-
Notifications
You must be signed in to change notification settings - Fork 377
/
WHATSNEW.txt
1194 lines (1028 loc) · 63.9 KB
/
WHATSNEW.txt
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
512
513
514
515
516
517
518
519
520
521
522
523
524
525
526
527
528
529
530
531
532
533
534
535
536
537
538
539
540
541
542
543
544
545
546
547
548
549
550
551
552
553
554
555
556
557
558
559
560
561
562
563
564
565
566
567
568
569
570
571
572
573
574
575
576
577
578
579
580
581
582
583
584
585
586
587
588
589
590
591
592
593
594
595
596
597
598
599
600
601
602
603
604
605
606
607
608
609
610
611
612
613
614
615
616
617
618
619
620
621
622
623
624
625
626
627
628
629
630
631
632
633
634
635
636
637
638
639
640
641
642
643
644
645
646
647
648
649
650
651
652
653
654
655
656
657
658
659
660
661
662
663
664
665
666
667
668
669
670
671
672
673
674
675
676
677
678
679
680
681
682
683
684
685
686
687
688
689
690
691
692
693
694
695
696
697
698
699
700
701
702
703
704
705
706
707
708
709
710
711
712
713
714
715
716
717
718
719
720
721
722
723
724
725
726
727
728
729
730
731
732
733
734
735
736
737
738
739
740
741
742
743
744
745
746
747
748
749
750
751
752
753
754
755
756
757
758
759
760
761
762
763
764
765
766
767
768
769
770
771
772
773
774
775
776
777
778
779
780
781
782
783
784
785
786
787
788
789
790
791
792
793
794
795
796
797
798
799
800
801
802
803
804
805
806
807
808
809
810
811
812
813
814
815
816
817
818
819
820
821
822
823
824
825
826
827
828
829
830
831
832
833
834
835
836
837
838
839
840
841
842
843
844
845
846
847
848
849
850
851
852
853
854
855
856
857
858
859
860
861
862
863
864
865
866
867
868
869
870
871
872
873
874
875
876
877
878
879
880
881
882
883
884
885
886
887
888
889
890
891
892
893
894
895
896
897
898
899
900
901
902
903
904
905
906
907
908
909
910
911
912
913
914
915
916
917
918
919
920
921
922
923
924
925
926
927
928
929
930
931
932
933
934
935
936
937
938
939
940
941
942
943
944
945
946
947
948
949
950
951
952
953
954
955
956
957
958
959
960
961
962
963
964
965
966
967
968
969
970
971
972
973
974
975
976
977
978
979
980
981
982
983
984
985
986
987
988
989
990
991
992
993
994
995
996
997
998
999
1000
--- RELEASE-15.02.02 ---
This release fixes a bug that prevents revo onboard mag to work correctly.
Release Notes - OpenPilot - Version RELEASE-15.02.02
The full list of bugfixes in this release is accessible here:
https://progress.openpilot.org/issues/?filter=12262
** Bug
* [OP-1820] - fix onboard mag orientation
* [OP-1821] - Tricopter tail servo wrong speed on wizard
* [OP-1827] - Version ID wrong in Windows uninstaller
* [OP-1857] - PPM on Flexi does not work on CC/CC3D
** Task
* [OP-1831] - due to oneshot higher pid values ki now shows "red" warning in stabilization page
--- RELEASE-15.02.01 ---
This release fixes an in important bug that may prevent failsafe to work correctly using CC3D/CC with a PWM receiver.
The full list of bugfixes in this release is accessible here:
https://progress.openpilot.org/issues/?filter=12260
Release Notes - OpenPilot - Version RELEASE-15.02.1
** Bug
* [OP-1812] - CC3D : PWM: Does not go into failsafe when RX is pulled under 50% throttle
--- RELEASE-15.02 --- Ragin' Cajun ---
This release introduces major flight performance improvements, enhancements as well as bug fixes. Many enhancements have been made to reducing dead-time of the communication between the flight controller and ESCs. In our testing, we have found this to be not only the best flight performance so far in the OpenPilot project but the best flight performance of any project we have tested against. This is a recommended upgrade for everyone and the more skilled of a pilot you are, the more you will love this release.
A key improvement that helped achieve this was the addition of the PWMSync code path, this is now enabled by default. Some restrictions applies to CC3D/CC as it needs a compatible input method to enable PWMSync. Compatible input methods are PPM, S.Bus, DSM and OPLink. This release also introduces support for OneShot125 capable ESCs, such as the KISS ESCs and all ESCs supported in BLHeli V13 and above. Note that OneShot125 support has the same restrictions as PWMSync for CC and CC3D.
Note for CC3D/CC: To support PWMSync/OneShot125 PPM input pin has changed from earlier releases to the last pin on the input IO port, please refer to the connection diagram in the setup wizard to see the required new pin layout for PPM.
Other enhancements include key parts of the GCS translated to Chinese and further OPLink reliability additions allowing us to confidently say it can be used as a primary control link as well as for telemetry.
The full list of features, improvements and bugfixes in this release is accessible here:
https://progress.openpilot.org/issues/?filter=12161
Release Notes - OpenPilot - Version RELEASE-15.02
** Bug
* [OP-969] - Input Configuration Wizard has scrollbars showing up and next/previous buttons are pushed down out of sight
* [OP-1034] - CCPM Config Widget crashes GCS if required boxes aren't set i.e. Channel set to None
* [OP-1236] - Icons on Welcome tab - moves to the left
* [OP-1466] - Gcs crashes on Helicopter config tab
* [OP-1522] - Improve Robustness of OPLink radio
* [OP-1601] - Still not enough ram on CC for gps to be usable
* [OP-1644] - Radio Setup Wiz problem with 6 flight modes
* [OP-1670] - cruise control conflict with flight modes (rate & acro +)
* [OP-1680] - OPLink control limited to 1000-1896
* [OP-1682] - Overflow issue with pwm rx and CC3D
* [OP-1686] - Slave OPLM should receive PPM in PPM_only mode
* [OP-1706] - Output Reverse checkboxes tick them selves when min equals max
* [OP-1718] - FW vehicle setup wizard may strip servo gears
* [OP-1722] - libusb include is incorrect.
* [OP-1728] - FW servos ignore set neutral
* [OP-1733] - version-info.py should check for version-info.json not git repo.
* [OP-1735] - Build fails with a tilde (~) in path.
