.rtorrent.rc

# This is an example resource file for rTorrent. Copy to
# ~/.rtorrent.rc and enable/modify the options as needed. Remember to
# uncomment the options you wish to enable.
#
# Based on original .rtorrent.rc file from http://libtorrent.rakshasa.no/
# Modified by Lemonberry for rtGui http://rtgui.googlecode.com/
#
# This assumes the following directory structure:
# 
# /Torrents/Downloading - temporaray location for torrents while downloading (see "directory")
# /Torrents/Complete - Torrents are moved here when complete (see "on_finished")
# /Torrents/TorrentFiles/Auto - The 'autoload' directory for rtorrent to use.  Place a file 
#           in here, and rtorrent loads it #automatically.  (see "schedule = watch_directory")
# /Torrents/Downloading/rtorrent.session - for storing rtorrent session information
#


done_fg_color = 6
#done_bg_color = 0
active_fg_color = 1
#active_bg_color = 0


# Maximum and minimum number of peers to connect to per torrent.
min_peers = 10
max_peers = 100

# Same as above but for seeding completed torrents (-1 = same as downloading)
min_peers_seed = 10
max_peers_seed = 50

# Maximum number of simultanious uploads per torrent.
max_uploads = 15

# Global upload and download rate in KiB. "0" for unlimited.
download_rate = 0
upload_rate = 100

# Default directory to save the downloaded torrents.
directory = /media/Data/torrents

# Default session directory. Make sure you don't run multiple instance
# of rtorrent using the same session directory. Perhaps using a
# relative path?
session = /home/kopri/rtorrent/.session

# Watch a directory for new torrents, and stop those that have been
# deleted.
schedule = watch_directory,5,5,load_start=/home/kopri/rtorrent/watch/*.torrent
schedule = untied_directory,5,5,stop_untied=
schedule = tied_directory,5,5,start_tied=
# Close torrents when diskspace is low. */
#schedule = low_diskspace,5,60,close_low_diskspace=100M


# Stop torrents when reaching upload ratio in percent,
# when also reaching total upload in bytes, or when
# reaching final upload ratio in percent.
# example: stop at ratio 2.0 with at least 200 MB uploaded, or else ratio 20.0
#schedule = ratio,60,60,stop_on_ratio=200,200M,2000



# When the torrent finishes, it executes "mv -n <base_path> ~/Download/"
# and then sets the destination directory to "~/Download/". (0.7.7+)


# The ip address reported to the tracker.
#ip = 127.0.0.1
#ip = rakshasa.no

# The ip address the listening socket and outgoing connections is
# bound to.
#bind = 127.0.0.1
#bind = rakshasa.no

# Port range to use for listening.
port_range = 55556-55560



# Start opening ports at a random position within the port range.
port_random = yes

# Check hash for finished torrents. Might be usefull until the bug is
# fixed that causes lack of diskspace not to be properly reported.
check_hash = yes

# Set whetever the client should try to connect to UDP trackers.
use_udp_trackers = yes
dht = auto
dht_port = 6881
peer_exchange = yes
# Alternative calls to bind and ip that should handle dynamic ip's.
#schedule = ip_tick,0,1800,ip=rakshasa
#schedule = bind_tick,0,1800,bind=rakshasa

# Encryption options, set to none (default) or any combination of the following:
# allow_incoming, try_outgoing, require, require_RC4, enable_retry, prefer_plaintext
#
# The example value allows incoming encrypted connections, starts unencrypted
# outgoing connections but retries with encryption if they fail, preferring
# plaintext to RC4 encryption after the encrypted handshake
#
encryption = allow_incoming,require,require_RC4

#
# Do not modify the following parameters unless you know what you're doing.
#

# Hash read-ahead controls how many MB to request the kernel to read
# ahead. If the value is too low the disk may not be fully utilized,
# while if too high the kernel might not be able to keep the read
# pages in memory thus end up trashing.
#hash_read_ahead = 10

# Interval between attempts to check the hash, in milliseconds.
#hash_interval = 100

# Number of attempts to check the hash while using the mincore status,
# before forcing. Overworked systems might need lower values to get a
# decent hash checking rate.
#hash_max_tries = 10

# Max number of files to keep open simultaniously.
#max_open_files = 128

# Number of sockets to simultaneously keep open.
#max_open_sockets = <no default>


# Example of scheduling commands: Switch between two ip's every 5
# seconds.
#schedule = "ip_tick1,5,10,ip=torretta"
#schedule = "ip_tick2,10,10,ip=lampedusa"

# Remove a scheduled event.
#schedule_remove = "ip_tick1"

#
# PyroScope SETTINGS
#

# Set "pyro.extended" to 1 to activate rTorrent-PS features!
# LEAVE THIS AT 0 IF YOU RUN A VANILLA rTorrent!
system.method.insert = pyro.extended, value|const, 1

# Set "pyro.bin_dir" to the "bin" directory where you installed the pyrocore tools!
# Make sure you end it with a "/"; if this is left empty, then the shell's path is searched.
system.method.insert = pyro.bin_dir, string|const, 

# Remove the ".default" if you want to change something (else your 
# changes get over-written on update).
#system.method.insert = pyro.rc_dialect, string|const|simple, "execute_capture=bash,-c,\"test $1 = 0.8.6 && echo -n 0.8.6 || echo -n 0.8.9\",dialect,$system.client_version="
#system.method.insert = pyro.rtorrent_rc, string|const|private, "$cat=~/.pyroscope/rtorrent-,\"$pyro.rc_dialect=\",.rc.default"
#import = $pyro.rtorrent_rc=

# TORQUE: Daemon watchdog schedule
# Must be activated by touching the "~/.pyroscope/run/pyrotorque" file!
# Set the second argument to "-v" or "-q" to change log verbosity.
schedule = pyro_watchdog,30,300,"pyro.watchdog=~/.pyroscope,"