Skip to content

flashrom serprog programmer based on STM32F103 MCU & USB CDC protocol. Uses libopencm3 and deprecates the old serprog-stm32vcp project.

License

Notifications You must be signed in to change notification settings

camoz/stm32-vserprog

 
 

Repository files navigation

stm32-vserprog:

flashrom serprog programmer based on STM32 MCU & USB CDC protocol.

This project deprecates previous serprog-stm32vcp project, which uses STMicro's proprietary firmware library. Most functions are the same.


Features

  • Fully opensource: now with libopencm3 instead of STMicro's proprietary firmware library.
  • Affordable and simple hardware:
    • A STM32F103C8T6 MCU, a 8MHz crystal, a 3.3V 1117 LDO, some 0805 capacitors, resistors and LEDs along with dedicated PCB available on OSH Park (V2 or V3)
    • Or some general-purpose STM32F0/STM32F1 development boards, just add a new header under "boards" folder to assign correct GPIO for USB D+ pullup (STM32F1 only) and LEDs.
    • Hardware USB2.0 FullSpeed and efficient virtual COM port with USB CDC protocol eliminates the need of USB-to-UART bridges and the headache that comes with them, operates at any baud rates.
    • Ironically, you will still have to buy or borrow a USB-to-UART bridge (not RS-232 but TTL level) to program the programmer itself, unless you are using a STM32F042 device (support is in progress).
  • Hardware full-duplex SPI with DMA, multiple clock speeds available (default at the one closest to but under 10MHz), e.g. on STM32F103 targets:
    • 36MHz
    • 18MHz
    • 9MHz (Default, for other boards the default is the one that is closest to 10MHz)
    • 4.5MHz
    • 2.25MHz
    • 1.125MHz
    • 562.5kHz
    • 281.25kHz
  • 2 status LEDs (controlled with 1 GPIO):
    • Busy is lit during operation.
    • Different operation causes different pattern of blinking: mostly busy = reading, both on = writing, flashing alternatively = erasing.
    • Busy blinks along if a hard fault or NMI is detected. Please unplug and replug the programmer. If situation persists, please consider opening a new ticket.
  • flashrom serprog protocol:
    • Operates under all major platforms (see flashrom wiki).
    • Driver-free under Linux. On Windows may require ST's VCP driver.
  • Interrupt-free except for low-level USB handling -- easy to debug and modify.
  • Fast:
    • Read speed up to 850KiB/s @ 36MHz SPI operation.
    • Dumps a EN25Q64 in 11 seconds and programs in 85 seconds (including flashrom calibration time).
    • Way faster than many commercial CH341-based USB programmers, especially for reading.
  • Support 25 and 26 series SPI flash chips. 45 series has different pinout, thus for the PCB provided with the project you will need an adapter.

Installation

  1. Install stm32flash and gcc-arm-none-eabi toolchain.

On Debian, simply do the following:

sudo apt-get install stm32flash gcc-arm-none-eabi
  1. Clone and compile.

Simply type (change the board name accordingly, for details see the header of the Makefile):

git clone https://github.com/dword1511/stm32-vserprog.git
make BOARD=stm32-vserprog-v2
  1. Program.

On dedicated PCB, solder the "PROG ENABLE" jumper, then connect it to a USB slot nearby the one that USB-to-UART bridge is using, then connect TXD and RXD lines with wires. For other boards, find the BOOT0 jumper or ISP switch, put it into high or enabled, then connect your board's UART to your computer with the USB-to-UART bridge and apply power to your board. Then type:

make BOARD=stm32-vserprog-v2 flash
  1. Done!

Throw the USB-to-UART bridge away and enjoy. Do not forget to desolder the jumper / pull BOOT0 low before resetting / replugging the board.


Usage

The following assuming Linux platform, and the programmer appears as /dev/ttyACM0.

  1. To read a flash chip:
  • Connect an 25 type SPI Flash to the board's DIP-8 slot or according to the schematics.
  • Connect your board to your PC via USB.
  • Type:
flashrom -p serprog:dev=/dev/ttyACM0:4000000 -r file-to-save.bin
  • Some times flashrom will ask you to choose a chip, add something like:
-c SST25VF040B

This is because sometimes multiple devices with different timing requirements can only be distinguished by the device code, however currently flashrom will not read it. Besides, some flash chips support more than one instruction sets.

  1. To erase a flash chip:
  • Erase is automatically done during writing. However, if you simply want an empty chip, you will need to erase manually.
  • Type:
flashrom -p serprog:dev=/dev/ttyACM0:4000000 -E
  • For certain chips like MX25L6445E, first pass could fail with old flashrom version, but if you do a second pass, everything will be alright. Seems that the first block needs more delay to be erased.
  • Flash status are verified to be empty automatically.
  • The whole process can take a few minutes.
  1. To write a flash chip:
  • Type:
flashrom -p serprog:dev=/dev/ttyACM0:4000000 -w file-to-load.bin
  • Flash chips are checked and blocks that are not empty are automatically erased.
  • Images are verified after writing automatically.
  • The whole process can take a few minutes.

Problems?

  1. If encountered something like "Error: Cannot open serial port: Device or resource busy", please try to stop or remove ModemManager.
  2. Check your wirings and flashrom version. Do not forget to power the flash chip itself.
  3. If you are sure it is caused by something wrong in the programmer's firmware, please open a new ticket and provide details such as the board you are using and flashrom's output. I appreciate your feedback.

About

flashrom serprog programmer based on STM32F103 MCU & USB CDC protocol. Uses libopencm3 and deprecates the old serprog-stm32vcp project.

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • Eagle 96.8%
  • C 2.9%
  • Makefile 0.3%