* [OP-1737] - Min/max will be greyed even if motor output test is canceled
* [OP-1741] - Repo path is incorrect in version_info.pro
* [OP-1743] - cc3d fails to connect once "next " is loaded 2-23-15
* [OP-1744] - Vehicle config wizard produces a bad configuration
* [OP-1754] - Vehicle Wizard bad config when setting PPM in and RapidESC out
* [OP-1755] - Add additional path for cloudconfigs
* [OP-1758] - Upgrade hidapi for all OSs (except windows) to solve mac issue:Fix incorrect device list after device removal
* [OP-1761] - Wizard bad config when PPM in, RapidESC out and hexa frame with CC/CC3D/Atom
* [OP-1764] - System should sanity check RC Input Channel value ranges and raise alarm accordingly
* [OP-1768] - PWM Sync and OneShot125 wizard output level and warning are incorrect
** Improvement
* [OP-1519] - Auto Reboot of board when required by Wizard
* [OP-1576] - Remove tx resent accounting from OPlink
* [OP-1635] - Remove Quad H from wizard to avoid confusion with Quad X
* [OP-1650] - Reduce telemetry to improve OPLink
* [OP-1658] - Sensor driver API and overhaul of sensor module
* [OP-1683] - Support synchronous (OneShot) and OneShot125 output mode
* [OP-1685] - Support OneShot/OneShot125 for CC* targets
* [OP-1694] - Make package make rule non-nested
* [OP-1698] - Add easy to set channel passtrough GCS functionality
* [OP-1704] - Add support for sanity check custom hooks
* [OP-1759] - Hide CC3D non-supported options (GPSAssist)
** New Feature
* [OP-1723] - RCCar Forward/reverse support
** Task
* [OP-1721] - C++ enable flight controller and upgrade ARM tools
* [OP-1738] - change default flight modes and thrust settings
* [OP-1747] - 15.02 rc1 motor end points do not reflect oneshot125 / pwmsync
** Sub task
* [OP-1748] - Chinese translation for 15.02
* [OP-1752] - Add Alarm sub status to SystemHealth
--- RELEASE-15.01 --- Look Ma, No hands ---
This release mainly focuses on a new feature, GPSAssist which is a new form of assisted control for multirotors.
Assisted Control provides assistance functions on top of existing flight modes. GPSAssist is the
first assisted control option available from OpenPilot. GPSAssist supports Attitude and Rattitude
flight modes and activates braking into position hold when the pitch/roll sticks are centered. Attitude/Rattitude
may be flown with any of the current thrust modes (manual, cruisecontrol, altvario). GPSAssist for the PositionHold
flight mode also introduces a braking sequence when first entering this flight mode and introduces altvario as the thrust mode.
The full list of features, improvements and bugfixes in this release is accessible here:
http://progress.openpilot.org/issues/?filter=12062
** Bug
* [OP-1501] - Input wizard sets neutral point for throttle too low
* [OP-1579] - Add LDFLAGS to Makefile sanitized variables
* [OP-1626] - Satellite dsm2/dsmX binding should depend on proper window timing.
* [OP-1638] - Transmitter setup can strip servo gears.
* [OP-1646] - QQmlExpression: Expression qrc:/welcome/qml/main.qml:125:23 depends on non-NOTIFYable properties:
* [OP-1647] - Welcome QML type error
* [OP-1653] - Qt 5.2.1 fixes
* [OP-1654] - Linux libs rpath incorrect
* [OP-1660] - RCinput manual calibration issue
* [OP-1662] - SystemHealt more verbose
* [OP-1681] - Fix debug build of GCS
* [OP-1699] - Fix build issue with tagged linux release
* [OP-1701] - Fix linux Qt path config
** Improvement
* [OP-1071] - Make map "emergency" lines less strong and dashed
* [OP-1256] - Add Erase Settings step to Vehicle Setup Wizard
* [OP-1496] - Qt5.3.2 for OSX
* [OP-1599] - rework position vario modes
* [OP-1607] - Tab scaling on Vehicle Configuration pages is affected by clicking on "Ground" vehicle.
* [OP-1611] - Add context menu to Scopes gadget.
* [OP-1620] - Add fixed-wing Vtail to setup wizard
* [OP-1622] - Update Ground config tab
* [OP-1628] - Remove need to manually reboot by unplugging USB cable
* [OP-1629] - Add erase settings check box (default checked) to wizard firmware page
* [OP-1652] - Rename WS2811_LED_Out pins
* [OP-1657] - Linux bin wrapper not needed
* [OP-1663] - Move Qt inside openpilotgcs lib dir to avoid conflict
* [OP-1664] - Github pull request clang warnings
* [OP-1666] - Tidy deb package
* [OP-1667] - Remove firmware files from packages
* [OP-1668] - Add a way to select source for the 'Curve 2' in the custom mixer tab.
* [OP-1674] - Oplink setup : frequency display
** New Feature
* [OP-1503] - Yaffs2 file system library integration to Simposix
* [OP-1637] - AssistedControl
* [OP-1639] - Make non-git source
* [OP-1640] - Write make install rule for Linux
* [OP-1643] - Enable Ground Support in Wizard
* [OP-1651] - Add GCS command line options to log to file
** Task
* [OP-1557] - Update Qwt
* [OP-1558] - Evaluate removal of: ground/openpilotgcs/src/plugins/pathactioneditor/pathactioneditor.qrc
* [OP-1648] - Update PFD after flight mode changes
* [OP-1656] - Upgrade to Qt 5.4.0
--- RELEASE-14.10 ---
This release mainly focuses on flight performance, especially aimed at mini multirotors and adds support for the OpenPilot Platinum GPS (V9).
This version supports the CopterControl, CC3D, Atom and the Revolution Flight controllers as well as the OPLink Modems.
Some key addition in this release:
- A brand new Acro+ flight mode, a Rate mode "on steroids";
- Support for latest OpenPilot Platinum GPS (V9) and its integrated magnetometer;
- Throttle PID Scaling: automatically scale PIDs based on throttle;
- On board Expo support;
- Several additions to the Setup Wizard such as Fixed wing support, GPS selection, TriCopter servo speed selection and ESC calibration;
- First implementation of Cloud Config, Cloud Config in this release is the first version of the future community based distributed system for sharing vehicle settings;
- Redesigned PFD artwork and addition of multifunctional slide out panels;
- Support for additional Flexi-IO serial port for Revolution;
- External (ws281x compatible) status LED support;
- Considerable flight performance improvements.
The full list of features, improvements and bugfixes in this release is accessible here:
http://progress.openpilot.org/browse/OP/fixforversion/10920
NOTE: If you were using OPLink at power levels lower than 100mW, please redo a range test after upgrading to 14.10.
** Improvement
* [OP-838] - Adding servo update rate to vehicle setup wizard for tricopters.
* [OP-1088] - Redesign the OPLink GUI in the GCS
* [OP-1134] - Custom vehicle should show settings from last mixer preset
* [OP-1156] - Unify path followers into a single module with submodules
* [OP-1317] - Improvement of IMU wind estimation
* [OP-1319] - Fix minor spelling mistakes in fw code
* [OP-1324] - Fix build when python isn't python2
* [OP-1338] - copydata.pro uses specific icu so version when it doesn't need to?
* [OP-1370] - Add optional UBX GPS self configuration
* [OP-1379] - Create a notification module that allows for some Naza like led signalling and more
* [OP-1395] - Several enhancements/fixes to flight side log
* [OP-1397] - Add Responsiveness to TxPID
* [OP-1404] - Add support for UBlox PVT sentence
* [OP-1405] - Add support for 25qXXX series of flash memories
* [OP-1406] - Add support for an aux magnetometer
* [OP-1423] - Populate TxPID Min/Max fields with the current values from the Stabilization page
* [OP-1429] - Optimize GPSSatellites UAVO
* [OP-1438] - Change VSI to Arc on the PFD
* [OP-1440] - Timing on WS2812 to support all models
* [OP-1447] - Make it easier to adjust the slider on the Output Calibration Setup Wizard page
* [OP-1451] - Change udev rules from using plugdev group to uaccess/udev-acl
* [OP-1452] - Usability fixes to ComUsbBridge
* [OP-1453] - Check if new version of OP Software suite is available, notify if so
* [OP-1457] - Hide feed forward tab when in config plugin for Fixed wings
* [OP-1458] - Remove delays and other quirks from TX Wizard
* [OP-1462] - Find better default EKF settings
* [OP-1465] - update stm32flash to support new targets
* [OP-1472] - Make connection diagram button more visible
* [OP-1474] - Scaling back PIDs at high / full throttle with Multis.
