🤗 Please consider subscribing to my YouTube channel Your subscription goes a long way in backing my work. if you feel more generous, you can buy me a coffee

CapiBridge is an open-source one-way gateway for low-power devices. It supports various communication technologies including LoRa, ESP-NOW, and WiFi. The gateway receives JSON strings from LoRa and ESP-NOW DIY devices and publishes them to an MQTT server. It automatically separates the JSON string into dynamic MQTT topics based on keys within the JSON, such as "b" for battery or "m" for motion, making it highly compatible with Home Assistant. This gateway simplifies adding new DIY nodes/sensors to your smart home by standardizing the communication protocol across all your DIY projects, focusing on simplicity and unified protocol handling.

---

🛒 Where to buy http://www.PricelessToolkit.com

🚀 Sensors that work out of the box with CapiBridge.

• Mailbox Guard LoRa MailBox sensor
• SOILSENS-V5W Soil moisture sensor

---

Specifications

• 1x LoRa Module 868 or 433MHz
• 2x ESP32-C3
• ESP1 Free GPIOs
  • IO7, IO10
• ESP2 Free GPIOs
  • IO10, IO3, IO1, IO0, IO4, IO5, IO6, IO7
• Power Pins 5V, 3.3V, GND
• USB-C with auto reset
• UART switch for selecting ( ESP1 | ESP2 )
• Buttons for flashing and reset
• Debug LEDs
  • USB - TX, RX
  • ESP1 to ESP2 - TX, RX
  • One LED for LoRa
  • One LED for ESP-NOW

Important

A high-quality phone charger should be used to ensure a stable 5V power supply.

---

📣 Updates, Bugfixes, and Breaking Changes

• 28.07.2024 - Binary sensors topics and Motion sensor autodiscovery.
• 15.06.2024 - Publishing battery in percent.

Note

If you're ready to contribute to the project, your support would be greatly appreciated. Due to time constraints, I may not be able to quickly verify new "features" or completely new "code" functionality, so please create a new code/script in the new folder.

---

Do you want to assemble it yourself?

This project is open-source, allowing you to assemble CapiBridge on your own. To simplify this process, I've provided an "Interactive HTML Boom File" located in the PCB folder. This interactive file helps you identify where to solder each component and polarity, reducing the chances of errors to a minimum. But if you don't feel confident in assembling it yourself, you can always opt to purchase a pre-assembled board from my Shop https://www.pricelesstoolkit.com

Schematic

View schematic. Click here

---

Links for antennas and cables.

• 2.4Ghz Antenna + Cable https://s.click.aliexpress.com/e/_DE0sJ7N
• Cable UFL to SMA https://s.click.aliexpress.com/e/_Dnee0tV
• Antenna 433 MHz SMA male https://s.click.aliexpress.com/e/_Dm2X9vv
• Antenna 868 MHz SMA male https://s.click.aliexpress.com/e/_Dczm4y7

---

Before you start

Warning

🔥Connect all antennas first to prevent damage to the transmitter.🔥

Important

If you're new to Arduino-related matters, please refrain from asking basic questions like "how to install Arduino IDE". There are already plenty of excellent tutorials available on the internet. If you encounter any issues to which you can't find the answer -> Here , feel free to join our Facebook Group or open a new discussion topic in the dedicated tab. Remember that providing detailed information about the problem will help me offer more effective assistance. More information equals better help!

Arduino IDE Configuration

Note

Arduino IDE 2.3.2

Used Arduino Libraries

#include <Arduino.h>
#include <SPI.h>
#include <LoRa.h>
#include <WiFi.h>
#include <PubSubClient.h>
#include <ArduinoJson.h>
#include <esp_now.h>

CapiBridge is based on ESP32-C3 so If you are using ESP32 for the first time, you need To install the ESP32 board and all libraries, in your Arduino IDE.

• In your Arduino IDE, go to File> Preferences.
• Enter https://raw.githubusercontent.com/espressif/arduino-esp32/gh-pages/package_esp32_index.json into the “Additional Boards Manager URLs” field. Then, click the “OK” button
• Open the Boards Manager. Go to Tools > Board > Boards Manager and Search for ESP32 and press the install button for the “esp32 by Expressif Systems“
• Open Library Manager search for PubSubClient and press the install button, do the same for other libraries.

---

ESP1.ino sketch configuration

Note

For ESP1.ino all configurations are done in the file config.h

Gateway Key

Important

Unique key within the JSON to differentiate your signal from others. Must match the key in Nodes/Sensors.

#define GATEWAY_KEY "xy"

WIFI and MQTT Server Configuration

#define WIFI_SSID "your_wifi_ssid"
#define WIFI_PASSWORD "your_wifi_passwd"
#define MQTT_USERNAME "your_mqtt_user"
#define MQTT_PASSWORD "your_mqtt_passwd"
#define MQTT_SERVER "your_mqtt_broker_address"
#define MQTT_PORT 1883

LoRa Configuration

Important

LoRa configuration must match the configuration in Nodes/Sensors.

