Skip to content

chrisjbremner/Wiznet_5500

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Wiznet W5500

This library allows you to communicate with a TCP/IP network (separate from an imp’s connection to the network) using the Wiznet W5500 chip. The W5500 chip is a hardwired TCP/IP embedded Ethernet controller. The W5500 is used by the impAccelerator™ Fieldbus Gateway.

This library supports SPI integration with the W5500.

To use this library, add #require "W5500.device.lib.nut:2.1.0" to the top of your device code.

W5500 Class Usage

Constructor: W5500(interruptPin, spi[, csPin][, resetPin][, autoRetry][, setMac])

Parameter Data Type Required Default Value Description
interruptPin imp pin object Yes N/A The pin represents a physical pin on the imp and is used for receiving interrupts from the W5500 chip. The pin can be any digital input that supports a callback on pin state change
spi imp spi object Yes N/A A configured SPI object
csPin imp pin object No null The pin represents a physical pin on the imp and is used to select the SPI bus. On the imp005 if you do not pass a pin into csPin you must configure the SPI with the USE_CS_L constant
resetPin imp pin object No N/A The pin represents a physical pin on the imp and is used for sending a hard reset signal to the W5500 chip
autoRetry Boolean No false Whether the library should automatically retry to open a connection should one fail. Note Not yet implemented
setMac Boolean No true Whether the library should set the MAC address of the chip to the imp’s own MAC (with the last bit flipped). This should be set to false when using a Wiznet Wiz550io board, since it has its own MAC address

Examples

// Setup for an imp005
speed <- 4000;
spi <- hardware.spi0;
spi.configure(CLOCK_IDLE_LOW | MSB_FIRST | USE_CS_L, speed);

resetPin <- hardware.pinN;
interruptPin <- hardware.pinXA;

wiz <- W5500(interruptPin, spi, null, resetPin);
// Setup for an imp001
speed <- 4000;
spi <- hardware.spi257
spi.configure(CLOCK_IDLE_LOW | MSB_FIRST, speed);

cs <- hardware.pin8;
resetPin <- hardware.pin9;
interruptPin <- hardware.pin1;

wiz <- W5500(interruptPin, spi, cs, resetPin);

W5500 Class Methods

configureNetworkSettings(sourceIP[, subnet_mask][, gatewayIP][, mac])

This method takes the network information and sets the data into the relevant registers in the Wiznet chip. It takes the following parameters:

Parameter Data Type Required Default Value Description
sourceIP String or an array of integers Yes N/A The IP address for Wiznet adapter. For example, the address 192.168.1.37 can be passed in as an array, [192, 168, 1, 37], or as a string "192.168.1.37"
subnet_mask String or an array of four integers No null The subnet mask. For example, a subnet mask of 255.255.255.0 can be passed in as an array, [255, 255, 255, 0], or as a string "255.255.255.0"
gatewayIP String or an array of four integers No null The IP address of the gateway or router. For example, the address 192.168.1.1 can be passed in as an array, [192, 168, 1, 1], or as a string "192.168.1.1"
mac String or an array of six integers No A function that will return the MAC address of the Wiznet The MAC address to assign to the Wiznet adapter. It is easiest to let the MAC address be set automatically by leaving this as null. You can manually enter the address 0c:2a:69:09:76:64 by passing it into an array, [0x0c, 0x2a, 0x69, 0x09, 0x76, 0x64], or as a string "0c2a69097664"

Example

// Configured using strings
wiz.configureNetworkSettings("192.168.1.37", "255.255.255.0", "192.168.1.1");
// Configured using arrays
wiz.configureNetworkSettings([192,168,1,37], [255,255,255,0], [192,168,1,1]);

onReady(callback)

Has method has a single, required argument: a callback function. The callback will be executed when the initialization of the W5500 has completed successfully. It will be called immediately if the initialization has already been completed. The callback takes no parameters.

Example

// The callback function will not run until the 5500 has finished initializing
wiz.onReady(function() {
  server.log("The Wiznet W5500 is ready");
}.bindenv(this));

openConnection(ip, port[, mode][, callback])

This method finds a socket that is not in use and initializes a connection for the socket. It takes the following parameters:

Parameter Data Type Required Default Value Description
ip String or an array of four integers Yes N/A The destination IP address. For example, the address 192.168.1.37 can be passed in as an array, [192, 168, 1, 37], or as a string "192.168.1.37"
port An integer or an array of two integers Yes N/A The destination port. For port 4242, pass in an array, [0x10, 0x92], or an integer 4242
mode Constant No W5500_SOCKET_MODE_TCP The mode of communication to be used by the socket. The list of available options is listed in the table below. Currently only TCP is supported
callback Function No null A callback function that is passed an error message or the opened connection. The callback’s parameters are listed below
Communication Mode Value
W5500_SOCKET_MODE_TCP 0x01
W5500_SOCKET_MODE_UDP 0x02
Callback Parameter Data Type Description
error String An error message if there was a problem, or null if successful
connection A W5500.Connection object An instantiated object representing the open socket connection

Examples

// Using a string and a integer
local destIp = "192.168.1.42";
local destPort = 4242;
wiz.openConnection(destIp, destPort, function(error, connection) {
  if (error) {
    server.error(error);
  } else {
    // Work with connection
  }
}.bindenv(this));
// Using arrays
local destIp = [192, 168, 1, 42];
local destPort = [0x10, 0x92];
wiz.openConnection(destIp, destPort, function(error, connection) {
  if (error) {
    server.error(error);
  } else {
    // Work with connection
  }
}.bindenv(this));

listen(port, callback)