* [OP-1482] - TPS graph needs labels, also scale should not be -100% to +100%, suggest 50% as max
* [OP-1489] - Hide ILimit stuff
* [OP-1491] - Create H Quad type in artwork and add to wizard
* [OP-1493] - Make the discoveryf4bare target more usable from GCS
* [OP-1504] - Add a SystemSetting field to be used to name the vehicle.
* [OP-1507] - Optimize GPS module cpu utilization
* [OP-1508] - SBus Connection Diagram - Vehicle Setup Wizard
* [OP-1512] - Add ESC calibration to wizard
* [OP-1515] - Gyro Fifo handling for CC3D
* [OP-1516] - Create Acro+
* [OP-1520] - Remove "Attitude" as a selection for Yaw (safety Issue)
* [OP-1521] - Responsiveness scale
* [OP-1524] - Render chars/strings in the Uavobrowser
* [OP-1528] - Enable Telemetry on Flexi-IO (receiver) port on Revo platform
* [OP-1534] - Add expo and acro insanity factor to TxPID
* [OP-1535] - MPU handling optimization
* [OP-1538] - UAVO Browser - embedded descriptions
* [OP-1543] - Make GPS plugin look sexy
* [OP-1545] - Add visual feedback to ESC calibration screen on Wizard
* [OP-1546] - Cloud config uses "none" for the defaults, can this be changed to Generic <airframe type>?
* [OP-1548] - Remove, the Comp + amg and comp+mag+GPS modes
* [OP-1552] - Rename Radio Setup Wizard in tools menu
* [OP-1554] - Allows for enum values in plot showing them as labels
* [OP-1556] - Improve ESC calibration.
* [OP-1559] - GPS setup wizard should not say "Main Port"
* [OP-1566] - Add stop button to ESC calibration in Wizard
* [OP-1571] - Cloud config enhancements.
* [OP-1580] - Upgrade Qwt libs to 6.1.1
* [OP-1582] - Change TX Wizard button to show skip / next on aux channels
* [OP-1588] - Makes sure all Relay tuning is removed, UAVOs still exist for example
* [OP-1589] - Save mixer with cloud config
* [OP-1590] - Copy Bank function for multiple stabilization banks
* [OP-1624] - Make Aux Mag default if selected via Wizard
* [OP-1625] - Satellite dsm2/dsmX channel resolution autodetection.
* [OP-1627] - Clean up PiOS DSM post Matt fix
* [OP-1635] - Remove Quah H frome wizard to avoid confusion with Quad X
** New Feature
* [OP-1222] - Add support for Fixed Wing configuration in Vehicle Setup Wizard
* [OP-1275] - Create a PiOS F0 target
* [OP-1403] - Add generic I2C/SPI HMC5x83 mag driver
* [OP-1434] - Support for GPSV9
* [OP-1476] - Serial bootloader and support tools for F0
* [OP-1477] - V9 firmware
** Task
* [OP-1093] - Investigate Font issues on non-Windows platforms
* [OP-1337] - French translations updates (14.10)
* [OP-1398] - Qt 5.3.1 upgrade
* [OP-1468] - Change default PIDs for Atom
* [OP-1544] - Change defaults for GPSSettings.UbxAutoConfig to "Configure"
* [OP-1632] - Add CloudConfigs to install
** Sub task
* [OP-790] - Add labels to Custom Mode Vehicle type channels
* [OP-1399] - Qt 5.3.1 upgrade (Windows)
* [OP-1400] - Qt 5.3.1 upgrade (Linux)
* [OP-1401] - Qt 5.3.1 upgrade (Mac)
* [OP-1435] - Add Up Time, Arm Status and flight mode to PFD
* [OP-1439] - Add minor vignette / gradient to PFD
* [OP-1525] - GUI for Acro+
* [OP-1577] - Fixed Wing Wizard Images truncated and missing information
* [OP-1592] - "Cloud config" fails on cc3d
* [OP-1605] - Normalize fixed wing mixers and mixing slider jitter while saving
** Bug
* [OP-609] - Input wizard is too sensitive for some people, seems to create bugs
* [OP-868] - Text in Barographs is beyond image in Horizontal, Too tight spacing in Vertical
* [OP-922] - compiling firmware with DEBUG=YES fails in multiple places
* [OP-1077] - GCS corrupts flight log files (*.opl)
* [OP-1140] - Weak Leveling code appears to be wrong
* [OP-1186] - Clean up GCS configuration UI...
* [OP-1305] - Subpar CC3D and REVO performance on Mini H frames
* [OP-1349] - GCS Neutral Spinboxes in Input and Output are incorrectly affected by and affect Min and Max
* [OP-1362] - Translation : 'make ts' errors
* [OP-1422] - Vehicle Setup Wizard (Tricopter) and Vehicle Mixer Settings Frame type dropdown (Tricopter) do not give the same Pitch mixer settings
* [OP-1425] - A small typo
* [OP-1433] - Change the order of the TxPID PID Options
* [OP-1445] - GCS bugs down in RC Input and Manual Calibration
* [OP-1455] - No output from "Test outputs" until sliders are moved
* [OP-1459] - Workaround white-box bug in GCS on OSX
* [OP-1460] - ICU libraries need to be copied, like they used to be.
* [OP-1461] - copyqt logic flawed on linux
* [OP-1463] - New copyqt logic might break if user has alternate OPENPILOT_TOOLS_DIR defined
* [OP-1473] - Incorrect Handling of EOF bytes for Futaba R7008SB
* [OP-1478] - Qt Creator build fails on windows
* [OP-1481] - UAVTalk transacted sends limit the number of waypoints that can sent over a slow link
* [OP-1483] - Switching from ReturnToBase into PathFollower mode doesn't work reliably
* [OP-1484] - Yaw rate Ki slider on basic stabilization page out of range
* [OP-1485] - board target revoproto is broken
* [OP-1488] - Typo in uavobject.java.template
* [OP-1494] - First exit from Stabilization page brings up warning, although no changes made
* [OP-1499] - UBXAutoConfig not Auto Configuring
* [OP-1506] - Wrong display in altitude / speed + refactoring PFD
* [OP-1510] - Don't force operating at 100mW
* [OP-1513] - Filter every temperature measurement used for temperature calibration
* [OP-1517] - Setup Wizard - sets SBus and GPS to main port
* [OP-1522] - Improve Robustness of OPLink radio
* [OP-1526] - Reverse all motors not working?
