Items should be sorted roughly in order of most to least important, with model-specific changes at the bottom. Most items should use one of these formats:
- Breaking change:
- Added
- Fixed
- Removed
- Changed
- Documented
- &brand-model: Hardware-specific change (NNNN, NNNN, ...)
General:
- Smooth steps now work in Lockout Mode, if enabled.
- Made eeprom access more reliable, by waiting for power to stabilize before reads and writes.
- Increased voltage resolution to 0.02V. It can, for example, read out 1.20V, 1.22V, 1.24V, 1.26V, 1.28V, or 1.30V.
- Added weak battery detection, to limit power on alkaline, on empty cells, and while powered by a flashing adapter. Should prevent cell overload and magic smoke. Weak battery mode blinks 3X at boot. (d3aa only, so far)
- Made dark "blip"s work better on some types of regulators.
- Fixed bug: 3C in Tactical Mode would change the channel when it shouldn't.
- Fixed bug: Aux channels were off/off/high for levels 0/1/2. Now uses off/low/high.
- Misc improvements to the build process. Can build with Tactical Mode without Momentary Mode. Can build with newer avr-libc. Version strings calculated better now. Github actions can be run manually.
- Documentation updates.
New lights:
- Added &hank-emisar-2ch-fet-joined, for the lighted-switch variant of the D4S. It uses a 2-channel driver with only 1 channel of LEDs. (0137)
- Added &hank-emisar-d3aa, the first "3rd generation" torch (avr32dd20, thefreeman HDR driver). (0161)
- Added &fireflies-pl47g2-219, a reduced-power version of the PL47G2.
Hardware-specific changes:
- &lumintop-fw3x-lume1: Reduced visible pulsing on low modes.
This release is somewhat higher risk than usual, because so many large things changed deep in the code. I did major restructuring and refactoring across the entire project. It should work fine, but be on the lookout for any weird problems.
General:
- Moved from Bzr + Launchpad to Git + GitHub, by popular request.
- Completely reorganized the project files. Really, a massive amount of restructuring. The flashlight end-user interface is still the same, but expect to have to learn the code layout from scratch. Read the [README.md] for info about getting started with the new project layout.
- Added support for AVR DD MCUs like avr32dd20. This is the recommended MCU to use in new flashlights.
- Added ability to use turbo in momentary mode.
- Upgraded battery voltage resolution from 0.1V steps to 0.025V steps. Battery check has an extra digit which can be 0, 2, 5, or 7 (for example, for 3.70V, 3.725V, .3.75V, and 3.775V).
- Made Battery Check more consistent, so it's less likely to give different values on the 1st and 2nd readout.
- Re-calibrated timing on each MCU type, so a 1-second beacon flasher should be closer to 1 actual second now... mostly. Timing still varies significantly from one light to another.
- Fixed default bike flasher brightness on some builds. It was sometimes way too high.
- Fixed RGB aux turning on during momentary mode sometimes.
- Converted documentation to markdown format, and rewrote a lot of it.
- Fixed some build issues with specific compile-time options.
- Changed the format of version numbers. It now uses the most recent
release tag instead of the build date, and may have additional numbers at
the end to indicate distance from the last official release, and whether
the repo was clean or dirty. Today's release is
MODEL-2023-12-03. A derivative built 52 commits later in a dirty repo would look likeMODEL-2023-12-03-52-1.
New lights:
- Added &thefreeman-avr32dd20-devkit. It's only used for development purposes, but otherwise it's pretty neat. It'll be the basis for many new lights in the future. (model 1632dd20)
Hardware-specific changes:
- Improved idle efficiency on attiny1616, which was spending entirely too much time doing math it didn't actually need.
- &hank-*-boost: Fixed flicker while holding button at moon level. Reduced ripple on low modes. (0216, 0253, 0273)
- &lumintop-blf-gt: Added smooth steps. Removed a couple other things to make room. (0321)
- &lumintop-fw3x: Multiple fixes and upgrades... (0314, 0315)
- Fixed thermal regulation. Also fixed the external temperature sensor.
- Made moon much lower, and made ramp much smoother, by upgrading to DSM.
- Fixed the aux RGB pinouts because Lumintop got the wiring backward.
- Added a second build target for people who fixed the wires manually.
- Added red/blue police color strobe.
- Made low modes more efficient with underclocking. Moon should run at least 4X as long as it did before.
- Fixed party strobe being blurry.
- Added documentation for the FW3X's multiple, uh, quirks.
- &sofirn-lt1s-pro: Disabled manual memory, memory timer, and extended simple UI by default. Simple mode is simpler, and the factory settings should be more consistent with other lights now. (0623)
General:
- Finally finished converting all lights to the multi-channel API. (but a few are untested due to hardware being unavailable)
- Enabled smooth steps on almost all supported lights, including old ones. (in some cases, on old t85 lights, some other things may have been removed to make room)
- Made smooth steps work better, and fixed several bugs.
