Replies: 19 comments
-
|
Hi @ledneczki, It's probably best to start writing the I²S driver and ask any questions that come up here. To start with I²S for STM32F4 you should read STs reference manual (if not already done) and have a look at our I'm not sure how the API for I²S should look like, depending on this I see two options:
In both cases you will probably have to modify |
Beta Was this translation helpful? Give feedback.
-
|
Welcome @ledneczki, your contribution is very much appreciated. I am not sure trying to integrate I²S into the present On the other hand a lot of similar options with the same names exist that are configured in entirely different registers and have other sets of permitted values. This overload of terms would make a joined interface quite confusing to use. In my opinion, the best option to get started would be creating a low-level For designing the higher level interface on top of the Hal class, keep in mind that audio is hard-realtime. Any gap in transmissions will create unwanted click and pop noises. The buffer in the peripheral is just one sample for one channel (or half a sample in 24bit mode). For 48 kHz, 16 bit, 2 channel audio playback and 168 MHz F407 max. CPU clock it means you have to put a sample into the peripheral TX buffer every 1750 cpu cycles. Depending on your application and the kind of processing you do that could be challenging. That's why audio is mostly processed in units of blocks and not single samples. On the STM32 you would ideally use DMA in circular double-buffered mode. Then you have 2 buffers of which one can be filled by the application while the other one is being accessed by the I²S peripheral. Unfortunately, we don't support that (yet) for STM32F4. I would advise you to start without DMA unless absolutely necessary. It can be added in a second step. Don't be afraid to ask any questions. The modm code generation is quite different to what most people do and the documentation on that is not that extensive. Feel free to open a draft pull request early if you are stuck. |
Beta Was this translation helpful? Give feedback.
-
|
Thank you @rleh and @chris-durand for your great input! I will do according to your suggestions. I also agree that for audio, DMA is needed, but then let's start at the beginning and get that I2S peripheral up and running! |
Beta Was this translation helpful? Give feedback.
-
|
I didn't want to open a separate issue for STM32F407 DMA support. I don't know what I'm capable of in C++, so I can't say I could implement anything really. However, I need that. Should I change the MCU family I'm using, or was it a work in progress so it's worth to wait for it? |
Beta Was this translation helpful? Give feedback.
-
|
I am not aware of anyone working on that right now but I would guess it might happen with the I²S driver being there. What is your application you would like to use DMA for? Don't be discouraged if you would like to try implementing it yourself. The C++ side of it isn't actually that hard. I don't remember how different the F4 DMA is to the ones we support right now, I guess the main work is adapting the present driver to the hardware specifics. The API will be very similar. modm-devices already has the information for F4 on DMA streams and channels. We are here to help and are happy about features being added to modm. So if you would like to try it and need some hints to get started, please feel free to ask. At least I expect STM32G4 DMA to happen within the next 2 weeks because I have an application where it would be beneficial. |
Beta Was this translation helpful? Give feedback.
-
|
I'm have currently some uncommited changes on my computer trying to get DMA running on STM32F4/F7, but the code does not compile yet and is completely untested. I will focus in the next weeks to test it on a Nucleo-F429ZI. |
Beta Was this translation helpful? Give feedback.
-
|
What they^ said, plus also consider configuring DMA directly via the CMSIS, taking inspiration from our driver perhaps. It may be faster and better to understand for you, especially depending on your use-case. |
Beta Was this translation helpful? Give feedback.
-
Nice! Does STM32G4 use the dma-stream-channel or the dma-channel(-request) IP? |
Beta Was this translation helpful? Give feedback.
-
dma-mux like H7 |
Beta Was this translation helpful? Give feedback.
-
|
That's the spirit! You are very encouraging. Okay, I'll see what I can do. |
Beta Was this translation helpful? Give feedback.
-
I need to implement XY2-100 protocol in a faster way (bit banging is very slow ATM) which uses clock-data protocol in the data-link layer. It's just like SPI, but I need 3 MOSI and 2MISO channels. |
Beta Was this translation helpful? Give feedback.
-
|
Ok, but then the modm API won't help you much, you need to bit-bang this via timer-triggered DMA transfers to/from GPIO. You won't need the asynrchonous RX processing, you can read the GPIO synchronously with the clock, so it's a little easier for you. Note that only DMA2 can access the GPIO registers, and only Timer1 and Timer8 can trigger DMA2!!! |
Beta Was this translation helpful? Give feedback.
-
|
I am currently facing an obstacle, and I would need your help to clear it.
Still the discovery finishes and I can already see the I2S module, but currently no instances of the perhiperal are listed. I have found a file, called modm/ext/modm-devices/modm_devices/resources/devices/stm32/stm32f4-05_07_15_17.xml. Here I can see that the instaces are specified below this line: |
Beta Was this translation helpful? Give feedback.
-
|
Could you open a "Draft" Pull Request with your code? |
Beta Was this translation helpful? Give feedback.
-
|
You're probably missing a |
Beta Was this translation helpful? Give feedback.
-
|
I have opened a draft pull request, so you can see where I am standing now. @salkinium indeed, it was the problem. Thank you for the good hint! |
Beta Was this translation helpful? Give feedback.
-
|
FYI: I have a fully working example of GPIO pin usage via DMA: here. I'm going to port the DMA settings directly into my Modm code. |
Beta Was this translation helpful? Give feedback.
-
|
@ledneczki The DMA implementation for STM32F4 and STM32F7 is here: #629 |
Beta Was this translation helpful? Give feedback.
-
|
@rleh That sounds awesome! Audio projects would greatly benefint from it. Thanks for picking it up! In the meantime I am creating an example project that uses the external DAC on the STM32F4 Discovery board. |
Beta Was this translation helpful? Give feedback.
-
Hi modm Community!
I have a STM32F4 discovery board and I would like to do some audio related development on it. I came across your great embedded framework, and I would like to use it for my project. I see, that SPI driver is already implemented, but the I2S support is not there yet. So, I would like to add I2S support for this discovery board.
I saw on the modm website that before contributing it is advised to get in contact with you. What do you think about my initiative? Do you have some hints before starting implementing the driver?
Thank you in advance!
Beta Was this translation helpful? Give feedback.
All reactions