* [OP-1532] - OPLINKMINI and Revo do not communicate correctly
* [OP-1536] - The Revo ComBridge outputs garbage at the end of transmissions
* [OP-1537] - OPLink unreliable at high data rates
* [OP-1539] - AcroInsanityFactor limit parsing error
* [OP-1540] - Fix GPS v9 reported sha1sum
* [OP-1542] - Welcome Screen does not show latest available Update
* [OP-1549] - Maps no longer working
* [OP-1553] - OPlink does not work as non coordinator
* [OP-1562] - Welcome plugin warnings
* [OP-1563] - GCS crashes when doing a manual TX input calibration
* [OP-1564] - Incorrect display of Thrust mode in PFD Module
* [OP-1565] - Motors will not stop after 2nd time of using set neutral in wizard
* [OP-1567] - Fix bugs in Wizard
* [OP-1568] - Black tooltip over Telemetry monitor
* [OP-1570] - The Vehicle gadget defaults as a quad x with + mixes 100 100 50
* [OP-1572] - Wrong frame type displayed in PFD gadget
* [OP-1573] - Revo disarms in PATHPLANNER flight modes if throttle is low.
* [OP-1574] - Missing ESC throttle range calibration screen when 50Hz rate is selected
* [OP-1584] - High RAM usage on CC
* [OP-1586] - Test outputs can fail to stop motors in some cases
* [OP-1601] - Still not enough ram on CC for gps to be usable
* [OP-1603] - Fixed Wing (elevon) : Wizard and Config mixer differs
* [OP-1604] - Radio wizard crashes
* [OP-1618] - High CPU load caused by radio module driver
* [OP-1633] - Wizard enables serial ports on Revo
* [OP-1634] - Cloudconfigs use wrong path in install
--- RELEASE-14.06.01 ---
This is the first maintenance release for 14.06.
This mainly fixes a bug causing flips when switching to Weaklevel flight mode.
The full list of features, improvements and bugfixes in this release is accessible here:
http://progress.openpilot.org/issues/?filter=11660
**Bugs
* [OP-1241] - TxPID Does not work for Bank 3 PID settings
* [OP-1432] - Hexa config : "Reverse all motors" do not reflect current config after reload
* [OP-1454] - weak leveling code buggy, causes NAN and crash!
** New Feature & Improvements
* [OP-1450] - GCS fonts are blurry on OSX and retina displays
--- RELEASE-14.06 --- Peanuts Schnapps ---
This is the Mid 2014 release.
This version supports the CopterControl, CC3D, Atom and the Revolution Flight controllers as well as the OPLink Modems.
This release includes many additions, improvements and fixes, it is the result of many thousands of hours of development and testing.
Some key additions in this release:
- Many additions and changes aimed at gps/navigation functionality for the Revolution platform including GPS assisted flight modes: Return To Base, Position Hold, AutoCruise and Position Vario(LOS, FPV and NSEW).
- Stabilization refactoring and enhancements for even better flight performance.
- Completely new sensor calibration routines and greatly enhanced GUI.
- Additional 3rd Party Hardware support, notably the MS4525DO based airspeed sensors and WS281x LED drivers.
- Performance improvements in both embedded firmware and GCS.
The full list of features, improvements and bugfixes in this release is accessible here:
http://progress.openpilot.org/issues/?filter=11460
** New Feature & Improvements
* [OP-943] - Start using F4's Core Coupled RAM for more than just the IRQ handler stack
* [OP-974] - Make Bootloader Version available while flight software is running
* [OP-975] - Reconsider the calibration process
* [OP-1063] - Multirotor Configuration
* [OP-1068] - Add support for magnetometer calibration matrix in place of scaling parameters
* [OP-1149] - handle thermal bias calculation/calibration to gyro and accel
* [OP-1150] - Create UI to allow users to perform board thermal calibration
* [OP-1159] - Remove "Rev" checkboxes on input tab for channels on which it doesn't have an affect
* [OP-1161] - Add Alarm for Magnetometer if disturbed or uncalibrated
* [OP-1174] - Beautify Uploader gadget popups
* [OP-1194] - Scope gadget - plot and legend visibility state should be persisted between runs
* [OP-1198] - Allow GCS gadgets to save/restore individual state
* [OP-1216] - Refactor Flight Control Modules
* [OP-1230] - automatically load the correct firmware file when GCS is running in a development environment
* [OP-1233] - Add make options to skip qmake and build a specific GCS directory
* [OP-1245] - Add GUI to control if, what, when and how to do flight side logging.
* [OP-1247] - Remove Noise calibration from Revo calibration config widget
* [OP-1250] - Add GPS Protocol configuration in the Hardware configuration panel
* [OP-1258] - Update GCC ARM Embedded to 4.8-2014-q1
* [OP-1259] - Cruise Control tweaks
* [OP-1260] - Rattitude tweaks
* [OP-1273] - Implementation of the PixHawk airspeed sensor based on the MS4525DO
* [OP-1282] - Include I2C Alarm into Eagletree speed sensor module
* [OP-1287] - GPS assisted flight for Revo
* [OP-1299] - Autodetect number of cells in Battery module
* [OP-1302] - Improve on board led functionality
* [OP-1303] - Add PathPlan Alarm in System Health
* [OP-1307] - Create a bare DiscoveryF4 target for debugging and development purposes
* [OP-1308] - Set the same logic to CRITICAL Alarm and same logic to ERROR Alarm
* [OP-1312] - Implement a PIOS WS281x driver
* [OP-1335] - ConfigTaskWidget - Add support to bind GComboBox to integer property
* [OP-1339] - System Health panel improvement
* [OP-1378] - Check Limits for flight modes
* [OP-1342] - PFD widget emits lots of warning
* [OP-1350] - TakeOff location handling to be used with RTB
* [OP-1358] - Split board rotation into user set configuration and calibrated offset
* [OP-1365] - Add instrumentation functions for flight code
* [OP-1374] - Automatically enable the right PathFollower
* [OP-1390] - OpenGL support for older Graphics Cards
* [OP-1413] - Disable Land flight mode
** Bug
* [OP-792] - 'Autotune' still showing up in flight mode settings in GCS
* [OP-1026] - Provide some standard method of calibrating CPU speed and load measurement for boards
* [OP-1033] - Data transfer errors on USB HID on F1 devices
* [OP-1043] - Ground OPLinkMini refuses to connect to one Revo unless first connected to another Revo
* [OP-1056] - GPS does not set home location when erased after lock has been established
* [OP-1080] - Unreliable detection of board through OPLink
* [OP-1100] - gcs plist for mac shows wrong associated filetypes, leftover from qtcreator
* [OP-1131] - Firmware mismatch check is not done if Uploader gadget is not active
* [OP-1172] - Some fonts are not defined in config files
* [OP-1196] - Board rotation in GCS not shown correctly upon connection but correctly saved in memory
* [OP-1212] - Fix Priority queue handling in telemetry
* [OP-1226] - screen problems
* [OP-1227] - High CPU load in ratitude mode on CopterControl
* [OP-1232] - Setting high telemetry rates for periodic uavobject triggers eventsystem warning.
