operations : + * - Disable UART Interrupts (Rx) + * - Disable the DMA transfer in the peripheral register (if enabled) + * - Abort DMA transfer by calling HAL_DMA_Abort (in case of transfer in DMA mode) + * - Set handle State to READY + * @note This procedure is executed in blocking mode : when exiting function, Abort is considered as completed. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_AbortReceive(UART_HandleTypeDef *huart) +{ + /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE)); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* If Reception till IDLE event was ongoing, disable IDLEIE interrupt */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE)); + } + + /* Disable the UART DMA Rx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Abort the UART DMA Rx stream : use blocking DMA Abort API (no callback) */ + if (huart->hdmarx != NULL) + { + /* Set the UART DMA Abort callback to Null. + No call back execution at end of DMA abort procedure */ + huart->hdmarx->XferAbortCallback = NULL; + + if (HAL_DMA_Abort(huart->hdmarx) != HAL_OK) + { + if (HAL_DMA_GetError(huart->hdmarx) == HAL_DMA_ERROR_TIMEOUT) + { + /* Set error code to DMA */ + huart->ErrorCode = HAL_UART_ERROR_DMA; + + return HAL_TIMEOUT; + } + } + } + } + + /* Reset Rx transfer counter */ + huart->RxXferCount = 0x00U; + + /* Restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + return HAL_OK; +} + +/** + * @brief Abort ongoing transfers (Interrupt mode). + * @param huart UART handle. + * @note This procedure could be used for aborting any ongoing transfer started in Interrupt or DMA mode. + * This procedure performs following operations : + * - Disable UART Interrupts (Tx and Rx) + * - Disable the DMA transfer in the peripheral register (if enabled) + * - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode) + * - Set handle State to READY + * - At abort completion, call user abort complete callback + * @note This procedure is executed in Interrupt mode, meaning that abort procedure could be + * considered as completed only when user abort complete callback is executed (not when exiting function). + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_Abort_IT(UART_HandleTypeDef *huart) +{ + uint32_t AbortCplt = 0x01U; + + /* Disable TXEIE, TCIE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE | USART_CR1_TCIE)); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* If Reception till IDLE event was ongoing, disable IDLEIE interrupt */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE)); + } + + /* If DMA Tx and/or DMA Rx Handles are associated to UART Handle, DMA Abort complete callbacks should be initialised + before any call to DMA Abort functions */ + /* DMA Tx Handle is valid */ + if (huart->hdmatx != NULL) + { + /* Set DMA Abort Complete callback if UART DMA Tx request if enabled. + Otherwise, set it to NULL */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT)) + { + huart->hdmatx->XferAbortCallback = UART_DMATxAbortCallback; + } + else + { + huart->hdmatx->XferAbortCallback = NULL; + } + } + /* DMA Rx Handle is valid */ + if (huart->hdmarx != NULL) + { + /* Set DMA Abort Complete callback if UART DMA Rx request if enabled. + Otherwise, set it to NULL */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) + { + huart->hdmarx->XferAbortCallback = UART_DMARxAbortCallback; + } + else + { + huart->hdmarx->XferAbortCallback = NULL; + } + } + + /* Disable the UART DMA Tx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT)) + { + /* Disable DMA Tx at UART level */ + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Abort the UART DMA Tx stream : use non blocking DMA Abort API (callback) */ + if (huart->hdmatx != NULL) + { + /* UART Tx DMA Abort callback has already been initialised : + will lead to call HAL_UART_AbortCpltCallback() at end of DMA abort procedure */ + + /* Abort DMA TX */ + if (HAL_DMA_Abort_IT(huart->hdmatx) != HAL_OK) + { + huart->hdmatx->XferAbortCallback = NULL; + } + else + { + AbortCplt = 0x00U; + } + } + } + + /* Disable the UART DMA Rx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Abort the UART DMA Rx stream : use non blocking DMA Abort API (callback) */ + if (huart->hdmarx != NULL) + { + /* UART Rx DMA Abort callback has already been initialised : + will lead to call HAL_UART_AbortCpltCallback() at end of DMA abort procedure */ + + /* Abort DMA RX */ + if (HAL_DMA_Abort_IT(huart->hdmarx) != HAL_OK) + { + huart->hdmarx->XferAbortCallback = NULL; + AbortCplt = 0x01U; + } + else + { + AbortCplt = 0x00U; + } + } + } + + /* if no DMA abort complete callback execution is required => call user Abort Complete callback */ + if (AbortCplt == 0x01U) + { + /* Reset Tx and Rx transfer counters */ + huart->TxXferCount = 0x00U; + huart->RxXferCount = 0x00U; + + /* Reset ErrorCode */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + + /* Restore huart->gState and huart->RxState to Ready */ + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* As no DMA to be aborted, call directly user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort complete callback */ + huart->AbortCpltCallback(huart); +#else + /* Call legacy weak Abort complete callback */ + HAL_UART_AbortCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + + return HAL_OK; +} + +/** + * @brief Abort ongoing Transmit transfer (Interrupt mode). + * @param huart UART handle. + * @note This procedure could be used for aborting any ongoing Tx transfer started in Interrupt or DMA mode. + * This procedure performs following operations : + * - Disable UART Interrupts (Tx) + * - Disable the DMA transfer in the peripheral register (if enabled) + * - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode) + * - Set handle State to READY + * - At abort completion, call user abort complete callback + * @note This procedure is executed in Interrupt mode, meaning that abort procedure could be + * considered as completed only when user abort complete callback is executed (not when exiting function). + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_AbortTransmit_IT(UART_HandleTypeDef *huart) +{ + /* Disable TXEIE and TCIE interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE)); + + /* Disable the UART DMA Tx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT)) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Abort the UART DMA Tx stream : use blocking DMA Abort API (no callback) */ + if (huart->hdmatx != NULL) + { + /* Set the UART DMA Abort callback : + will lead to call HAL_UART_AbortCpltCallback() at end of DMA abort procedure */ + huart->hdmatx->XferAbortCallback = UART_DMATxOnlyAbortCallback; + + /* Abort DMA