Update interval with 21s Timeout #110
-
|
Hello, great work. Thank you very much. I have a problem with the timeout. I have set it to 9s and the log says the following: [17:00:56][I][CYCLE:038]: 1: Cycle start What could be the problem? |
Beta Was this translation helpful? Give feedback.
Replies: 10 comments 16 replies
-
Hello, thanks,
A timeout occurs when a cycle in interrupted. This means your heatpump did not reply to one of the request.
Thanks for your feedback. Don't hesitate if you need more assistance. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you very much for the quick reply.
It looks like there is no communication. But I can control the air conditioning via Home Assistant (with a long delay). I can also see in Home Assistant when I control the air conditioning via the normal remote control (also with a long delay). |
Beta Was this translation helpful? Give feedback.
-
|
Ok thanks.
|
Beta Was this translation helpful? Give feedback.
-
|
ok I know this chip.
esp8266:
board: d1_mini
|
Beta Was this translation helpful? Give feedback.
-
|
Ah ok. Do you think a capacitor between the 3.3 volt pin and the ground pin could solve the problem? I used this module because I still had it. I would like to install it in two other indoor climate units. Would you recommend another module? Possibly one with ESP32? |
Beta Was this translation helpful? Give feedback.
-
|
I'm not a hardware specialist. I can't reply your question about the capacitor. For the chip, I like the esp32 as I did not meet any trouble with them. |
Beta Was this translation helpful? Give feedback.
-
|
So, OK. The capasitors didn't help. Now I use a ESP32 (https://www.makershop.de/plattformen/nodemcu/espressif-esp32-dev-kit-board/) and the log says: What is now the problem? |
Beta Was this translation helpful? Give feedback.
-
|
Hey @FaGerstenlauer ! The default UART is used by the ESPHOME logger. Or like discussed here : #63 (comment) Try this: logger: |
Beta Was this translation helpful? Give feedback.
-
|
Ah, I was thinking wrong. |
Beta Was this translation helpful? Give feedback.
-
|
Still the same Problem with the ESP32 than with the D1 Mini NodeMcu ESP8266-12F. :-( INFO ESPHome 2024.5.5 |
Beta Was this translation helpful? Give feedback.
-
I think you should have a yaml looking at this one: Also, could you take a picture of your circuit ? |
Beta Was this translation helpful? Give feedback.
-
|
The cable should be ok. If I interpret the log correctly, then it is receiving something, isn't it?
|
Beta Was this translation helpful? Give feedback.
-
|
Yes you're right. I have not read the logs well. It looks like the power request fails. |
Beta Was this translation helpful? Give feedback.
-
I can't get it to work. What is this? |
Beta Was this translation helpful? Give feedback.
-
Can this be deactivated? |
Beta Was this translation helpful? Give feedback.
-
|
not for the moment. |
Beta Was this translation helpful? Give feedback.
-
|
What is strange is that with the ESP8266 I was able to operate the air conditioning (with very very long feedback). Now, with the ESP32, nothing works.
|
Beta Was this translation helpful? Give feedback.
-
|
yes, it is strange. could you try this please: external_components:
source: github://echavet/MitsubishiCN105ESPHome@echavet/issue112You should have the following behaviour:
Of course, I can't test it in my config. So I'm waiting your feedback before merging the pull request. |
Beta Was this translation helpful? Give feedback.
-
Yes it works. INFO Upload took 6.54 seconds, waiting for result... |
Beta Was this translation helpful? Give feedback.
-
I think this was a Home Assistant Bug. The "silent" mode is not working. It always jumps automatically to “auto”. |
Beta Was this translation helpful? Give feedback.
-
|
Sorry, yes, this is an error in the esp32-test.yaml commit. You can't use
the local component option.
Le sam. 8 juin 2024, 15:36, FaGerstenlauer ***@***.***> a
écrit :
… I think you should have a yaml looking at this one:
https://github.com/echavet/MitsubishiCN105ESPHome/blob/main/esp32-test.yaml
I can't get it to work. What is this?
# this setting is for local component (code is not on github)
external_components:
- source:
type: local
path: components
—
Reply to this email directly, view it on GitHub
<#110 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AAYTHBH6GN4GKWAIXVNA5TDZGMCF5AVCNFSM6AAAAABIUHCGGKVHI2DSMVQWIX3LMV43SRDJONRXK43TNFXW4Q3PNVWWK3TUHM4TOMJTG4YTI>
.
You are receiving this because you were mentioned.Message ID:
<echavet/MitsubishiCN105ESPHome/repo-discussions/110/comments/9713714@
github.com>
|
Beta Was this translation helpful? Give feedback.
ok I know this chip.
https://www.amazon.fr/gp/product/B07CPXVDDN/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1