This method function finds a socket that is not in use and sets up a TCP server. It has the following parameters:

Parameter Data Type Required Default Value Description
port An integer Yes N/A The port to listen on for connections
callback Function Yes N/A A callback function that is passed an error message, or the established remote connection is established. The table below lists its parameters
Callback Parameter Data Type Description
error String An error message if there was a problem, or null if successful
connection A W5500.Connection object An instantiated object representing the open socket connection

Example

local port = 80;
wiz.listen(port, function(error, connection) {
  if (error) {
    server.error(error);
  } else {
    local ip = connection.getIP();
    local port = connection.getPort();
    server.log(format("Connection established from %d.%d.%d.%d:%d", ip[0], ip[1], ip[2], ip[3], port));
  }
}.bindenv(this))

reset([softReset])

This method causes the Wiznet chip to undergo a reset. It is recommended that your use hardware resets (the default behaviour) and to wait for the onReady() callback to be triggered before proceeding after a reset.

The single parameter, softReset, is a Boolean value: pass true to trigger a soft reset, or false (the default) for a hard reset.

Examples

// Perform a hardware reset
wiz.reset();
wiz.onReady(function() {
  // Reset complete, so configure the Wiznet 5500 here
}.bindenv(this));
// A software reset
wiz.reset(true);
wiz.onReady(function() {
  // Reset complete, so configure the Wiznet 5500 here
}.bindenv(this));

setNumberOfAvailableSockets(numSockets)

This method configures the Wiznet 5500’s buffer memory allocation by dividing the available memory between the number of required sockets evenly. If you need a greater buffer per socket, allocate fewer sockets. The default behaviour is to allocate eight sockets.

Example

wiz.setNumberOfAvailableSockets(2);

isPhysicallyConnected()

This method returns true if the W5500 detects an Ethernet cable is plugged into the socket to which the chip is connected.

Example

server.log(format("Cable %s connected.", wiz.isPhysicallyConnected() ? "is" : "is not"));

forceCloseAllSockets()

This method closes all sockets by sending a disconnect request followed by a close request.

Example

wiz.forceCloseAllSockets();

getNumSocketsFree()

This method returns the number of sockets that are still available for use. The number is returned as an integer.

Example

if (wiz.getNumSocketsFree() == 0) server.error("Wiznet is busy.");

W5500.Connection Class Usage

This connection class is used to perform all actions using the connection. This includes initializing and ending a connection to a socket, as well as using the connection for transmission and reception of data packets.

You do no instantiate W5500.Connection objects yourself — they will be generated for you by the methods detailed above.

W5500.Connection Class Methods

open([callback])

This method opens a socket then sets up the connection. It is called as part of openConnection() and should not be called directly.

close([callback])

This method closes the connection on a socket then fires the supplied callback on completion of all stages of disconnection. This callback takes no parameters.

Example

connection.close(function(){
  server.log("Connection closed");
}.bindenv(this));

getSocket()

This method returns the ID of the socket.

Example

server.log("This connection is using socket " + connection.getSocket());

isEstablished()

This method returns a Boolean: true if a connection is established, otherwise false.

Example

server.log(connection.isEstablished() ? "established" : "not established");

onReceive([callback])

This method triggers the supplied callback function when data is received. The callback takes the following parameters:

Parameter Data Type Description
error String An error message if there was a problem, or null if it was successful
data Blob The data that was received

Example

connection.onReceive(function(error, data) {
  if (error) {
    server.error(error);
  } else {
    server.log("Received data: " + data);
  }
}.bindenv(this));

onDisconnect([callback])

This method triggers the supplied callback function when a disconnection takes place. The callback takes a single parameter of its own: error, which will be a string if an error occurred, or null.

Example

connection.onDisconnect(function(error) {
  if (error) server.error(error);
  server.log("Disconnected");
}.bindenv(this));

onClose([callback])

This method triggers the supplied callback function when the connection is fully closed and removed from the system. The callback takes no parameters.

Example

connection.onClose(function() {
  server.log("Connection closed");
}.bindenv(this));

transmit(transmitData[, callback])

This method is called within a connection to transmit the data through the socket.

Parameter Data Type Required Default Value Description
transmitData Blob or string Yes N/A The data to be transmitted
callback Function No null The callback is called in the event of data being successfully sent or in the event of a timeout. It has a single parameter into which is passed an error message if there was a problem, or null if transmission was successful

Example

local data = "Hello, world.";
connection.transmit(data, function(error) {
  if (error) {
    server.error(error);
  } else {
    server.log("Data sent successfully");
  }
}.bindenv(this));

receive([callback])

This method is an alternative to onReceive() and which will temporarily override onReceive(). It receives the next available data packet on the connection. If a callback is supplied, it should take the following two parameters:

Parameter Data Type Description
error String An error message if there was a problem, or null if it was successful
data Blob The data that was received

Example

connection.receive(function(error, data) {
  if (error) {
    server.error(error);
  } else {
    server.log("Received data: " + data);
  }
}.bindenv(this));

W5500.Driver Class

The W5500.Driver class is responsible for a number of low-levels operations, including opening and closing sockets, setting and getting memory, and setting and getting socket modes. The W5500 and W5500.Connection classes make use of this class.

License

The Wiznet code is licensed under the MIT License.

About

No description, website, or topics provided.

Resources

License

Stars

Watchers

Forks

Packages

No packages published

Languages

  • Squirrel 98.7%
  • JavaScript 1.3%