TX */ + if (HAL_DMA_Abort_IT(huart->hdmatx) != HAL_OK) + { + /* Call Directly huart->hdmatx->XferAbortCallback function in case of error */ + huart->hdmatx->XferAbortCallback(huart->hdmatx); + } + } + else + { + /* Reset Tx transfer counter */ + huart->TxXferCount = 0x00U; + + /* Restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; + + /* As no DMA to be aborted, call directly user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort Transmit Complete Callback */ + huart->AbortTransmitCpltCallback(huart); +#else + /* Call legacy weak Abort Transmit Complete Callback */ + HAL_UART_AbortTransmitCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + } + else + { + /* Reset Tx transfer counter */ + huart->TxXferCount = 0x00U; + + /* Restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; + + /* As no DMA to be aborted, call directly user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort Transmit Complete Callback */ + huart->AbortTransmitCpltCallback(huart); +#else + /* Call legacy weak Abort Transmit Complete Callback */ + HAL_UART_AbortTransmitCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + + return HAL_OK; +} + +/** + * @brief Abort ongoing Receive transfer (Interrupt mode). + * @param huart UART handle. + * @note This procedure could be used for aborting any ongoing Rx transfer started in Interrupt or DMA mode. + * This procedure performs following operations : + * - Disable UART Interrupts (Rx) + * - Disable the DMA transfer in the peripheral register (if enabled) + * - Abort DMA transfer by calling HAL_DMA_Abort_IT (in case of transfer in DMA mode) + * - Set handle State to READY + * - At abort completion, call user abort complete callback + * @note This procedure is executed in Interrupt mode, meaning that abort procedure could be + * considered as completed only when user abort complete callback is executed (not when exiting function). + * @retval HAL status + */ +HAL_StatusTypeDef HAL_UART_AbortReceive_IT(UART_HandleTypeDef *huart) +{ + /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE)); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* If Reception till IDLE event was ongoing, disable IDLEIE interrupt */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_IDLEIE)); + } + + /* Disable the UART DMA Rx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Abort the UART DMA Rx stream : use blocking DMA Abort API (no callback) */ + if (huart->hdmarx != NULL) + { + /* Set the UART DMA Abort callback : + will lead to call HAL_UART_AbortCpltCallback() at end of DMA abort procedure */ + huart->hdmarx->XferAbortCallback = UART_DMARxOnlyAbortCallback; + + /* Abort DMA RX */ + if (HAL_DMA_Abort_IT(huart->hdmarx) != HAL_OK) + { + /* Call Directly huart->hdmarx->XferAbortCallback function in case of error */ + huart->hdmarx->XferAbortCallback(huart->hdmarx); + } + } + else + { + /* Reset Rx transfer counter */ + huart->RxXferCount = 0x00U; + + /* Restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* As no DMA to be aborted, call directly user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort Receive Complete Callback */ + huart->AbortReceiveCpltCallback(huart); +#else + /* Call legacy weak Abort Receive Complete Callback */ + HAL_UART_AbortReceiveCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + } + else + { + /* Reset Rx transfer counter */ + huart->RxXferCount = 0x00U; + + /* Restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* As no DMA to be aborted, call directly user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort Receive Complete Callback */ + huart->AbortReceiveCpltCallback(huart); +#else + /* Call legacy weak Abort Receive Complete Callback */ + HAL_UART_AbortReceiveCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + + return HAL_OK; +} + +/** + * @brief This function handles UART interrupt request. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +void HAL_UART_IRQHandler(UART_HandleTypeDef *huart) +{ + uint32_t isrflags = READ_REG(huart->Instance->SR); + uint32_t cr1its = READ_REG(huart->Instance->CR1); + uint32_t cr3its = READ_REG(huart->Instance->CR3); + uint32_t errorflags = 0x00U; + uint32_t dmarequest = 0x00U; + + /* If no error occurs */ + errorflags = (isrflags & (uint32_t)(USART_SR_PE | USART_SR_FE | USART_SR_ORE | USART_SR_NE)); + if (errorflags == RESET) + { + /* UART in mode Receiver -------------------------------------------------*/ + if (((isrflags & USART_SR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET)) + { + UART_Receive_IT(huart); + return; + } + } + + /* If some errors occur */ + if ((errorflags != RESET) && (((cr3its & USART_CR3_EIE) != RESET) + || ((cr1its & (USART_CR1_RXNEIE | USART_CR1_PEIE)) != RESET))) + { + /* UART parity error interrupt occurred ----------------------------------*/ + if (((isrflags & USART_SR_PE) != RESET) && ((cr1its & USART_CR1_PEIE) != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_PE; + } + + /* UART noise error interrupt occurred -----------------------------------*/ + if (((isrflags & USART_SR_NE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_NE; + } + + /* UART frame error interrupt occurred -----------------------------------*/ + if (((isrflags & USART_SR_FE) != RESET) && ((cr3its & USART_CR3_EIE) != RESET)) + { + huart->ErrorCode |= HAL_UART_ERROR_FE; + } + + /* UART Over-Run interrupt occurred --------------------------------------*/ + if (((isrflags & USART_SR_ORE) != RESET) && (((cr1its & USART_CR1_RXNEIE) != RESET) + || ((cr3its & USART_CR3_EIE) != RESET))) + { + huart->ErrorCode |= HAL_UART_ERROR_ORE; + } + + /* Call UART Error Call back function if need be --------------------------*/ + if (huart->ErrorCode != HAL_UART_ERROR_NONE) + { + /* UART in mode Receiver -----------------------------------------------*/ + if (((isrflags & USART_SR_RXNE) != RESET) && ((cr1its & USART_CR1_RXNEIE) != RESET)) + { + UART_Receive_IT(huart); + } + + /* If Overrun error occurs, or if any error occurs in DMA mode reception, + consider error as blocking */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR); + if (((huart->ErrorCode & HAL_UART_ERROR_ORE) != RESET) || dmarequest) + { + /* Blocking error : transfer is aborted + Set the UART state ready to be able to start again the process, + Disable Rx Interrupts, and disable Rx DMA request, if ongoing */ + UART_EndRxTransfer(huart); + + /* Disable the UART DMA Rx request if enabled */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* Abort the UART DMA Rx stream */ + if (huart->hdmarx != NULL) + { + /* Set the UART DMA Abort callback : + will lead to call HAL_UART_ErrorCallback() at end of DMA abort procedure */ + huart->hdmarx->XferAbortCallback = UART_DMAAbortOnError; + if (HAL_DMA_Abort_IT(huart->hdmarx) != HAL_OK) + { + /* Call Directly XferAbortCallback function in case of error */ + huart->hdmarx->XferAbortCallback(huart->hdmarx); + } + } + else + { + /* Call user error callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered error callback*/ + huart->ErrorCallback(huart); +#else + /*Call legacy weak error callback*/ + HAL_UART_ErrorCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + } + else + { + /* Call user error callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered error callback*/ + huart->ErrorCallback(huart); +#else + /*Call legacy weak error callback*/ + HAL_UART_ErrorCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + } + else + { + /* Non Blocking error : transfer could go on. + Error is notified to user through user error callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered error callback*/ + huart->ErrorCallback(huart); +#else + /*Call legacy weak error callback*/ + HAL_UART_ErrorCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + + huart->ErrorCode = HAL_UART_ERROR_NONE; + } + } + return; + } /* End if some error occurs */ + + /* Check current reception Mode : + If Reception till IDLE event has been selected : */ + if ((huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + && ((isrflags & USART_SR_IDLE) != 0U) + && ((cr1its & USART_SR_IDLE) != 0U)) + { + __HAL_UART_CLEAR_IDLEFLAG(huart); + + /* Check if DMA mode is enabled in UART */ + if (HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR)) + { + /* DMA mode enabled */ + /* Check received length : If all expected data are received, do nothing, + (DMA cplt callback will be called). + Otherwise, if at least one data has already been received, IDLE event is to be notified to user */ + uint16_t nb_remaining_rx_data = (uint16_t) __HAL_DMA_GET_COUNTER(huart->hdmarx); + if ((nb_remaining_rx_data > 0U) + && (nb_remaining_rx_data < huart->RxXferSize)) + { + /* Reception is not complete */ + huart->RxXferCount = nb_remaining_rx_data; + + /* In Normal mode, end DMA xfer and HAL UART Rx process*/ + if (huart->hdmarx->Init.Mode != DMA_CIRCULAR) + { + /* Disable PE and ERR (Frame error, noise error, overrun error) interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Disable the DMA transfer for the receiver request by resetting the DMAR bit + in the UART CR3 register */ + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* At end of Rx process, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE); + + /* Last bytes received, so no need as the abort is immediate */ + (void)HAL_DMA_Abort(huart->hdmarx); + } +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Rx Event callback*/ + huart->RxEventCallback(huart, (huart->RxXferSize - huart->RxXferCount)); +#else + /*Call legacy weak Rx Event callback*/ + HAL_UARTEx_RxEventCallback(huart, (huart->RxXferSize - huart->RxXferCount)); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + return; + } + else + { + /* DMA mode not enabled */ + /* Check received length : If all expected data are received, do nothing. + Otherwise, if at least one data has already been received, IDLE event is to be notified to user */ + uint16_t nb_rx_data = huart->RxXferSize - huart->RxXferCount; + if ((huart->RxXferCount > 0U) + && (nb_rx_data > 0U)) + { + /* Disable the UART Parity Error Interrupt and RXNE interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE)); + + /* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Rx process is completed, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE); +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Rx complete callback*/ + huart->RxEventCallback(huart, nb_rx_data); +#else + /*Call legacy weak Rx Event callback*/ + HAL_UARTEx_RxEventCallback(huart, nb_rx_data); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + return; + } + } + + /* UART in mode Transmitter ------------------------------------------------*/ + if (((isrflags & USART_SR_TXE) != RESET) && ((cr1its & USART_CR1_TXEIE) != RESET)) + { + UART_Transmit_IT(huart); + return; + } + + /* UART in mode Transmitter end --------------------------------------------*/ + if (((isrflags & USART_SR_TC) != RESET) && ((cr1its & USART_CR1_TCIE) != RESET)) + { + UART_EndTransmit_IT(huart); + return; + } +} + +/** + * @brief Tx Transfer completed callbacks. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_TxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Tx Half Transfer completed callbacks. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_TxHalfCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Rx Transfer completed callbacks. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_RxCpltCallback could be implemented in the user file + */ +} + +/** + * @brief Rx Half Transfer completed callbacks. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_RxHalfCpltCallback could be implemented in the user file + */ +} + +/** + * @brief UART error callbacks. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +__weak void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + /* NOTE: This function should not be modified, when the callback is needed, + the HAL_UART_ErrorCallback could be implemented in the user file + */ +} + +/** + * @brief UART Abort Complete callback. + * @param huart UART handle. + * @retval None + */ +__weak void HAL_UART_AbortCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UART_AbortCpltCallback can be implemented in the user file. + */ +} + +/** + * @brief UART Abort Complete callback. + * @param huart UART handle. + * @retval None + */ +__weak void HAL_UART_AbortTransmitCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UART_AbortTransmitCpltCallback can be implemented in the user file. + */ +} + +/** + * @brief UART Abort Receive Complete callback. + * @param huart UART handle. + * @retval None + */ +__weak void HAL_UART_AbortReceiveCpltCallback(UART_HandleTypeDef *huart) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UART_AbortReceiveCpltCallback can be implemented in the user file. + */ +} + +/** + * @brief Reception Event Callback (Rx event notification called after use of advanced reception service). + * @param huart UART handle + * @param Size Number of data available in application reception buffer (indicates a position in + * reception buffer until which, data are available) + * @retval None + */ +__weak void HAL_UARTEx_RxEventCallback(UART_HandleTypeDef *huart, uint16_t Size) +{ + /* Prevent unused argument(s) compilation warning */ + UNUSED(huart); + UNUSED(Size); + + /* NOTE : This function should not be modified, when the callback is