* [OP-1235] - Some fixes for altitude estimation
* [OP-1237] - Blank/Black Buttons on Vehicle Configuration Multirotor Throttle Curve
* [OP-1241] - TxPID Does not work for Bank 3 PID settings
* [OP-1243] - OPMap widget context menu duplicating some menu separators each time its opened
* [OP-1252] - Update GCS to qt 5.2.1
* [OP-1266] - Gyro and accel thermal compensation is not applied if one or more coefficients have negative value
* [OP-1267] - Incorrect UAV position on GCS OPMap after homeLocation modification
* [OP-1272] - Unable to debug in SWD mode a revo board
* [OP-1283] - SystemHealthGadgetWidget::updateAlarms misinterprets coordinates in SVG file
* [OP-1284] - RTB flies into ground if base is high
* [OP-1285] - Erase Settings ToolTip is wrong
* [OP-1288] - GPS PositionHold immediately flies several meters away if Home is not close
* [OP-1291] - fix matlab import after UAVTalk changes
* [OP-1294] - Fix stack sizes for CopterControl
* [OP-1295] - Autoupdate not working
* [OP-1296] - Altitude Hold causes copter to ascent at full throttle when far from home location
* [OP-1297] - OPMap fails to read in saved waypoints correctly
* [OP-1300] - SystemHealth gadget does not show "Configuration Alarm"
* [OP-1301] - Hardware settings can't be saved with CC/CC3D
* [OP-1304] - Revo stack alarm
* [OP-1314] - Fix Airspeed stack size
* [OP-1315] - Unable to arm UAV when AirspeedSensorType is set to GroundspeedBaseWindEstimation
* [OP-1323] - GCS font fixes
* [OP-1325] - fix event system warnings to be errors
* [OP-1326] - set AIrspeedSensor default back to "None"
* [OP-1327] - SystemAlarms must be non-acked
* [OP-1329] - Various fixes to airspeed module
* [OP-1330] - Cannot set homelocation.set=false when gps reception is optimal
* [OP-1331] - Input and Output Channel Configuration alignments issues
* [OP-1332] - PiOS alarms does not reset alarm state on timer overflow
* [OP-1333] - Output Channel Configuration alignments issues
* [OP-1340] - Auto-update greyed out - not available
* [OP-1343] - GCS Configuration - Input Channel ResponseTime not saved
* [OP-1346] - Input Channel Response Time mismatch between GCS config screen and UAVObject
* [OP-1347] - Flight logs settings - UI / segfault
* [OP-1348] - Config Gadget flashes next panel when connecting/disconnecting board
* [OP-1351] - GCS Calibration UI polishing
* [OP-1352] - Headwind-improvements for FixedWingPathFollower
* [OP-1353] - HITL Flightgear fails to set Position and velocity correctly
* [OP-1354] - Current and voltage not shown in PFD
* [OP-1355] - magnetometer calibration and board rotation don't play along
* [OP-1363] - sanitychecks MUST check if magnetometers and GPS are enabled for any pathfollower modes (outdoor mode selected)
* [OP-1371] - sanitychecks overzealous: hitl/sitl broken
* [OP-1375] - Update Mag Ki and Kp default settings
* [OP-1376] - Calibration results not saved to SD
* [OP-1377] - Calibration config panel has Apply button even when not in Expert mode
* [OP-1383] - GCS crashes when connected via serial port
* [OP-1384] - Revo Board Rotation data is cleared to zero by other calibration steps
* [OP-1389] - GCS Crashes exiting Flight side log window
* [OP-1391] - System allows arming if current flight mode uses Thrust Control = AH or AV
* [OP-1393] - SerialPlugin destructor generates valgrind error
* [OP-1394] - Flight display widget - telemetry data does not zero on disconnection
* [OP-1408] - Board rotation is not always saved during Revo calibration
* [OP-1412] - INS13Outdoor Yaw Gyro drift
* [OP-1415] - Repeated names in CREDITS.txt
* [OP-1419] - GCS does not set Z magnetometer scale correctly on mag calibration
* [OP-1421] - Cruise Control xml defaultvalue incorrect
** Tasks
* [OP-1274] - Update FreeRTOS to 8.0
* [OP-1337] - French translations updates (14.04/05)
* [OP-1254] - Update to QT5.2.1 for Linux x86/64
* [OP-1263] - Move SDL out of Qt install
* [OP-1309] - Stabilization refactoring
--- RELEASE-14.01 --- Cruising Ratt ---
This is the first 2014 software release.
This version still supports the CopterControl and CC3D.
It includes some major "under the hood" changes like migration
to Qt5.1 and QtQuick2 widgets, an overhaul of UAVTalk to improve
Telemetry and OPLink reliability.
Some additions in this release:
- "Rattitude" flight mode;
- Altitude Hold Reimplementation;
- Multiple PID banks;
- "Cruise Control"
the full list of features, improvements and bufixes shipping
in this release is accessible here:
http://progress.openpilot.org/issues/?filter=11260
** Improvement
* [OP-771] - Change Wizard wording for better usability
* [OP-791] - Integrate About Authors, OpenPilot GCS, Plugins dialogs into a single dialog window
* [OP-803] - Gadgets get their configuration set twice when restoring workspaces during GCS startup
* [OP-835] - Upgrade GCS to use Qt 5.1.0
* [OP-883] - Make system and flight targets cleanup, pass 01
* [OP-913] - Poor UAVObject data structure alignment on flight side causes performance degradation
* [OP-951] - Add -Wshadow to flight CFLAGS and fix compilation breakage that results
* [OP-966] - Scope Plugin Cleanup
* [OP-984] - Provide multi PID banks, these should be assignable per flight mode.
* [OP-996] - Add GCS option to remember the last selected workspace
* [OP-1022] - Additional improvements for altitude hold
* [OP-1036] - Improvements to Fixed Wing PathFollower and Nav
* [OP-1059] - Typo (2x) in OpenPilot Setup Wizard - Output Calibration Window
* [OP-1063] - Multirotor Configuration
* [OP-1071] - Make map "emergency" lines less strong and dashed
* [OP-1079] - Update to FreeRTOS v7.5.2
* [OP-1082] - Add a ticker on the Welcome page showing Jira activity alongside the 'Project News'
* [OP-1083] - Fix minor English spelling errors in stabilization tooltips
* [OP-1085] - Upgrade GCS to use Qt 5.1.1
* [OP-1094] - Turn on Progress for large SDK downloads / remove for MD5 files
* [OP-1104] - Create BL version 6 to support larger firmware
* [OP-1105] - If firmware .info blob is missing, test string is too long
* [OP-1107] - Convert About dialog to QTQuick 2.0 and cleanup code.
* [OP-1110] - Move Welcome screen to QtQuick 2
* [OP-1111] - Move About to QtQuick2
* [OP-1112] - Update contributors in GCS
* [OP-1113] - Convert new PFD design to QtQuik2
* [OP-1117] - Implement Horizon mode
* [OP-1120] - Waypoint upload to board should be transacted
* [OP-1133] - UAVTalk - expose send/request all instances of multi instance uav objects + related uavtalk fixes
* [OP-1137] - Make Configuration Checkbox checked by default during uninstall
* [OP-1141] - Add a further bias correction to barometer to better handle thermal variations
* [OP-1143] - Missing Linux udev rules for Revolution boards
* [OP-1153] - Provide a mean to instrument SystemMod stack utilization
* [OP-1154] - Config Option to Automatically Increase Copter Throttle per 1/cos(bank_angle)
* [OP-1158] - Add flight plan consistency checks
* [OP-1160] - Some dev Env improvements, git hooks for messages, make prepare etc.
