Skip to content

Latest commit

 

History

History

uvmod_kitchen

Folders and files

NameName
Last commit message
Last commit date

parent directory

..
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Create your own custom rom for Quansheng UV-K5!

Prerequisites

How to use this?

  • customize included mods, for example mod_custom_freq_ranges.py has possibility to edit frequency ranges
  • edit build.bat, if you want omit execution of any mod, prefix its line with :: or rem
  • start command prompt in uvmod_kitchen directory
  • run command build.bat
  • look for any errors
  • now you can flash new firmware file named k5_v2.01.26_MODDED.bin (video by K5YVY)

List of mods

(not in any particular order)


mod_custom_font.py

Customization: Replace the font variable with the raw binary of a 1-bit, uncompressed bitmap that is interleaved as the firmware expects it (a modification to extract_font.py will be made for this purpose soon.)

Replaces the font bitmap with a custom font of your choosing

andrej_font.mp4

mod_custom_font_DO7OO.py

Similar as above but this time we are changing digits:

DO7OO_font.mp4

mod_custom_font_VCR.py

Changes only big digits to font VCR OSD Mono

vcrfont


mod_custom_bootscreen.py

Set up your custom boot logo image. Just like in old times of nokia 3310 😉 By default Q logo is set. To set up your own image paint a b&w bitmap image of size 128x64px then convert it to array using application like LCD Assistant

qs_logo


mod_custom_bootscreen_narrow.py

Basically same as above mod but allows to use smaller logo therefore less space at the end of the file. By default Do7oo logo is set. To set up your own image paint a b&w bitmap image of width 128px then convert it to array using application like LCD Assistant

Customization: before drawing logo, screen buffer is filled with value defined in clean_pattern variable. if you set it to 0xFF then screen will be filled "black", if 0x00 then screen will be clean.


mod_change_contrast.py

Customization:

# configure contrast in range from 0 to 63. Default value is 31
new_contrast = 31

Edits initialization routine of ST7565 (LCD controller) to change default LCD contrast


mod_custom_freq_ranges.py

The purpose of this mod is to give ability to user to select which ranges should be covered by each frequency range of quansheng radio or if to extend them at all. By default, file contains frequency ranges exactly like in stock firmware.

Customization:

# change below sets to new ones, values are in Hz
new_freq_low_limit =   [50_000_000, 108_000_000, 136_000_000, 174_000_000, 350_000_000, 400_000_000, 470_000_000]
new_freq_high_limit =  [76_000_000, 135_999_900, 173_999_900, 349_999_900, 399_999_900, 469_999_900, 600_000_000]

Here you can change low and high limit for each frequency band. The underscore _ symbol is omitted by python interpreter and is added only for better readability. So for example, if you want to fill the gap between 76 and 108Mhz then in second array change first limit from 76_000_000 to 107_999_990 or if you want to extend above 600MHz then change last limit from 600_000_000 to 1300_000_000. Please keep in mind that different ranges are demodulated slightly different inside BK4819 chip, and some ranges have enabled AM demodulation while other don't.


mod_custom_steps.py

Customization:

# change below sets to new ones, values are in Hz
new_freq_steps = [2500, 5000, 6250, 10000, 12500, 25000, 8330]

Changes array of frequency steps in menu at position 2


mod_enable_tx_50to850.py

No customization. You can just disable or enable it in build.bat. The purpose of this mod is to globally disable/bypass TX lock.

ℹ️ This patch alone doesn't extend available frequency ranges. For this use mod_custom_freq_ranges.py mod.


mod_mic_gain.py

No customization. You can just disable or enable it in build.bat. The purpose of this mod is to increase the base mic gain from 0 to 16, thus making all of the mic gain steps in the menu higher as a result.

A crude before (bottom) and after (top):

image

ℹ️ This patch doesn't extend available mic gain steps (they will still be 0-4.) It just increases the starting point on the mic gain scale sent to the BK4819 mic sensitivity register.


mod_negative_screen.py

No customization. You can just disable or enable it in build.bat.

Edits initialization routine of ST7565 (LCD controller) to change default LCD mode normal to negative.


mod_more_freq_steps.py

Customization:

# change below steps to new ones, values are in Hz
# You can add reasonably more steps here

new_freq_steps = [2500, 5000, 6250, 10000, 12500, 25000, 8330, 500000, 10, 1250, 20000]

Append new, bigger tablie with frequency steps at the end of firmware thus expanding it, but as far as we are below 0xF000 then we should be fine. Please report any bugs as this is more experimental feature than others above.


mod_custom_noaa_freqs.py

Customization:

#first 10 PMR446 channels
new_noaa_table =   [446_006_250, 446_018_750, 446_031_250, 446_043_750, 446_056_250, 446_068_750, 446_081_250, 446_093_750, 446_106_250, 446_118_750,  ]

Just sets new values for frequencies in NOAA scan list, nothing less, nothing more.


mod_disable_tx_completely.py

No customization.

On ALL frequencies radio shows "DISABLED" info and don't transmit at any band.

ℹ️ Please do not use this mod together with mod_enable_tx_50to850.py


mod_enable_tx_50to850_except_airband.py

Customization:

# set values to block band
block_freq_lo = 118_000_000
block_freq_hi = 137_000_000

By default block frequencies between 118 and 137MHz.

ℹ️ Please do not use this mod together with mod_enable_tx_50to850.py or mod_disable_tx_completely.py


mod_ota_qrg.py

Customization:

AIR_COPY_FREQ_HZ = 433_600_000

Default value for copying setting over the air aka "AIR COPY" is 410.025 MHz. You can change that default value using this mod.

aircopy