needed, + the HAL_UARTEx_RxEventCallback can be implemented in the user file. + */ +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group3 Peripheral Control functions + * @brief UART control functions + * +@verbatim + ============================================================================== + ##### Peripheral Control functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to control the UART: + (+) HAL_LIN_SendBreak() API can be helpful to transmit the break character. + (+) HAL_MultiProcessor_EnterMuteMode() API can be helpful to enter the UART in mute mode. + (+) HAL_MultiProcessor_ExitMuteMode() API can be helpful to exit the UART mute mode by software. + (+) HAL_HalfDuplex_EnableTransmitter() API to enable the UART transmitter and disables the UART receiver in Half Duplex mode + (+) HAL_HalfDuplex_EnableReceiver() API to enable the UART receiver and disables the UART transmitter in Half Duplex mode + +@endverbatim + * @{ + */ + +/** + * @brief Transmits break characters. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /* Send break characters */ + ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_SBK); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enters the UART in mute mode. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /* Enable the USART mute mode by setting the RWU bit in the CR1 register */ + ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_RWU); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Exits the UART mute mode: wake up software. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_MultiProcessor_ExitMuteMode(UART_HandleTypeDef *huart) +{ + /* Check the parameters */ + assert_param(IS_UART_INSTANCE(huart->Instance)); + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /* Disable the USART mute mode by clearing the RWU bit in the CR1 register */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_RWU); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enables the UART transmitter and disables the UART receiver. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart) +{ + uint32_t tmpreg = 0x00U; + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /*-------------------------- USART CR1 Configuration -----------------------*/ + tmpreg = huart->Instance->CR1; + + /* Clear TE and RE bits */ + tmpreg &= (uint32_t)~((uint32_t)(USART_CR1_TE | USART_CR1_RE)); + + /* Enable the USART's transmit interface by setting the TE bit in the USART CR1 register */ + tmpreg |= (uint32_t)USART_CR1_TE; + + /* Write to USART CR1 */ + WRITE_REG(huart->Instance->CR1, (uint32_t)tmpreg); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @brief Enables the UART receiver and disables the UART transmitter. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart) +{ + uint32_t tmpreg = 0x00U; + + /* Process Locked */ + __HAL_LOCK(huart); + + huart->gState = HAL_UART_STATE_BUSY; + + /*-------------------------- USART CR1 Configuration -----------------------*/ + tmpreg = huart->Instance->CR1; + + /* Clear TE and RE bits */ + tmpreg &= (uint32_t)~((uint32_t)(USART_CR1_TE | USART_CR1_RE)); + + /* Enable the USART's receive interface by setting the RE bit in the USART CR1 register */ + tmpreg |= (uint32_t)USART_CR1_RE; + + /* Write to USART CR1 */ + WRITE_REG(huart->Instance->CR1, (uint32_t)tmpreg); + + huart->gState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup UART_Exported_Functions_Group4 Peripheral State and Errors functions + * @brief UART State and Errors functions + * +@verbatim + ============================================================================== + ##### Peripheral State and Errors functions ##### + ============================================================================== + [..] + This subsection provides a set of functions allowing to return the State of + UART communication process, return Peripheral Errors occurred during communication + process + (+) HAL_UART_GetState() API can be helpful to check in run-time the state of the UART peripheral. + (+) HAL_UART_GetError() check in run-time errors that could be occurred during communication. + +@endverbatim + * @{ + */ + +/** + * @brief Returns the UART state. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL state + */ +HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart) +{ + uint32_t temp1 = 0x00U, temp2 = 0x00U; + temp1 = huart->gState; + temp2 = huart->RxState; + + return (HAL_UART_StateTypeDef)(temp1 | temp2); +} + +/** + * @brief Return the UART error code + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART. + * @retval UART Error Code + */ +uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart) +{ + return huart->ErrorCode; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup UART_Private_Functions UART Private Functions + * @{ + */ + +/** + * @brief Initialize the callbacks to their default values. + * @param huart UART handle. + * @retval none + */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) +void UART_InitCallbacksToDefault(UART_HandleTypeDef *huart) +{ + /* Init the UART Callback settings */ + huart->TxHalfCpltCallback = HAL_UART_TxHalfCpltCallback; /* Legacy weak TxHalfCpltCallback */ + huart->TxCpltCallback = HAL_UART_TxCpltCallback; /* Legacy weak TxCpltCallback */ + huart->RxHalfCpltCallback = HAL_UART_RxHalfCpltCallback; /* Legacy weak RxHalfCpltCallback */ + huart->RxCpltCallback = HAL_UART_RxCpltCallback; /* Legacy weak RxCpltCallback */ + huart->ErrorCallback = HAL_UART_ErrorCallback; /* Legacy weak ErrorCallback */ + huart->AbortCpltCallback = HAL_UART_AbortCpltCallback; /* Legacy weak AbortCpltCallback */ + huart->AbortTransmitCpltCallback = HAL_UART_AbortTransmitCpltCallback; /* Legacy weak AbortTransmitCpltCallback */ + huart->AbortReceiveCpltCallback = HAL_UART_AbortReceiveCpltCallback; /* Legacy weak AbortReceiveCpltCallback */ + huart->RxEventCallback = HAL_UARTEx_RxEventCallback; /* Legacy weak RxEventCallback */ + +} +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + +/** + * @brief DMA UART transmit process complete callback. + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMATransmitCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + /* DMA Normal mode*/ + if ((hdma->Instance->CR & DMA_SxCR_CIRC) == 0U) + { + huart->TxXferCount = 0x00U; + + /* Disable the DMA transfer for transmit request by setting the DMAT bit + in the UART CR3 register */ + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAT); + + /* Enable the UART Transmit Complete Interrupt */ + ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_TCIE); + + } + /* DMA Circular mode */ + else + { +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Tx complete