** Task
* [OP-775] - Add ARM DSP library to OP codebase
* [OP-813] - Manage merge of translation work to French
* [OP-839] - Disable pyMyte dependency until really used
* [OP-901] - Update STM32 StdPeriphLib to current
* [OP-1087] - Update Qt used from Makefile to 5.1.1 for Windows and Mac
* [OP-1109] - Created share Qt5 QtQuick2 port branch
* [OP-1115] - Remove old artwork from the Artwork folder in Git
* [OP-1119] - Write GCS plugin to access and display on board logs through uavtalk and export .opl files from logged uavobjects
* [OP-1058] - UAVO:Implement a structured named accessors for multielement fields (Flight side)
** Bug
* [OP-844] - Fix header comments in altitudehold.c
* [OP-845] - Fix reading serial number from USB device on mac platform
* [OP-846] - make qt_sdk_install fails
* [OP-865] - PWM output 6 does not work on RM
* [OP-887] - Provide some standard method of calibrating CPU speed and load measurement for boards
* [OP-924] - PPM output does not have failsafe
* [OP-934] - Incorrect timeout handling in rfm22b receiver
* [OP-971] - Add UI to set AccellTau with revo board
* [OP-1004] - UAVObjectBrowser, buttons don't work when scientific display is turned on
* [OP-1014] - Com port connections are not working on OPLink
* [OP-1018] - Zero point initialization in ETASv3 Airspeed sensor buggy
* [OP-1027] - Segfault in UAVObjectBrowser when "Request"ing a UAVObjectCategory
* [OP-1042] - Revo firmware version isn't read correctly through OPLink
* [OP-1046] - Waypoint upload incomplete, no visual confirmation of failed uploads in uavobjectbrowser and waypoint editor
* [OP-1048] - Attitude is not working with AccelTau > 0
* [OP-1049] - CC3D attitude estimation failure after multiple settings changes and reboots
* [OP-1067] - Invalid value for "LinkState"
* [OP-1076] - CF Attitude filter in next randomly re-initializes on arming.
* [OP-1078] - GCS segfaults if you close it after playing a log file
* [OP-1080] - Unreliable detection of board through OPLink
* [OP-1095] - GCS crashing on macosx 10.9 upon connection of oplink mini
* [OP-1098] - CDC driver fails installation in Windows 8 or 8.1
* [OP-1099] - Hidden icons in Configuration tab
* [OP-1101] - Tools.mk has a few tabs and they need to be converted to spaces
* [OP-1102] - OP GCS registers some file types is should not
* [OP-1103] - GCS can not be compiled on OSX 10.8 after update to Qt5.1.1
* [OP-1108] - Minor bugs found while reading the code
* [OP-1114] - QGLWidget prohibits QListWidgetItem, set AA_DontCreateNativeWidgetSiblings as work around
* [OP-1118] - QComboBox in UAVObjectBrowser does not stay in focus on Mac OSX
* [OP-1121] - GCS will not exit if the Waypoint editor/PathPlanner dialog is open
* [OP-1123] - GCS assertion failure when loading a waypoint file
* [OP-1125] - UAVTalk - acking/nacking multi instance uavobjects is broken (when sending individual instances)
* [OP-1132] - LIBEAY32.dll missing from installer
* [OP-1139] - Add higher order correction to MS5611 driver for low and very low temperature compensation
* [OP-1142] - No yaw in Horizon mode
* [OP-1145] - OPLM to GCS link not reliable
* [OP-1148] - Futaba R7008SB S.Bus protocol not supported
* [OP-1151] - PFD display - inverted flight
* [OP-1152] - Check Stack usage for CopterControl & CC3D
* [OP-1155] - Fix OSX Packaging for GCS
* [OP-1157] - sin_lookup_deg() returns garbage for negative angles
* [OP-1166] - GCS misses yaw neutral setting on sync from initial connection
* [OP-1167] - New flight mode switch position UAVO to work better with SITL, HITL
* [OP-1168] - GCS Reload Board Data button doesn't work
* [OP-1169] - GCS UAVO object titles off by one
* [OP-1176] - Cruise Control checkboxes use wrong Default button
* [OP-1177] - AltHold - Need a setting to allow disabling of bank angle throttle compensation in AH
* [OP-1178] - After re-factoring of ConfigTaskWidget code the OPLink config page does not work reliably.
* [OP-1179] - About box not working in Linux64 build (but probably the same is for Linux32)
* [OP-1180] - GCS AltHold Tab - Reload button and update in real time
* [OP-1181] - on radio configuration the pitch slider has maxed out on its own three times randomly
* [OP-1182] - Telemetry monitor widget is too small on Mac
* [OP-1183] - UAVBrowser displays hex string as decimal
* [OP-1184] - Scope gadget - Stack monitor configurations need a cleanup
* [OP-1188] - Optimize Stabilization Module stack size usage
* [OP-1191] - Revo OPLink bug in GCS
* [OP-1192] - Even though Throttle is off there is motor movement in some situations.
* [OP-1211] - dT calculation in Stabilization and other modules unsafe
* [OP-1218] - PIOS_COM is not thread safe
* [OP-1228] - GCS Quits unexpectedly
--- RELEASE-13.06.04 ---
This maintenance release includes the following fixes missing in (previously not released to public) RELEASE-13.06.03.
- Fixed issues with Google Maps;
- Includes new signed version of CDC drivers for Windows platforms;
JIRA issues addressed in this maintenance release:
OP-1044, OP-1070, OP-1072
Use the following link for a comprehensive list of issues addressed by this release
http://progress.openpilot.org/issues/?filter=11060
--- RELEASE-13.06.03 ---
This maintenance release addresses the following issues:
- Fixed CC3D attitude estimation failure after multiple settings changes and reboots.
- Fixed OPLink crashes when erasing settings
JIRA issues addressed in this maintenance release:
OP-1049, OP-1050
--- RELEASE-13.06.02 ---
Refactoring of OPLink radio driver. Auto-configuration was removed, and a
one-way link was added, including a ppm-only mode that is intended to be used
when only a PPM link is desired. PPM-only mode configures the modem as a
one-way link running at 9600 bps (air datarate) and only sends PPM packets.
--- RELEASE-13.06.01 --- Italian Stallion Release ---
It applies the following changes to previously not released to public RELEASE-13.06
- Temporary disabled AltitudeHold and AltitudeVario flight modes. They were not
officially supported. But since people expected well-known production quality
behavior, it is better to make them final, then reenable
- Fix windows hid connection failure if board was already connected and gcs started;
- Fixed a bug that lead to disabled controls with some settings combination in CC/CC3D hardware page
- Fixed a bug that prevent to correct saving stabilization settings for CC/CC3D
- Fixes Uploader GUI and automatically close AutoUpdate panel after 7s
JIRA issues addressed in this release:
OP-1028 OP-1020 OP-1024
--- RELEASE-13.06 ---
This is the first official OpenPilot Revolution software release. This version
also supports the CopterControl, CC3D, OPLinkMini and the upcoming OP OSD.
There a number of significant backend changes in this version compared to
previous software releases: from new toolchains and build system to a source
code reformatting that is inline with our project style guidelines.
The goal of this release is to provide CC3D-style features for the new
Revolution platform (using the Revo's internal modem and external OPLinkMini
board). Advanced features such as Altitude Hold, Position Hold, Guidance,
Return to Home, and AutoLanding are still in development and will be available
in future releases. The availability of those features will depend on how many
people are able to contribute with code, testing and documentation.
Remember that the first Revo hardware batch was intended for developers/
bleeding-edge testers, not end users who want a 100% final platform.
- New bootloaders are REQUIRED for this release to support new features such
as erase settings and others. As always, bootloaders can be updated without
any special programmer hardware using the bootloader updater firmware files.
