Skip to content

Latest commit

 

History

History
118 lines (76 loc) · 7.06 KB

mac.md

File metadata and controls

118 lines (76 loc) · 7.06 KB
Raw

Installing operating system images on Mac OS

On Mac OS you can use the command line dd tool, or the graphical tool Etcher to write the image to your SD card.

Installing operating system images using Etcher

  • Connect the SD card reader with the SD card inside. Note that it must be formatted as FAT32.
  • Download Etcher and install it to your Mac's Applications folder.
  • Open Etcher.app, select the Raspberry Pi .img file you wish to write to the SD card from your Mac's hard drive.
  • After selecting the .img file in Step 1, you will now select the SD card you wish to write the .img file to.
  • Review your selections and click "Flash!" to begin writing data to the SD card. Once complete, you can eject the mounted SD card from your Mac using Finder.app.

(Mostly) graphical interface

  • Connect the SD card reader with the SD card inside. Note that it must be formatted as FAT32.

  • From the Apple menu, choose "About This Mac", then click on "More info...". If you are using Mac OS X 10.8.x Mountain Lion or newer, you will then need to click on "System Report".

  • Click on "USB" (or "Card Reader" if using a built-in SD card reader), then search for your SD card in the upper-right section of the window. Click on it, then search for the BSD name in the lower-right section. It will look something like diskn where n is a number (for example, disk4). Make sure you take a note of this number.

  • Unmount the partition so that you will be allowed to overwrite the disk. To do this, open Disk Utility and unmount it. Do not eject it. If you eject it, you will have to reconnect it. Note that on Mac OS X 10.8.x Mountain Lion, "Verify Disk" (before unmounting) will display the BSD name as /dev/disk1s2 or similar, allowing you to skip the previous two steps. Note down the number that appears after "disk", in this case the number "1".

  • From the terminal, run the following command:

    sudo dd bs=1m if=path_of_your_image.img of=/dev/rdiskn

    Remember to replace n with the number that you noted before!

    This will take a few minutes, depending on the image file size. You can check the progress by sending a SIGINFO signal (press Ctrl+T).

    • If this command fails, try using disk instead of rdisk:

      sudo dd bs=1m if=path_of_your_image.img of=/dev/diskn

This will take a few minutes, depending on the image file size. To check the progress open Activity Monitor, click the Disk tab and find the process with the name dd. If dd is not in the list, you may need to select All Processes from the View menu. The Bytes Read column will display the amount of data that has been read from the image. Compare that to the file size of the image to determine progress.

Command line

  • If you are comfortable with the command line, you can write the image to an SD card without any additional software. Open a terminal, then run:

    diskutil list

  • Identify the disk (not partition) of your SD card e.g. disk4, not disk4s1.

  • Unmount your SD card by using the disk identifier, to prepare it for copying data:

    diskutil unmountDisk /dev/disk<disk# from diskutil>

    where disk is your BSD name e.g. diskutil unmountDisk /dev/disk4

  • Copy the data to your SD card:

    sudo dd bs=1m if=image.img of=/dev/rdisk<disk# from diskutil>

    where disk is your BSD name e.g. sudo dd bs=1m if=2017-03-02-raspbian-jessie.img of=/dev/rdisk4

    • This may result in a dd: invalid number '1m' error if you have GNU coreutils installed. In that case, you need to use a block size of 1M in the bs= section, as follows:

      sudo dd bs=1M if=image.img of=/dev/rdisk<disk# from diskutil>

    This will take a few minutes, depending on the image file size. You can check the progress by sending a SIGINFO signal (press Ctrl+T).

    • If this command still fails, try using disk instead of rdisk, for example:

      sudo dd bs=1m if=2017-03-02-raspbian-jessie.img of=/dev/disk4

      or

      sudo dd bs=1M if=2017-03-02-raspbian-jessie.img of=/dev/disk4

Alternative method

Note: Some users have reported issues with using this method to create SD cards.

These commands and actions need to be performed from an account that has administrator privileges.

  • From the terminal run df -h.

  • Connect the SD card reader with the SD card inside.

  • Run df -h again and look for the new device that was not previously listed. Record the device name of the filesystem's partition, for example /dev/disk3s1.

  • Unmount the partition so that you will be allowed to overwrite the disk:

    sudo diskutil unmount /dev/disk3s1

    Alternatively, open Disk Utility and unmount the partition of the SD card. Do not eject it. If you eject it, you will have to reconnect it.

  • Using the device name of the partition, work out the raw device name for the entire disk by omitting the final s1 and replacing disk with rdisk. This is very important, as you will lose all data on the hard drive if you provide the wrong device name. Make sure the device name is the name of the whole SD card as described above, not just a partition of it: for example, rdisk3, not rdisk3s1. Similarly, you might have another SD drive name/number like rdisk2 or rdisk4. You can check again by using the df -h command both before and after you insert your SD card reader into your Mac. For example: /dev/disk3s1 becomes /dev/rdisk3.

  • In the terminal, write the image to the card with this command, using the raw device name from above. Read the above step carefully to make sure that you use the correct rdisk number here:

    sudo dd bs=1m if=2017-03-02-raspbian-jessie.img of=/dev/rdisk3

    If the above command reports the error dd: bs: illegal numeric value, change the block size bs=1m to bs=1M.

    If the above command reports the error dd: /dev/rdisk3: Permission denied, the partition table of the SD card is being protected against being overwritten by Mac OS. Erase the SD card's partition table using this command:

    sudo diskutil partitionDisk /dev/disk3 1 MBR "Free Space" "%noformat%" 100%

    That command will also set the permissions on the device to allow writing. Now try the dd command again.

    Note that dd will not provide any on-screen information until there is an error or it is finished. When the process is complete, information will be shown and the disk will re-mount. If you wish to view the progress, you can use Ctrl-T. This generates SIGINFO, the status argument of your terminal, and will display information on the process.

  • After the dd command finishes, eject the card:

    sudo diskutil eject /dev/rdisk3

    Alternatively, open Disk Utility and use this to eject the SD card.

This article uses content from the eLinux wiki page RPi_Easy_SD_Card_Setup, which is shared under the Creative Commons Attribution-ShareAlike 3.0 Unported license