callback*/ + huart->TxCpltCallback(huart); +#else + /*Call legacy weak Tx complete callback*/ + HAL_UART_TxCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } +} + +/** + * @brief DMA UART transmit process half complete callback + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMATxHalfCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Tx complete callback*/ + huart->TxHalfCpltCallback(huart); +#else + /*Call legacy weak Tx complete callback*/ + HAL_UART_TxHalfCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +} + +/** + * @brief DMA UART receive process complete callback. + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMAReceiveCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + /* DMA Normal mode*/ + if ((hdma->Instance->CR & DMA_SxCR_CIRC) == 0U) + { + huart->RxXferCount = 0U; + + /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_PEIE); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Disable the DMA transfer for the receiver request by setting the DMAR bit + in the UART CR3 register */ + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + /* At end of Rx process, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + + /* If Reception till IDLE event has been selected, Disable IDLE Interrupt */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE); + } + } + + /* Check current reception Mode : + If Reception till IDLE event has been selected : use Rx Event callback */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Rx Event callback*/ + huart->RxEventCallback(huart, huart->RxXferSize); +#else + /*Call legacy weak Rx Event callback*/ + HAL_UARTEx_RxEventCallback(huart, huart->RxXferSize); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + else + { + /* In other cases : use Rx Complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Rx complete callback*/ + huart->RxCpltCallback(huart); +#else + /*Call legacy weak Rx complete callback*/ + HAL_UART_RxCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } +} + +/** + * @brief DMA UART receive process half complete callback + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMARxHalfCplt(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + + /* Check current reception Mode : + If Reception till IDLE event has been selected : use Rx Event callback */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Rx Event callback*/ + huart->RxEventCallback(huart, huart->RxXferSize / 2U); +#else + /*Call legacy weak Rx Event callback*/ + HAL_UARTEx_RxEventCallback(huart, huart->RxXferSize / 2U); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + else + { + /* In other cases : use Rx Half Complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Rx Half complete callback*/ + huart->RxHalfCpltCallback(huart); +#else + /*Call legacy weak Rx Half complete callback*/ + HAL_UART_RxHalfCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } +} + +/** + * @brief DMA UART communication error callback. + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMAError(DMA_HandleTypeDef *hdma) +{ + uint32_t dmarequest = 0x00U; + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + + /* Stop UART DMA Tx request if ongoing */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAT); + if ((huart->gState == HAL_UART_STATE_BUSY_TX) && dmarequest) + { + huart->TxXferCount = 0x00U; + UART_EndTxTransfer(huart); + } + + /* Stop UART DMA Rx request if ongoing */ + dmarequest = HAL_IS_BIT_SET(huart->Instance->CR3, USART_CR3_DMAR); + if ((huart->RxState == HAL_UART_STATE_BUSY_RX) && dmarequest) + { + huart->RxXferCount = 0x00U; + UART_EndRxTransfer(huart); + } + + huart->ErrorCode |= HAL_UART_ERROR_DMA; +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered error callback*/ + huart->ErrorCallback(huart); +#else + /*Call legacy weak error callback*/ + HAL_UART_ErrorCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +} + +/** + * @brief This function handles UART Communication Timeout. It waits + * until a flag is no longer in the specified status. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @param Flag specifies the UART flag to check. + * @param Status The actual Flag status (SET or RESET). + * @param Tickstart Tick start value + * @param Timeout Timeout duration + * @retval HAL status + */ +static HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, + uint32_t Tickstart, uint32_t Timeout) +{ + /* Wait until flag is set */ + while ((__HAL_UART_GET_FLAG(huart, Flag) ? SET : RESET) == Status) + { + /* Check for the Timeout */ + if (Timeout != HAL_MAX_DELAY) + { + if ((Timeout == 0U) || ((HAL_GetTick() - Tickstart) > Timeout)) + { + /* Disable TXE, RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts for the interrupt process */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE | USART_CR1_TXEIE)); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + return HAL_TIMEOUT; + } + } + } + return HAL_OK; +} + +/** + * @brief Start Receive operation in interrupt mode. + * @note This function could be called by all HAL UART API providing reception in Interrupt mode. + * @note When calling this function, parameters validity is considered as already checked, + * i.e. Rx State, buffer address, ... + * UART Handle is assumed as Locked. + * @param huart UART handle. + * @param pData Pointer to data buffer (u8 or u16 data elements). + * @param Size Amount of data elements (u8 or u16) to be received. + * @retval HAL status + */ +HAL_StatusTypeDef UART_Start_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + huart->pRxBuffPtr = pData; + huart->RxXferSize = Size; + huart->RxXferCount = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->RxState = HAL_UART_STATE_BUSY_RX; + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + if (huart->Init.Parity != UART_PARITY_NONE) + { + /* Enable the UART Parity Error Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_PE); + } + + /* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_ENABLE_IT(huart, UART_IT_ERR); + + /* Enable the UART Data Register not empty Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_RXNE); + + return HAL_OK; +} + +/** + * @brief Start Receive operation in DMA mode. + * @note This function could be called by all HAL UART API providing reception in DMA mode. + * @note When calling this function, parameters validity is considered as already checked, + * i.e. Rx State, buffer address, ... + * UART Handle is assumed as Locked. + * @param huart UART handle. + * @param pData Pointer to data buffer (u8 or u16 data elements). + * @param Size Amount of data elements (u8 or u16) to be received. + * @retval HAL status + */ +HAL_StatusTypeDef UART_Start_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size) +{ + uint32_t *tmp; + + huart->pRxBuffPtr = pData; + huart->RxXferSize = Size; + + huart->ErrorCode = HAL_UART_ERROR_NONE; + huart->RxState = HAL_UART_STATE_BUSY_RX; + + /* Set the UART DMA transfer complete callback */ + huart->hdmarx->XferCpltCallback = UART_DMAReceiveCplt; + + /* Set the UART DMA Half transfer complete callback */ + huart->hdmarx->XferHalfCpltCallback = UART_DMARxHalfCplt; + + /* Set the DMA error callback */ + huart->hdmarx->XferErrorCallback = UART_DMAError; + + /* Set the DMA abort callback */ + huart->hdmarx->XferAbortCallback = NULL; + + /* Enable the DMA stream */ + tmp = (uint32_t *)&pData; + HAL_DMA_Start_IT(huart->hdmarx, (uint32_t)&huart->Instance->DR, *(uint32_t *)tmp, Size); + + /* Clear the Overrun flag just before enabling the DMA Rx request: can be mandatory for the second transfer */ + __HAL_UART_CLEAR_OREFLAG(huart); + + /* Process Unlocked */ + __HAL_UNLOCK(huart); + + if (huart->Init.Parity != UART_PARITY_NONE) + { + /* Enable the UART Parity Error Interrupt */ + ATOMIC_SET_BIT(huart->Instance->CR1, USART_CR1_PEIE); + } + + /* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* Enable the DMA transfer for the receiver request by setting the DMAR bit + in the UART CR3 register */ + ATOMIC_SET_BIT(huart->Instance->CR3, USART_CR3_DMAR); + + return HAL_OK; +} + +/** + * @brief End ongoing Tx transfer on UART peripheral (following error detection or Transmit completion). + * @param huart UART handle. + * @retval None + */ +static void UART_EndTxTransfer(UART_HandleTypeDef *huart) +{ + /* Disable TXEIE and TCIE interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_TXEIE | USART_CR1_TCIE)); + + /* At end of Tx process, restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; +} + +/** + * @brief End ongoing Rx transfer on UART peripheral (following error detection or Reception completion). + * @param huart UART handle. + * @retval None + */ +static void UART_EndRxTransfer(UART_HandleTypeDef *huart) +{ + /* Disable RXNE, PE and ERR (Frame error, noise error, overrun error) interrupts */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, (USART_CR1_RXNEIE | USART_CR1_PEIE)); + ATOMIC_CLEAR_BIT(huart->Instance->CR3, USART_CR3_EIE); + + /* In case of reception waiting for IDLE event, disable also the IDLE IE interrupt source */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE); + } + + /* At end of Rx process, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; +} + +/** + * @brief DMA UART communication abort callback, when initiated by HAL services on Error + * (To be called at end of DMA Abort procedure following error occurrence). + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMAAbortOnError(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + huart->RxXferCount = 0x00U; + huart->TxXferCount = 0x00U; + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered error callback*/ + huart->ErrorCallback(huart); +#else + /*Call legacy weak error callback*/ + HAL_UART_ErrorCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +} + +/** + * @brief DMA UART Tx communication abort callback, when initiated by user + * (To be called at end of DMA Tx Abort procedure following user abort request). + * @note When this callback is executed, User Abort complete call back is called only if no + * Abort still ongoing for Rx DMA Handle. + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMATxAbortCallback(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + + huart->hdmatx->XferAbortCallback = NULL; + + /* Check if an Abort process is still ongoing */ + if (huart->hdmarx != NULL) + { + if (huart->hdmarx->XferAbortCallback != NULL) + { + return; + } + } + + /* No Abort process still ongoing : All DMA channels are aborted, call user Abort Complete callback */ + huart->TxXferCount = 0x00U; + huart->RxXferCount = 0x00U; + + /* Reset ErrorCode */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + + /* Restore huart->gState and huart->RxState to Ready */ + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* Call user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort complete callback */ + huart->AbortCpltCallback(huart); +#else + /* Call legacy weak Abort complete callback */ + HAL_UART_AbortCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +} + +/** + * @brief DMA UART Rx communication abort callback, when initiated by user + * (To be called at end of DMA Rx Abort procedure following user abort request). + * @note When this callback is executed, User Abort complete call back is called only if no + * Abort still ongoing for Tx DMA Handle. + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMARxAbortCallback(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + + huart->hdmarx->XferAbortCallback = NULL; + + /* Check if an Abort process is still ongoing */ + if (huart->hdmatx != NULL) + { + if (huart->hdmatx->XferAbortCallback != NULL) + { + return; + } + } + + /* No Abort process still ongoing : All DMA channels are aborted, call user Abort Complete callback */ + huart->TxXferCount = 0x00U; + huart->RxXferCount = 0x00U; + + /* Reset ErrorCode */ + huart->ErrorCode = HAL_UART_ERROR_NONE; + + /* Restore huart->gState and huart->RxState to Ready */ + huart->gState = HAL_UART_STATE_READY; + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* Call user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort complete callback */ + huart->AbortCpltCallback(huart); +#else + /* Call legacy weak Abort complete callback */ + HAL_UART_AbortCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +} + +/** + * @brief DMA UART Tx communication abort callback, when initiated by user by a call to + * HAL_UART_AbortTransmit_IT API (Abort only Tx transfer) + * (This callback is executed at end of DMA Tx Abort procedure following user abort request, + * and leads to user Tx Abort Complete callback execution). + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMATxOnlyAbortCallback(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + + huart->TxXferCount = 0x00U; + + /* Restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; + + /* Call user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort Transmit Complete Callback */ + huart->AbortTransmitCpltCallback(huart); +#else + /* Call legacy weak Abort Transmit Complete Callback */ + HAL_UART_AbortTransmitCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +} + +/** + * @brief DMA UART Rx communication abort callback, when initiated by user by a call to + * HAL_UART_AbortReceive_IT API (Abort only Rx transfer) + * (This callback is executed at end of DMA Rx Abort procedure following user abort request, + * and leads to user Rx Abort Complete callback execution). + * @param hdma Pointer to a DMA_HandleTypeDef structure that contains + * the configuration information for the specified DMA module. + * @retval None + */ +static void UART_DMARxOnlyAbortCallback(DMA_HandleTypeDef *hdma) +{ + UART_HandleTypeDef *huart = (UART_HandleTypeDef *)((DMA_HandleTypeDef *)hdma)->Parent; + + huart->RxXferCount = 0x00U; + + /* Restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* Call user Abort complete callback */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /* Call registered Abort Receive Complete Callback */ + huart->AbortReceiveCpltCallback(huart); +#else + /* Call legacy weak Abort Receive Complete Callback */ + HAL_UART_AbortReceiveCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ +} + +/** + * @brief Sends an amount of data in non blocking mode. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart) +{ + const uint16_t *tmp; + + /* Check that a Tx process is ongoing */ + if (huart->gState == HAL_UART_STATE_BUSY_TX) + { + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + tmp = (const uint16_t *) huart->pTxBuffPtr; + huart->Instance->DR = (uint16_t)(*tmp & (uint16_t)0x01FF); + huart->pTxBuffPtr += 2U; + } + else + { + huart->Instance->DR = (uint8_t)(*huart->pTxBuffPtr++ & (uint8_t)0x00FF); + } + + if (--huart->TxXferCount == 0U) + { + /* Disable the UART Transmit Data Register Empty Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TXE); + + /* Enable the UART Transmit Complete Interrupt */ + __HAL_UART_ENABLE_IT(huart, UART_IT_TC); + } + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Wraps up transmission in non blocking mode. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart) +{ + /* Disable the UART Transmit Complete Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_TC); + + /* Tx process is ended, restore huart->gState to Ready */ + huart->gState = HAL_UART_STATE_READY; + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Tx complete callback*/ + huart->TxCpltCallback(huart); +#else + /*Call legacy weak Tx complete callback*/ + HAL_UART_TxCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + + return HAL_OK; +} + +/** + * @brief Receives an amount of data in non blocking mode + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval HAL status + */ +static HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart) +{ + uint8_t *pdata8bits; + uint16_t *pdata16bits; + + /* Check that a Rx process is ongoing */ + if (huart->RxState == HAL_UART_STATE_BUSY_RX) + { + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) && (huart->Init.Parity == UART_PARITY_NONE)) + { + pdata8bits = NULL; + pdata16bits = (uint16_t *) huart->pRxBuffPtr; + *pdata16bits = (uint16_t)(huart->Instance->DR & (uint16_t)0x01FF); + huart->pRxBuffPtr += 2U; + } + else + { + pdata8bits = (uint8_t *) huart->pRxBuffPtr; + pdata16bits = NULL; + + if ((huart->Init.WordLength == UART_WORDLENGTH_9B) || ((huart->Init.WordLength == UART_WORDLENGTH_8B) && (huart->Init.Parity == UART_PARITY_NONE))) + { + *pdata8bits = (uint8_t)(huart->Instance->DR & (uint8_t)0x00FF); + } + else + { + *pdata8bits = (uint8_t)(huart->Instance->DR & (uint8_t)0x007F); + } + huart->pRxBuffPtr += 1U; + } + + if (--huart->RxXferCount == 0U) + { + /* Disable the UART Data Register not empty Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_RXNE); + + /* Disable the UART Parity Error Interrupt */ + __HAL_UART_DISABLE_IT(huart, UART_IT_PE); + + /* Disable the UART Error Interrupt: (Frame error, noise error, overrun error) */ + __HAL_UART_DISABLE_IT(huart, UART_IT_ERR); + + /* Rx process is completed, restore huart->RxState to Ready */ + huart->RxState = HAL_UART_STATE_READY; + + /* Check current reception Mode : + If Reception till IDLE event has been selected : */ + if (huart->ReceptionType == HAL_UART_RECEPTION_TOIDLE) + { + /* Set reception type to Standard */ + huart->ReceptionType = HAL_UART_RECEPTION_STANDARD; + + /* Disable IDLE interrupt */ + ATOMIC_CLEAR_BIT(huart->Instance->CR1, USART_CR1_IDLEIE); + + /* Check if IDLE flag is set */ + if (__HAL_UART_GET_FLAG(huart, UART_FLAG_IDLE)) + { + /* Clear IDLE flag in ISR */ + __HAL_UART_CLEAR_IDLEFLAG(huart); + } + +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Rx Event callback*/ + huart->RxEventCallback(huart, huart->RxXferSize); +#else + /*Call legacy weak Rx Event callback*/ + HAL_UARTEx_RxEventCallback(huart, huart->RxXferSize); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + else + { + /* Standard reception API called */ +#if (USE_HAL_UART_REGISTER_CALLBACKS == 1) + /*Call registered Rx complete callback*/ + huart->RxCpltCallback(huart); +#else + /*Call legacy weak Rx complete callback*/ + HAL_UART_RxCpltCallback(huart); +#endif /* USE_HAL_UART_REGISTER_CALLBACKS */ + } + + return HAL_OK; + } + return HAL_OK; + } + else + { + return HAL_BUSY; + } +} + +/** + * @brief Configures the UART peripheral. + * @param huart Pointer to a UART_HandleTypeDef structure that contains + * the configuration information for the specified UART module. + * @retval None + */ +static void UART_SetConfig(UART_HandleTypeDef *huart) +{ + uint32_t tmpreg; + uint32_t pclk; + + /* Check the parameters */ + assert_param(IS_UART_BAUDRATE(huart->Init.BaudRate)); + assert_param(IS_UART_STOPBITS(huart->Init.StopBits)); + assert_param(IS_UART_PARITY(huart->Init.Parity)); + assert_param(IS_UART_MODE(huart->Init.Mode)); + + /*-------------------------- USART CR2 Configuration -----------------------*/ + /* Configure the UART Stop Bits: Set STOP[13:12] bits + according to huart->Init.StopBits value */ + MODIFY_REG(huart->Instance->CR2, USART_CR2_STOP, huart->Init.StopBits); + + /*-------------------------- USART CR1 Configuration -----------------------*/ + /* Configure the UART Word Length, Parity and mode: + Set the M bits according to huart->Init.WordLength value + Set PCE and PS bits according to huart->Init.Parity value + Set TE and RE bits according to huart->Init.Mode value + Set OVER8 bit according to huart->Init.OverSampling value */ + + tmpreg = (uint32_t)huart->Init.WordLength | huart->Init.Parity | huart->Init.Mode | huart->Init.OverSampling; + MODIFY_REG(huart->Instance->CR1, + (uint32_t)(USART_CR1_M | USART_CR1_PCE | USART_CR1_PS | USART_CR1_TE | USART_CR1_RE | USART_CR1_OVER8), + tmpreg); + + /*-------------------------- USART CR3 Configuration -----------------------*/ + /* Configure the UART HFC: Set CTSE and RTSE bits according to huart->Init.HwFlowCtl value */ + MODIFY_REG(huart->Instance->CR3, (USART_CR3_RTSE | USART_CR3_CTSE), huart->Init.HwFlowCtl); + + +#if