- F1 boards (CC, CC3D, OPLinkMini) require bootloader version 4 or higher.
- F4 boards (Revolution, OSD prototype) require bootloader version 5 or higher.
- Check the wiki for details of how to update them:
http://wiki.openpilot.org/display/BUILDS/Bootloader+update
Please remember to take a moment to view these important tutorials:
http://wiki.openpilot.org/display/Doc/OpenPilot+Tutorials
What's New / Release Notes
--------------------------
NEW:
- Firmware folders removed.
The firmware files folder has been removed in this release. These files
are now integrated into the GCS so they are always up to date and there is
less risk of a firmware mismatch. To update your firmware you must use
either Vehicle Setup Wizard (big green button at the top right on the
Welcome GCS tab) or the new Auto-Update button on the GCS Firmware tab.
- Responsiveness sliders.
To simplify tuning, we have introduced a new Responsiveness slider that
will allow you to modify stick response. For best results, you should
still tune your system with PIDs as tight as possible for better
stabilisation. This will result in better stabilisation, and at the
same time soft or sharp response according to your preferences.
- Auto-Update firmware.
This feature simplifies all OpenPilot board firmware updates. Now all
you have to do is click "Auto-update" on the Firmware tab and follow the
instructions to reflash your OpenPilot board. This is essentially the
same as Rescue but uses the embedded firmware images so there is no need
to browse for them anymore.
- Erase Settings Option.
We previously had a hacky way to delete bad or incompatible settings from
our OpenPilot boards. This old special firmware that did this is now
deprecated and the functionality is now integrated into the latest
bootloaders and firmwares.
To erase settings enter DFU (boot) mode (using Halt or Rescue function)
and click the "Erase settings" button on the Firmware tab and follow the
instructions. This will NOT work with an older bootloader and the "Erase
settings" button will be disabled if an out of date bootloader is detected.
- Language defaults.
GCS now uses the system default language (only French and English are
available currently, please contribute translations). You can change the
language in the GCS Options at any time.
- CDC driver install option (Windows only).
This is an optional USB virtual serial port that is useful, for example,
for updating your GPS configuration using the U-Blox u-Center software.
It is NOT required for normal configuration of OpenPilot boards. If it is
not installed, virtual serial port features will not be available. This
driver is not signed by Microsoft, but in fact it uses serial port drivers
from Windows and only the driver information INF file is supplied by
OpenPilot.
- Lots of help tooltips were added to the GCS. Hovering your mouse over an
option in the GCS will show them, please review for help during tuning/
setting up.
- A large amount of general improvements, code clean ups and minor bugs
resolved.
KNOWN ISSUES:
- On Linux you should remove the OpenPilot package if it was previously
installed, then install this new one. This is a known issue and likely
be fixed later.
- Due to changes in USB descriptors to support new features, USB drivers
on Windows must be updated. If after using Rescue or Wizard or Auto-Update
button the GCS cannot connect to the board, you may be experiencing this
USB issue. To resolve it you should remove the old drivers (ones with
yellow exclamation mark) and allow Windows to find them again.
Here is how to do it:
Windows XP:
- Right click on "My Computer" on your desktop and select "Properties".
- Select the "Hardware" tab.
- Select the "Device Manager".
- Scroll down the list until you see the "Universal Serial Bus Controllers"
selection.
- Click it to expand the list of USB drivers. Right-click on the driver(s)
you wish to uninstall and select "Uninstall".
Windows 7/Vista:
- Right click on "My Computer" on your desktop and select "Properties".
- Select "Device Manager" in the upper left-hand corner of the window.
- Scroll down the list until you see the "Universal Serial Bus Controllers"
selection.
- Click it to expand the list of USB drivers. Right-click on the driver(s)
you wish to uninstall and select "Uninstall".
Then disconnect the board from USB, wait few seconds and re-connect it to
your computer. Windows should find new drivers and install them properly.
- If GCS crashes when switching to the Flight Data tab, it usually means
your PC needs newer video drivers. That tab contains a ModelView widget
which uses OpenGL. It is known to crash on some graphics cards with old
and buggy drivers.
- Sensor calibration is not final. It will be reworked completely to
increase its accuracy and make it easier to use.
- Until the calibration is reworked, default attitude estimation algorithm
used by Revo is a complimentary filter with magnetometers disabled. Hence
Revo does not use them yet to correct yaw drift. Magnetometers can be
enabled, but you should properly calibrate them first. That's the reason
why they are disabled by default.
- AltitudeHold/Vario modes are enabled but not officially supported. Do
not expect it to work perfectly and be considered production quality.
You may play with it and report your issues and suggestions at your own
risk. If you are not using a case for your Revo, we strongly recommend
covering the barometer sensor with some foam to shield the sensor from
wind and light.
- Note that throttle stick in AltitudeVario mode is used to control vertical
velocity, sometimes called vario altitude in other platforms, centre stick
means hold altitude and there is a dead band around centre stick.
- There are currently no configuration options for the Radio module in
the Revolution except for Radio enable/disable and output power. This is
intentional because all configuration should be done using its paired
ground OPLink coordinator.
How to configure the Revolution to OPLinkMini radio link:
- Make sure you have the newest bootloaders and matching firmwares
between the Revolution, GCS and OPLink.
- Enable the radio in the Revolution, click save and disconnect the board
from USB.
- Power it from external supply to continue.
- Then connect the OPLink board to USB and scroll down in the GCS config
widget to find OPLink icon at the end of list. This icon is only
available when an OPLink is detected.
- To pair the two radios, select the Revolution side radio address in the
list of found boards, select it, click Add to add to the list of paired
radios and click Save. After unplugging the board from the USB and
plugging back your OPLink it should show "Connected", and you can
continue with the configuration.
- Do not set the Revolution modem or OPLinkMini output power to high values
without antenna connected, this can damage the hardware.
JIRA issues addressed in this release:
Due to major rework of all code and integration of Revo code into mainline
(next) it is almost impossible to list all corresponding JIRA issues for the
list above. Some of them can be found using this link:
http://progress.openpilot.org/issues/?filter=10860
OP-678, OP-682, OP-693, OP-719, OP-726, OP-727, OP-747, OP-761, OP-769,
OP-770, OP-772, OP-781, OP-784, OP-792, OP-804, OP-807, OP-812, OP-816,
OP-817, OP-820, OP-821, OP-834, OP-843, OP-846, OP-854, OP-855, OP-856,
OP-861, OP-864, OP-867, OP-871, OP-873, OP-874, OP-875, OP-879, OP-885,
OP-886, OP-888, OP-889, OP-890, OP-891, OP-892, OP-893, OP-894, OP-895,
OP-896, OP-897, OP-898, OP-899, OP-900, OP-903, OP-905, OP-906, OP-907,
OP-910, OP-912, OP-917, OP-920, OP-925, OP-926, OP-928, OP-935, OP-936,
OP-939, OP-952, OP-955, OP-957, OP-958, OP-965, OP-968, OP-969, OP-970,
OP-977, OP-979, OP-980, OP-981, OP-982, OP-983, OP-988, OP-989, OP-990,
OP-991, OP-993, OP-997, OP-998, OP-999, OP-1000, OP-1002, OP-1005, OP-1007,
OP-1008, OP-1009, OP-1010, OP-1011, OP-1012, OP-1013, OP-1015, OP-1016, OP-1021
Short summary of changes. For a complete list see the git log.
