Skip to content

Latest commit

 

History

History
126 lines (84 loc) · 3.95 KB

usage.md

File metadata and controls

126 lines (84 loc) · 3.95 KB

NCTL Usage

Once activated, NCTL commands can be used to set up & control nodes within a local test network. Most NCTL users will be testing a single local network, however developers wishing to test multiple networks in parallel may do so. This usage guide focuses upon the former use case, i.e. testing a single network, and thus all NCTL commands described below are executed with their default values. Please refer here for full details of supported NCTL commands.

Step 1: Compile network binaries

Prior to testing a network ensure that the binary sets are available:

nctl-compile

This runs make setup-rs, and compiles casper-node, casper-client and casper-node-launcher in release mode.

NOTE

Ensure you are checked out to the correct branch of each of the three repositories above. Generally this will be dev (or your working branch recently forked from dev) for casper-node and casper-client-rs, and main for casper-node-launcher.

Step 2: Create network assets

  • Once network binary compilation is complete we need to set up test network assets. The following command instantiates the full set of assets required to run a 5 node local network with 5 users. It also creates the assets for a further 5 nodes in order to test join/leave scenarios. The assets are copied to $NCTL/assets/net-1, where $NCTL is the nctl home directory.
nctl-assets-setup
  • Examining the contents of $NCTL/assets/net-1 you will observe the following (self-explanatory) sub-folders:
/bin
/chainspec
/daemon
/faucet
/nodes
/users
  • Examining the contents of $NCTL/assets/net-1/nodes/node-1, i.e. node 1, you will observe the following (self-explanatory) sub-folders:
/bin
/config
/keys
/logs
/storage
  • Examining the contents of $NCTL/assets/net-1/users/user-1, i.e. user 1, you will find both cryptographic keys & account public key (hex) files.

  • Once assets have been created you are advised to review contents of toml files, i.e. /chainspec/chainspec.toml & the various /nodes/node-X/config/node-config.toml files.

  • If you wish to test modifications to a network's chainspec, you can:

vi $NCTL/assets/net-1/chainspec/chainspec.toml
  • If you wish to test modifications to a node's config, e.g. node 3, you can:
vi $NCTL/assets/net-1/nodes/node-3/config/node-config.toml

Step 3: Start a node in interactive mode

  • Starting a node interactively is useful to verify that the network assets have been correctly established and that the network is ready for testing.
nctl-interactive

Step 4: Start a network in daemon mode

  • To start with all or a single node in daemonized mode (this is the preferred operating mode):
# Start all nodes in daemon mode.
nctl-start

# Start node 1 in daemon mode.
nctl-start node=1
  • To view process status of all daemonized nodes:
nctl-status
  • To stop either a single or all daemonized nodes:
# Stop all nodes.
nctl-stop

# Stop node 1.
nctl-stop node=1

Step 5: Dump logs & other files

Upon observation of a network behavioral anomaly you can dump relevant assets such as logs & configuration as follows:

# Writes dumped files -> $NCTL/dumps/net-1
nctl-assets-dump

Step 6: View information

You can view chain, faucet, node & user information using the set of nctl-view-* commands. See here for further information.

Step 7: End testing session

To teardown a network once a testing session is complete:

# Delete previously created assets and stops all running nodes.
nctl-assets-teardown

Summary

Using NCTL one can spin up either a single or multiple test networks. Each network is isolated in terms of its assets - this includes port numbers. The NCTL commands parameter defaults are set for the general use case of testing a single local 5 node network. You are encouraged to integrate NCTL into your daily workflow to standardize the manner in which the network is tested in a localized setting.