ZBBridge support for Honeywell Smoke Detector (JTYJ-GD-01LM/BW)

[Riza-Aslan]

PROBLEM DESCRIPTION

A clear and concise description of what the problem is.
I've added some Xiaomi Honeywell Smoke Detectors to my ZBBridge and it receives the smokedensity, batterypercentage and linkquality, but it should also have a channel for "smoke" with a value of true or false. This doesn't show up while pairing the device.

REQUESTED INFORMATION

Make sure your have performed every step and checked the applicable boxes before submitting your issue. Thank you!

• Read the Contributing Guide and Policy and the Code of Conduct
• Searched the problem in issues
• Searched the problem in discussions
• Searched the problem in the docs
• Searched the problem in the chat
• Device used (e.g., Sonoff Basic): Snoff ZBBridge
• Tasmota binary firmware version number used: ZBBridge 9.2
  • Pre-compiled
  • Self-compiled
• Flashing tools used: _____
• Provide the output of command: Backlog Template; Module; GPIO 255:

  Configuration output here:

• If using rules, provide the output of this command: Backlog Rule1; Rule2; Rule3:

  Rules output here:

• Provide the output of this command: Status 0:

  STATUS 0 output here:

• Set weblog to 4 and then, when you experience your issue, provide the output of the Console log:

  Console output here:

TO REPRODUCE

Steps to reproduce the behavior:
Add a JTYJ-GD-01LM/BW smoke detector. The smoke channel doesn't show up in the initialization process

EXPECTED BEHAVIOUR

A clear and concise description of what you expected to happen.

SCREENSHOTS

If applicable, add screenshots to help explain your problem.

ADDITIONAL CONTEXT

Add any other context about the problem here.

(Please, remember to close the issue when the problem has been addressed)

[ascillato]

Please, could you be so kind on completing the troubleshooting template in order to have more information so as to properly help you? And also please provide the logs requested in the template.

Remember to read the Contributing Guideline and Policy. Thanks.

---

Support Information

See Docs for more information.
See Chat for more user experience.
See Code of Conduct

[s-hadinger]

Especially, please provide weblog 3 level logs when the device reports values.

[Riza-Aslan]

I hope these are the right lines from the log, because my ZbBridge is communication pretty much:

14:34:55 ZIG: {"ZbZCLReceived":{"groupid":0,"clusterid":1280,"srcaddr":"0xA200","srcendpoint":1,"dstendpoint":1,"wasbroadcast":0,"LinkQuality":84,"securityuse":0,"seqnumber":98,"fc":"0x19","manuf":"0x0000","transact":2,"cmdid":"0x00","payload":"000000FF0000"}}
14:34:55 ZIG: ZbZCLRawReceived: {"0xA200":{"0500<00":"000000FF0000","ZoneStatusChange":0,"Endpoint":1,"LinkQuality":84}}
14:34:55 MQT: tele/Buero_Rauchmelder/SENSOR = {"ZbReceived":{"Buero_Rauchmelder":{"Device":"0xA200","Name":"Buero_Rauchmelder","0500<00":"000000FF0000","ZoneStatusChange":0,"Endpoint":1,"LinkQuality":84}}}
14:34:55 ZIG: {"ZbEZSPReceived":"4500000401000001010001000063B0C800A2FFFF2E18030A01FF422801210D0C03281C0421A80105215C00062402000000000A2100000821041064200196230000000002"}
14:34:55 ZIG: {"ZbZCLReceived":{"groupid":0,"clusterid":0,"srcaddr":"0xA200","srcendpoint":1,"dstendpoint":1,"wasbroadcast":0,"LinkQuality":81,"securityuse":0,"seqnumber":99,"fc":"0x18","manuf":"0x0000","transact":3,"cmdid":"0x0A","payload":"01FF422801210D0C03281C0421A80105215C00062402000000000A21000008210410642001962300000000"}}
14:34:55 ZIG: ZbZCLRawReceived: {"0xA200":{"0000/FF01":"01210D0C03281C0421A80105215C00062402000000000A21000008210410642001962300000000","Endpoint":1,"LinkQuality":81}}
14:34:55 MQT: tele/Buero_Rauchmelder/SENSOR = {"ZbReceived":{"Buero_Rauchmelder":{"Device":"0xA200","Name":"Buero_Rauchmelder","BatteryVoltage":3.09,"BatteryPercentage":100,"SmokeDensity":1,"Endpoint":1,"LinkQuality":81}}}

[Riza-Aslan]

Sure:

14:46:52 CMD: ZbInfo 0xA200
14:46:52 SRC: WebConsole from 10.14.8.151
14:46:52 CMD: Group 0, Index 1, Command "ZBINFO", Data "0xA200"
14:46:52 MQT: tele/Buero_Rauchmelder/SENSOR = {"ZbInfo":{"Buero_Rauchmelder":{"Device":"0xA200","Name":"Buero_Rauchmelder","IEEEAddr":"0x00158D0002B2246C","ModelId":"lumi.sensor_smoke","Manufacturer":"LUMI","Endpoints":[1],"Config":["I01","A01.3"],"ZoneType":40,"ZoneStatus":0,"Reachable":true,"BatteryPercentage":100,"LastSeen":468,"LastSeenEpoch":1614343144,"LinkQuality":0}}}
14:46:52 MQT: stat/ZigBee2Tasmota/RESULT = {"ZbInfo":"Done"}

[s-hadinger]

Thanks. What version of Tasmota are you using?

[s-hadinger]

I see 9.2 above. Please try 9.3, it should be fixed in 9.3

[Riza-Aslan]

The pre compiled tasmota-zbbridge.bin release 9.2.0
I've just seen that there is a new release. Should I update to 9.3.1 first?

[Riza-Aslan]

Okay...great. But should I really take 9.3 or better 9.3.1?

[Riza-Aslan]

I've just updated to 9.31 now

ZbInfo 0xA200 tells me now:

15:06:43.190 CMD: Group 0, Index 1, Command "ZBINFO", Data "0xA200"
15:06:43.199 MQT: tele/ZigBee2Tasmota/Buero_Rauchmelder/SENSOR = {"ZbInfo":{"Buero_Rauchmelder":{"Device":"0xA200","Name":"Buero_Rauchmelder","IEEEAddr":"0x00158D0002B2246C","ModelId":"lumi.sensor_smoke","Manufacturer":"LUMI","Endpoints":[1],"Config":["I01","A01.3"],"ZoneType":40,"ZoneStatus":0,"Reachable":true,"BatteryPercentage":100,"LastSeen":54,"LastSeenEpoch":1614344749,"LinkQuality":0}}}
15:06:43.204 MQT: stat/ZigBee2Tasmota/RESULT = {"ZbInfo":"Done"}

If I push the button, I'm getting the following log entry:

15:05:49.539 ZIG: ZbZCLRawReceived: {"0xA200":{"0500<00":"000000FF0000","ZoneStatusChange":0,"0500/FFF3":0,"Endpoint":1,"LinkQuality":0}}
15:05:49.545 MQT: tele/ZigBee2Tasmota/Buero_Rauchmelder/SENSOR = {"ZbReceived":{"Buero_Rauchmelder":{"Device":"0xA200","Name":"Buero_Rauchmelder","0500<00":"000000FF0000","ZoneStatusChange":0,"Fire":0,"Endpoint":1,"LinkQuality":0}}}

I think that "Fire" should change to 1 if there is smoke detected, right?

[s-hadinger]

Yes. It is registered as a fire detector.

[Riza-Aslan]

Awesome. Thanks for your help!