#define SIGNAL_BANDWITH 125E3  // signal bandwidth in Hz, defaults to 125E3
#define SPREADING_FACTOR 8    // ranges from 6-12, default 7 see API docs
#define CODING_RATE 5          // Supported values are between 5 and 8
#define SYNC_WORD 0xF3         // Any hexadecimal value from 0x00 to 0xFF. Dont use LoRaWAN/TTN "0x34"
#define PREAMBLE_LENGTH 6      // Supported values are between 6 and 65535.
#define TX_POWER 20            // TX power in dB, defaults to 17, Supported values are 2 to 20
#define BAND 433E6             // 433E6 / 868E6 / 915E6 - Depends on what board you bought.

Important

For optimizing the SPREADING_FACTOR (SF) in your network, it's crucial not to default to SF12 aiming for maximum distance without considering its downsides. SF12, while extending range, significantly slows down data transmission. For example, if your furthest sensor is only 100 meters away, opting for SF7 is more efficient. SF7 is faster, taking only 0.027 seconds to transmit "6 bytes", thus consuming less power compared to SF12, which would take 0.75 seconds for the same task. Therefore, it's essential to choose the SF wisely based on your specific needs and understand the trade-offs. Avoid setting SF12 by default without assessing the impact on speed, power consumption, and time on air (ToA) for others.

// For sending 6 bytes "6 characters" of data using different Spreading Factors (SF), the estimated time on air (ToA)
// for each SF is as follows:

// SF7: Approximately 0.027 seconds (27.494 milliseconds)
// SF8: Approximately 0.052 seconds (52.224 milliseconds)
// SF9: Approximately 0.100 seconds (100.147 milliseconds)
// SF10: Approximately 0.193 seconds (193.413 milliseconds)
// SF11: Approximately 0.385 seconds (385.297 milliseconds)
// SF12: Approximately 0.746 seconds (746.127 milliseconds)
// These calculations demonstrate how the time on air increases with higher Spreading Factors
// due to the decreased data rate, which is a trade-off for increased communication range and signal robustness.

---

ESP2.ino sketch configuration

Note

ESP2 for ESPNOW requires no initial setup, once the sketch is uploaded, it automatically prints the MAC address in the serial monitor for integration with ESPNOW nodes/sensors.

---

Uploading Code to CapiBridge

Warning

🔥Connect the antenna first to prevent damage to the transmitter.🔥

1. Open ESP1.ino sketch and configure config.h file see https://github.com/PricelessToolkit/CapiBridge?tab=readme-ov-file#esp1ino-sketch-configuration
2. Set the UART switch on the CapiBridge to the 'ESP1' position.

3. Select board type, COM port and... see the screenshot below.

4. Click Upload and wait until the upload is done.
5. Set the UART switch on the CapiBridge to the 'ESP2' position.

6. Open ESP2.ino sketch.
7. Click Upload.
8. Set the UART switch back to the ESP1 position to see received JSON messages.

Everything will be ready shortly; the CapiBridge RSSI entity should appear in the Home Assistant MQTT devices list within a minute or two.

---

Home Assistant Zero Configuration

Note

With MQTT-Autodiscovery, there's no need to configure anything in Home Assistant manually. Any sensor or node that sends a JSON string with special keys ('k' for the gateway private key and 'id' for the node name, both of which are mandatory) will be automatically discovered. Refer to the table below for details, and of course, full ESP32 examples are provided.

JSON String Sent by a Sensor/Node:

{
  "k": "xy",
  "id": "ESP32",
  "b": "99",
  "rw": "Test123",
  "dr": "on"
}

Full Suported MQTT-Autodiscovery List

Key	Description	Unit of Measurement	Required
k	Private Gateway key	-	Yes
id	Node Name	-	Yes
r	RSSI	dBm	No
b	Battery percent	%	No
v	Voltage	Volts	No
pw	Current	mAh	No
l	Luminance	lux	No
m	Motion	Binary on/off	No
w	Weight	grams	No
s	State	Anything	No
t	Temperature	°C	No
t2	Temperature 2	°C	No
hu	Humidity	%	No
mo	Moisture	%	No
rw	ROW	Anything	No
bt	Button	Binary on/off	No
atm	Pressure	kph	No
cd	Dioxyde de carbone	ppm	No
dr	Door	Binary on/off	No
wd	Window	Binary on/off	No
vb	Vibration	Binary on/off	No

Sensor / Node Example

The simplest way to create JSON String without the ArduinoJson.h library and transmit it via LoRa. Example from MailBox sensor

#define NODE_NAME "mbox"
#define GATEWAY_KEY "xy" // must match CapiBridge's key

float volts = analogReadEnh(PIN_PB4, 12) * (1.1 / 4096) * (30 + 10) / 10;
// Calculate percentage
float percentage = ((volts - 3.2) / (4.2 - 3.2)) * 100;
percentage = constrain(percentage, 0, 100);
int intPercentage = (int)percentage;
	
LoRa.print("{\"k\":\"" + String(GATEWAY_KEY) + "\",\"id\":\"" + String(NODE_NAME) + "\",\"s\":\"mail\",\"b\":" + String(intPercentage) + "}");

Troubleshooting

If your DIY sensor/assembly is not showing up in Home Assistant, here are some tips that may help you find the problem.

1. Check if the node LoRa settings are the same as the LoRa Gateway config, like Frequency, and spreading factor...
2. Connect CapiBridge to PC with switch position selected ESP1, open Arduino IDE Serial monitor "Speed 115200 baud" and check received JSON strings for errors.
3. Download MQTT Explorer and connect to your MQTT server. Check the homeassistant/sensor/Your_Node_Name topic for any errors.