- Added/fixed RGB aux voltage on dual-fuel AA/li-ion drivers.
- Fixed delay timing on all supported MCUs, so 1 "second" is closer to an actual second (like in beacon mode or biking mode). (especially attiny1616, which was 17% too slow)
- Raised default thermal limit to 50C on attiny1616-based lights, since it doesn't need as big an error margin as older MCUs.
- Fixed missing item in globals menu on some lights.
- Misc internal improvements and per-light tweaks.
- Added a ChangeLog.md, to periodically summarize changes in a format which is more readable than the raw commit logs.
New lights:
- &thefreeman-boost21-6a: Added. (1631) (very nice HDR boost driver which fits into a FW3A)
- &thefreeman-boost-fwaa: Added. (1632) (very nice AA/li-ion HDR boost driver which fits into a FWAA)
Hardware-specific changes:
-
Upgraded several builds to use delta-sigma modulation (DSM), for lower lows and smoother ramping with less flicker or ripple:
- &blf-lt1 (0621)
- &blf-lt1-t1616 (0622)
- &emisar-d4k-3ch (0151) (dramatically improves resolution and low modes on its 8-bit channel)
- &noctigon-dm11-boost (0273)
- &noctigon-kr4-boost (0216)
- &noctigon-k1-boost (0253)
- &noctigon-m44 (0143)
-
Upgraded some builds to use dynamic PWM, for lower lows and smoother ramping:
- &blf-q8-t1616, &sofirn-sp36-t1616 (0613, 0614)
- &gchart-fet1-t1616 (1618)
- &noctigon-k1-sbt90 (0252)
-
&wurkkos-ts10, &wurkkos-ts10-rgbaux: Fixed too-high default ceiling. (0713, 0714)
General:
- Updated a bunch of lights to work with the new multi-channel API.
- Added "smooth steps" a.k.a. "soft start", to make on/off and step changes smooth. (enabled by default, can be turned off in Ramp Extras menu)
- User can save a different channel mode for each strobe-group mode.
- Made strobes/blinkies more responsive in Tactical Mode.
- Fixed bug: Tactical Mode clobbers strobe group memory.
- Fixed some minor post-off voltage display bugs.
- Made RGB button brightness update faster in blinky modes.
- Fixed bug: Wrong channel after colored factory reset.
- &attiny1616, &attiny1634: Partially fixed oscillating aux LED voltage colors while off. Better than before, but can still happen in some cases.
- &attiny1616: Fixed spurious voltage warnings in sleep mode. (it could sometimes go from Lockout mode to Off mode by itself)
- Lots of internal refactoring.
New lights:
- &emisar-2ch-fet: Added. (0136)
- &emisar-d4k-3ch: Added. (0151)
- &noctigon-m44: Added. (0143)
- &wurkkos-ts10-rgbaux: Added. (0713)
Hardware-specific changes:
- &ff-e01, &ff-pl47, &ff-pl47g2: Enabled smooth steps instead of SOS mode. (0421, 0422, 0423, 0441)
- &emisar-2ch, &noctigon-m44: Added RGB aux channel modes. (0135, 0143)
- &emisar-2ch-fet, &noctigon-k9.3: New ramps with better-calibrated shape. (0136, 0261)
- &emisar-d4v2-nofet: New ramp table. (0115)
- &emisar-d4sv2-tintramp: Removed / renamed. (0135, 0136)
- &noctigon-k9.3: Fixed years-old mess. Merged builds, converted to multi-channel, removed old builds, generally got K9.3 working quite a bit better. (0261, 0262, 0263, 0265, 0266, 0267)
- &noctigon-m44: Lower moon, and greatly reduced flicker. (0143)
- &sofirn-lt1s-pro: Allow configuring the blink channel. (0623)
- &wurkkos: Raised default temperature limit to 50 C. (07xx)
- &wurkkos-ts10: Better / smoother ramp. (0713, 0714)
- Fixed red aux blink on 1st frame of post-off voltage display
- Removed Harry Potter references because its author (J.K. Rowling) spreads hate
- &noctigon-kr4: Fixed thermal regulation (0211, 0212, 0213, 0214, 0215, 0216)
- Breaking change: Changed version check from YYYYMMDDXXXX to XXXX.YYYY-MM-DD, where the punctuation makes a "buzz" instead of number blinks.
- Fixed issue where some lights always thought they were overheating (when cold, or after a factory reset)
- Fixed aux pre-flash
- Fixed a rare corner case where gradual brightness adjustments stopped at 99% power instead of 100% power while going up from level 149/150 to 150/150 on some lights
- Changed "0" digit readout to use the same timing as other short blinks, to help ensure it works on all lights.