Flight code changes:
- initial version of Revo code;
- initial version of OPLinkMini code;
- CopterControl/CC3D code reworked to reuse parts of Revo code;
- switched to new ARM-supported GCC 4.7 toolchain with hardware floating point support;
- major code cleanup and use of compiler warning flags to early catch errors;
- major directory and Makefiles reorganisation and cleanup;
- all source code fixed to use float variables instead of doubles (to use hardware FPU);
- added multi-binding support for OPLinkMini;
- added frequency hopping for Revo and OPLinkMini;
- added auto-configuration for OPLinkMini remote modem / Revo;
- replaced entire flash generation code;
- new U-Blox GPS binary protocol parser;
- added STM32 DSP library;
- updated STM32 CMSIS library;
- updated STM32 USB OTG driver;
- updated STM32 F1 StdPeriph driver library;
- updated STM32 F4 StdPeriph driver library;
- updated FreeRTOS (real-time operating system used by the flight code to run many tasks);
- PyMite moved to a library;
- fixed nasty bug in PyMite Makefile, single file was rebuilt 5 times fo no reason;
- added configurable accel/gyro rates;
- added visualisation of errors in bootloader updater;
- added numerous sanity checks to the flight code to prevent unsafe arming;
- new flash file system, much faster and higly optimised;
- Revo data flash is splitted into two partitions, one for settings, another for user data (logs, etc);
- OPLinkMini now stores settings in the MCU flash using FlashFS too;
- a catalog of known flash types is used to support different flash types by the same firmware;
- fixed broken overo submodule remote repository link;
- fixed DSMX protocol error with some Tx/Rx combintions;
- added new pios_*.h headers to support commonly used constants, functions and defines;
- numerous fixes for data alignment and memory allocation strategy;
- new bootloaders to support more features (for example, board settings erase);
- added new feature to erase settings without special firmware;
- removed CC/CC3D setting erase firmware (now not necessary due to new erase feature);
- introduced new delayed callback scheduler to run modules from a single task;
- many changes to AeroSim-RC simulator interface;
- fixed broken debug pins API;
- fixed few bugs in the EKF code;
- introduced bootloader updater for F4 boards (including Revo and OSD);
- some changes in RAM and flash memory partitioning to better utilize resources;
- changes in bootloader to allow remote reboot via serial port or radio modem;
- the EKF "Huge Formula" is replaced by optimised set of of loops to make it editable;
- Cyr's attitude patch is ported from CC3D to Revo;
- added magnetometer options (mags are disabled by default for Revo complimenary filter);
- advance camera stabilisation is now officially released;
- Revo alarm led now distinguish between Critical(lit led), Error(blink fast), Warning(blink slowly) Alarm condition
- Revo alarm led flash fast(like in Error Alarm) during calibration using complementary attitude estimation.
- Redo gyro bias zero after calibration parameters changes
- Do not raise GPS alarm if a gps port is not configured.
- fixed numerous internal firmware bugs (too many to list here).
GCS code changes:
- nice loading splash screen;
- now GCS uses system language by default if translation is available, English otherwise;
- French translation officially added. Please help with other languages;
- fixed some crashes of uploader gadget;
- fixed double config read on restore;
- improvements in GCS options dialog handling;
- optimised option dialog creating;
- added UI tooltips for many options;
- removed unused yet options from configuration UI;
- removed GCS config dialog on the first run, one default is used now if missing;
- added Revo configuration page, similar to CC/CC3D one;
- added OPLinkMini configuration page;
- hardware options are now dynamically enabled/disabled to allow supported configurations only;
- new artwork for all boards everywhere;
- optimised some 3D models;
- new About dialog showing version info and contributors list;
- fixed badly broken HiTL options dialog;
- fixed compilation problem on OSX, now GCS should be compatible with OSX 10.5+;
- major vehicle config cleanup with lazy creation (speeds up GCS start);
- UI config pages improvements (responsiveness, etc)
- new auto-update feature added, *.opfw firmware files removed from distributables;
- anti-aliased scope plugin;
- numerous code fixes and cleanups (too many to list here);
- USB HID code is replaced by new cross-platform hidapi library to fix old Linux/OSX problems.
- Adds GUI to set Altitude Hold filter parameters.
- Adds configurable units for velocity/speed and altitude in QML PFD. Units are configured in settings panel.
- Reduces precision of the PDOP value in the PFD display to 1 decimal.
- Remove deprecated powerlog
Common parts:
- added simple toolchain install make targets;
- added self-hosted toolchains to ensure that they're always available;
- added support for globally istalled tools used by many working copies;
- added Windows bootstrap script to pull all other build tools;
- added unit testing framework, also supported by Bamboo CI server and agents;
- added code style formatting make targets, easy to use by developers;
- added doxygen make targets. The documentation still must be completely revised, though;
- enforced global line ending policy, source files are updated accordingly;
- reworked packaging to provide correct dependencies and safe multi-threaded builds;
- multiply renames of board names and directories, now we have correct names;
- fixed dependencies in Makefiles, now 'make -j' works reliably;
- CLEAN_BUILD make option is deprecated, use 'package' or 'clean_package' instead;
- simposix elf is now included into linux distribution and can be run with default GCS settings;
- revised 'make help' message;
- updated Windows driver to support Revolution and use correct board names.
Android GCS:
- old and buggy code was removed;
- full rewrite has been started.
Infrastructure:
- Bamboo continuous integration server is actively used;
- around 10 build agents running 4 different operating systems are set up;
- every push to any branch is now build-tested, and unit tests run are performed;
2012-11-17
Advanced camera stabilization features.
They include optional manual control input filtering (moved from camera stabilization to manual
control input and now available also for main controls), optional airframe attitude filtering
used by camera stabilization, and optional camera actuator feed forward to improve gimbal response.
--- RELEASE-12.10.2 --- Mayan Apocalypse Release ---
List of issues resolved in this maintenance release:
http://progress.openpilot.org/issues/?filter=10361
OP-459, OP-545, OP-674, OP-679, OP-685, OP-686, OP-687, OP-690, OP-691,
OP-702, OP-703, OP-714, OP-715, OP-716, OP-721, OP-728, OP-746, OP-748,
OP-749, OP-750, OP-758, OP-759, OP-760
Here is a list of some known unresolved issues. If an issue has JIRA ID [OP-XXX],
you may track it using the following URL: http://bugs.openpilot.org/browse/OP-XXX
+ Only French translation is updated, use English for other locales or help with translations.
+ Radio Wizard confused by a reversed throttle, fix it on your transmitter before starting wizard.
+ Radio Wizard Throttle display does not show full range properly.
+ [Windows 8] USB Driver is broken.
+ Firmware Update Instructions on Firmware Tab not entirely accurate for all upgrade paths.
+ Tricopter's using Vehicle Wizard need to check servo does not need reversed manually.
+ XAircraft ESCs uses non-standard PPM range which may cause issues with Vehicle Wizard.
+ Spectrum Satellite Receivers setup in Radio Wizard may have wrong protocol set.
+ Old Intel 965 have an OpenGL bug that turns the QML PFD black and while.
+ [OP-732] Import UAV Settings for inactive modules crashes the running firmware (board restarts).