defined(USART6) && defined(UART9) && defined(UART10) + if ((huart->Instance == USART1) || (huart->Instance == USART6) || (huart->Instance == UART9) || (huart->Instance == UART10)) + { + pclk = HAL_RCC_GetPCLK2Freq(); + } +#elif defined(USART6) + if ((huart->Instance == USART1) || (huart->Instance == USART6)) + { + pclk = HAL_RCC_GetPCLK2Freq(); + } +#else + if (huart->Instance == USART1) + { + pclk = HAL_RCC_GetPCLK2Freq(); + } +#endif /* USART6 */ + else + { + pclk = HAL_RCC_GetPCLK1Freq(); + } + /*-------------------------- USART BRR Configuration ---------------------*/ + if (huart->Init.OverSampling == UART_OVERSAMPLING_8) + { + huart->Instance->BRR = UART_BRR_SAMPLING8(pclk, huart->Init.BaudRate); + } + else + { + huart->Instance->BRR = UART_BRR_SAMPLING16(pclk, huart->Init.BaudRate); + } +} + +/** + * @} + */ + +#endif /* HAL_UART_MODULE_ENABLED */ +/** + * @} + */ + +/** + * @} + */ + diff --git a/Makefile b/Makefile index ded8e214..034cbbac 100644 --- a/Makefile +++ b/Makefile @@ -1,5 +1,5 @@ ########################################################################################################################## -# File automatically-generated by tool: [projectgenerator] version: [4.1.0] date: [Tue Oct 24 14:15:18 EDT 2023] +# File automatically-generated by tool: [projectgenerator] version: [4.1.0] date: [Sun Nov 05 14:16:50 EST 2023] ########################################################################################################################## # ------------------------------------------------ @@ -49,6 +49,7 @@ Core/Src/stm32f4xx_hal_msp.c \ Core/Src/monitor.c \ Core/Src/fault.c \ Core/Src/can_handler.c \ +Core/Src/serial_monitor.c \ Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_can.c \ Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc.c \ Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_rcc_ex.c \ @@ -85,19 +86,13 @@ Middlewares/Third_Party/FreeRTOS/Source/tasks.c \ Middlewares/Third_Party/FreeRTOS/Source/timers.c \ Middlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2/cmsis_os2.c \ Middlewares/Third_Party/FreeRTOS/Source/portable/MemMang/heap_4.c \ -Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c +Middlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F/port.c \ +Drivers/STM32F4xx_HAL_Driver/Src/stm32f4xx_hal_uart.c # ASM sources ASM_SOURCES = \ startup_stm32f405xx.s -# Test source files -TEST_SOURCE_FILES = \ -Test/unity/tests/cerberus_test.c \ -Test/unity/tests/can_handler_test.c -# Unity source files and includes -UNITY_DIR = Test/unity/src -UNITY_SOURCES = $(UNITY_DIR)/unity.c ####################################### # binaries @@ -161,19 +156,6 @@ C_INCLUDES = \ -IDrivers/CMSIS/Device/ST/STM32F4xx/Include \ -IDrivers/CMSIS/Include -# test includes -UNITY_INCLUDES = \ --I$(UNITY_DIR) \ --ITest/unity/tests \ --ICore/Src \ --ICore/Inc \ --IDrivers/Embedded-Base/platforms/stm32f405/include \ --IDrivers/Embedded-Base/general/include \ --IDrivers/Embedded-Base/middleware/include \ --IMiddlewares/Third_Party/FreeRTOS/Source/include \ --IMiddlewares/Third_Party/FreeRTOS/Source/CMSIS_RTOS_V2 \ --IMiddlewares/Third_Party/FreeRTOS/Source/portable/GCC/ARM_CM4F - # compile gcc flags ASFLAGS = $(MCU) $(AS_DEFS) $(AS_INCLUDES) $(OPT) -Wall -fdata-sections -ffunction-sections @@ -232,15 +214,6 @@ $(BUILD_DIR)/%.bin: $(BUILD_DIR)/%.elf | $(BUILD_DIR) $(BUILD_DIR): mkdir $@ -####################################### -# run unit tests -####################################### -test: $(BUILD_DIR)/test_$(TARGET) - ./$(BUILD_DIR)/test_$(TARGET) -$(BUILD_DIR)/test_$(TARGET): $(TEST_SOURCE_FILES) $(UNITY_SOURCES) | $(BUILD_DIR) - gcc -D UNIT_TEST $(UNITY_INCLUDES) -o $@ $^ -####################################### - ####################################### # clean up ####################################### diff --git a/Test/renode/mpu.repl b/Test/renode/mpu.repl index 972347a6..54b7a749 100644 --- a/Test/renode/mpu.repl +++ b/Test/renode/mpu.repl @@ -1,4 +1,4 @@ -using "@test/renode/stm32f405.repl" +using "Test/renode/stm32f405.repl" imu: Sensors.LSM6DSO_IMU_I2C @ i2c1 0x35 //temp: I2C.SHT21 @ i2c1 0x40 diff --git a/cerberus.ioc b/cerberus.ioc index c881dc26..74ce8a7b 100644 --- a/cerberus.ioc +++ b/cerberus.ioc @@ -21,6 +21,7 @@ Mcu.CPN=STM32F405RGT6V Mcu.Family=STM32F4 Mcu.IP0=ADC1 Mcu.IP1=CAN1 +Mcu.IP10=USART3 Mcu.IP2=FREERTOS Mcu.IP3=I2C1 Mcu.IP4=I2C2 @@ -29,7 +30,7 @@ Mcu.IP6=RCC Mcu.IP7=SPI1 Mcu.IP8=SPI2 Mcu.IP9=SYS -Mcu.IPNb=10 +Mcu.IPNb=11 Mcu.Name=STM32F405RGTx Mcu.Package=LQFP64 Mcu.Pin0=PH0-OSC_IN @@ -141,8 +142,10 @@ PB8.Signal=CAN1_RX PB9.Mode=CAN_Activate PB9.Signal=CAN1_TX PC10.Locked=true +PC10.Mode=Asynchronous PC10.Signal=USART3_TX PC11.Locked=true +PC11.Mode=Asynchronous PC11.Signal=USART3_RX PC2.Mode=Full_Duplex_Master PC2.Signal=SPI2_MISO @@ -189,7 +192,7 @@ ProjectManager.ToolChainLocation= ProjectManager.UAScriptAfterPath= ProjectManager.UAScriptBeforePath= ProjectManager.UnderRoot=false -ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_CAN1_Init-CAN1-false-HAL-true,4-MX_I2C1_Init-I2C1-false-HAL-true,5-MX_I2C2_Init-I2C2-false-HAL-true,6-MX_SPI1_Init-SPI1-false-HAL-true,7-MX_SPI2_Init-SPI2-false-HAL-true +ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_CAN1_Init-CAN1-false-HAL-true,4-MX_I2C1_Init-I2C1-false-HAL-true,5-MX_I2C2_Init-I2C2-false-HAL-true,6-MX_SPI1_Init-SPI1-false-HAL-true,7-MX_SPI2_Init-SPI2-false-HAL-true,8-MX_ADC1_Init-ADC1-false-HAL-true,9-MX_USART3_UART_Init-USART3-false-HAL-true RCC.AHBFreq_Value=16000000 RCC.APB1Freq_Value=16000000 RCC.APB2Freq_Value=16000000 @@ -228,6 +231,8 @@ SPI2.Direction=SPI_DIRECTION_2LINES SPI2.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate SPI2.Mode=SPI_MODE_MASTER SPI2.VirtualType=VM_MASTER +USART3.IPParameters=VirtualMode +USART3.VirtualMode=VM_ASYNC VP_FREERTOS_VS_CMSIS_V2.Mode=CMSIS_V2 VP_FREERTOS_VS_CMSIS_V2.Signal=FREERTOS_VS_CMSIS_V2 VP_SYS_VS_Systick.Mode=SysTick diff --git a/cerberus.resc b/cerberus.resc index 3a9a1f09..e4b321f2 100644 --- a/cerberus.resc +++ b/cerberus.resc @@ -5,18 +5,20 @@ using sysbus mach create -machine LoadPlatformDescription @Test/renode/stm32f405.repl - i @Test/renode/LSM6DSO_IMU_I2C.cs i @Test/renode/STM32F4_I2C_NER.cs machine LoadPlatformDescription @Test/renode/mpu.repl -sysbus.cpu LogFunctionNames true -sysbus LogAllPeripheralsAccess true +# Uncomment to view callstack and peripheral access +#sysbus.cpu LogFunctionNames true +#sysbus LogAllPeripheralsAccess true sysbus.cpu PerformanceInMips 1 emulation SetGlobalQuantum "0.10000" +emulation CreateUartPtyTerminal "term" "/dev/ttyACM0" +connector Connect sysbus.usart3 term + sysbus LoadELF @build/cerberus.elf # Uncomment for autostart