- Minor code changes with no runtime impact
- Documented new version check format
- &wurkkos: Added red+blue police strobe (0715, 0716, 0717)
- &noctigon-kr4: Broke thermal regulation (oops) (0211, 0212, 0213, 0214, 0215, 0216)
- &noctigon-kr4: Use 7 aux channel modes instead of 3 (0211, 0212, 0213, 0214, 0215, 0216)
- &emisar-d4v2: Changed number blinks from aux to main LEDs by default (0113, 0114, 0115, 0123)
- &noctigon-dm11-12v: Renamed to noctigon-dm11-boost (0273)
- &noctigon-dm11-boost: Now supported in multi-channel branch (0273)
- Added ability to set channel mode for number readouts (batt check, temp check, version check). Press 3C in batt check mode to change the blink channel.
- Changed post-off voltage display:
- Display for 4s by default, not 5s
- Made timing user-configurable in battcheck 7H menu item 2 (1 click per second the display should last)
- Use low brightness when torch was at moon level before
- Skip the voltage display after UI actions which didn't change the mode (like "Off -> 7C" to change aux LED settings)
- Changed RGB button behavior: While torch is on, use low mode below a configured level for real-time voltage color display, instead of always using high mode
- Fixed bug: Channel change could stick when activating a config menu from battcheck (the blink function changed the channel, then the config menu saved it, then the blink function restored it, then the config menu restored it to the value it saved, which was wrong)
- Documented ramp 6C, ramp 4C, ramp 4H, lockout 3H, battcheck 3C, and post-off voltage display config
- &emisar-d4v2: Added the rest of the aux RGB colors as channel modes, and set aux "white" as the mode it uses to blink out numbers (0113, 0114, 0115, 0123)
- &wurkkos-ts10: Converted to multi-channel, and gave it a new ramp with better low modes (0714)
- &wurkkos-ts25: Converted to multi-channel, and gave it a smoother ramp (0715)
- &wurkkos: Added Wurkkos FC13 and TS11 (0716, 0717)
- Changed lockout mode:
- Fixed manual memory timer and tint
- Added 3H for next channel (to change channels without unlocking, was possible before but needed to be updated for the new channel system)
- Made 3H+ use mem level instead of lowest moon (this is needed for making the channel discernible, and also helps make aux LED controls stand out more)
- &emisar, &noctigon: Added Extended Simple UI to Hank's config, so a few more features are allowed in simple mode
- &emisar-d4v2, &noctigon-kr4: Slightly smaller ROM size
- &emisar-d4sv2: Converted to multi-channel, and updated it to use dynamic PWM for a smoother ramp with lower lows (0133, 0134)
- &noctigon-kr4: Converted to multi-channel (0211, 0212, 0213, 0214)
- &noctigon-kr4: Don't blink at top of regulated power (0211, 0213, 0214)
- Added voltage display (by color) on RGB aux LEDs after turning the main LEDs off
- Changed RGB aux: Always preview in high mode while changing color or pattern
- Changed default RGB aux color in lockout mode: Uses blinking voltage, instead of blinking disco (unless model-specific config defines a different default)
- Changed tactical mode default config: only use 2-color strobe if it's on main LEDs, not aux LEDs
- &emisar-d4v2: Smoother ramp (0113, 0114)
- &emisar-d4v2: Added hidden channel modes for RGB aux LEDs (0113, 0114, 0115)
- Changed channel mode menu to preview channels during configuration
- Changed tactical mode default config: use 2-color police strobe if it exists, instead of single-color strobe
- Fixed unnecessary flickering when changing channel modes from/to the same value
- Fixed sleep voltage measurement on attiny1616
- &noctigon-kr4-tintramp: Converted to multi-channel, renamed to noctigon-kr4-2ch (0215)
- Fixed old old bug(s) with voltage measurement while asleep, while also
adding other improvements:
- Fixed oscillating RGB aux colors while asleep in voltage mode, mostly.
Some much smaller oscillations are still possible, but the primary issue has been fixed, I think. - Fixed old old bug which could cause spurious low-voltage warnings while asleep (previously required a messy code workaround).
- Reduced avg standby power by ~15uA.
- Now measures voltage every 1s instead of 8s while asleep.
- Changed RGB aux behavior: Puts aux LEDs in high mode for 3 seconds after light goes to sleep (much easier to see the voltage this way) (this change was obsoleted soon by a better post-off voltage display)
- Broke sleep voltage measurement on attiny1616 (oops)
- Fixed oscillating RGB aux colors while asleep in voltage mode, mostly.
- Changed internal details for how gradual ramping works
- &emisar-d4sv2-tintramp: Converted to multi-channel, renamed to emisar-2ch. (0135)
- &sofirn-lt1s-pro: Updated to use today's new code internals (0623)
- Added stepped tint ramping
- Documented new channel modes system
- &sofirn-lt1s-pro: Added white-only auto-tint mode (0623)
- Need to import old commit logs as changelog items