Skip to content

Third Official Release
Compare
Choose a tag to compare
@mrWheel mrWheel released this 31 Mar 12:16
· 54 commits to master since this release
v1.2.1
4cc846e

Let op!

Als je een update van de firmware doet, dan moet je alle bestanden die in de data map staan via de FSexplorer naar het SPIFFS uploaden!
Kijk ook hier

Arduino-IDE settings for DSMR-logger Version 4 (ESP-12):

    - Board: "Generic ESP8266 Module"
    - Flash mode: "DOUT" | "DIO"    // change only after power-off and on again!
    - Flash size: "4MB (FS: 2MB OAT:~1019KB)"  <<<<LET OP!! ***** 2MB SPIFFS *****
    - DebugT port: "Disabled"
    - DebugT Level: "None"
    - IwIP Variant: "v2 Lower Memory"
    - Reset Method: "none"   // but will depend on the programmer!
    - Crystal Frequency: "26 MHz" 
    - VTables: "Flash"
    - Flash Frequency: "40MHz"
    - CPU Frequency: "80 MHz"
    - Buildin Led: "2"  
    - Upload Speed: "115200"                                                                                                                                                                                                                                                 
    - Erase Flash: "Only Sketch"
    - Port: <select correct port>

Compiler opties Standaard:

#define USE_REQUEST_PIN           // define if it's a esp8266 with GPIO 12 connected to SM DTR pin
#define USE_UPDATE_SERVER         // define if there is enough memory and updateServer to be used
//  #define USE_BELGIUM_PROTOCOL      // define if Slimme Meter is a Belgium Smart Meter
//  #define USE_PRE40_PROTOCOL        // define if Slimme Meter is pre DSMR 4.0 (2.2 .. 3.0)
//  #define USE_NTP_TIME              // define to generate Timestamp from NTP (Only Winter Time for now)
//  #define HAS_NO_SLIMMEMETER        // define for testing only!
#define USE_MQTT                  // define if you want to use MQTT (configure through webinterface)
#define USE_MINDERGAS             // define if you want to update mindergas (configure through webinterface)
//  #define USE_SYSLOGGER             // define if you want to use the sysLog library for debugging
//  #define SHOW_PASSWRDS             // well .. show the PSK key and MQTT password, what else?

Compiler opties Belgische Slimme Meter:

#define HAS_REQUEST_PIN           // define if it's a 'bare' ESP-12 (no reset/flash functionality on board)
#define USE_UPDATE_SERVER         // define if there is enough memory and updateServer to be used
#define USE_BELGIUM_PROTOCOL      // define if Slimme Meter is a Belgium Smart Meter
//  #define USE_PRE40_PROTOCOL        // define if Slimme Meter is pre DSMR 4.0 (2.2 .. 3.0)
//  #define USE_NTP_TIME              // define to generate Timestamp from NTP (Only Winter Time for now)
//  #define HAS_NO_SLIMMEMETER        // define for testing only!
#define USE_MQTT                  // define if you want to use MQTT
//  #define USE_MINDERGAS             // define if you want to update mindergas
//  #define USE_SYSLOGGER             // define if you want to use the sysLog library for debugging
//  #define SHOW_PASSWRDS             // well .. show the PSK key and MQTT password, what else?

Compiler opties pre 40 (DSMR 2.2 tot 4.0):

#define HAS_REQUEST_PIN           // define if it's a 'bare' ESP-12 (no reset/flash functionality on board)
#define USE_UPDATE_SERVER         // define if there is enough memory and updateServer to be used
//  #define USE_BELGIUM_PROTOCOL      // define if Slimme Meter is a Belgium Smart Meter
#define USE_PRE40_PROTOCOL        // define if Slimme Meter is pre DSMR 4.0 (2.2 .. 3.0)
#define USE_NTP_TIME              // define to generate Timestamp from NTP (Only Winter Time for now)
//  #define HAS_NO_SLIMMEMETER        // define for testing only!
#define USE_MQTT                  // define if you want to use MQTT
#define USE_MINDERGAS             // define if you want to update mindergas
//  #define USE_SYSLOGGER             // define if you want to use the sysLog library for debugging
//  #define SHOW_PASSWRDS             // well .. show the PSK key and MQTT password, what else?

Arduino-IDE settings voor versie 2 en 3 van de DSMR-logger (ESP-01):

    - Board: "Generic ESP8266 Module"
    - Flash mode: "DOUT" | "DIO"    // change only after power-off and on again!
    - Flash size: "1MB (FS: 256KB OAT:~374KB)"  <<<<LET OP!! ***** 256KB SPIFFS *****
    - DebugT port: "Disabled"
    - DebugT Level: "None"
    - IwIP Variant: "v2 Lower Memory"
    - Reset Method: "none"   // but will depend on the programmer!
    - Crystal Frequency: "26 MHz" 
    - VTables: "Flash"
    - Flash Frequency: "40MHz"
    - CPU Frequency: "80 MHz" (or 160MHz)
    - Buildin Led: "2"  
    - Upload Speed: "115200"                                                                                                                                                                                                                                                 
    - Erase Flash: "Only Sketch"
    - Port: <select correct port>

Compiler opties voor versie 2 en 3 van de DSMR-logger (ESP-01):

/******************** compiler options  ********************************************/
//#define USE_REQUEST_PIN           // NIET VOOR EEN v3 BORDJE
//#define USE_UPDATE_SERVER         // (v3)NIET GEBRUIKEN
//  #define USE_BELGIUM_PROTOCOL      // define if Slimme Meter is a Belgium Smart Meter
//  #define USE_PRE40_PROTOCOL        // define if Slimme Meter is pre DSMR 4.0 (2.2 .. 3.0)
//  #define USE_NTP_TIME              // define to generate Timestamp from NTP (Only Winter Time for now)
//  #define HAS_NO_SLIMMEMETER        // define for testing only!
#define USE_MQTT                  // define if you want to use MQTT (configure through webinterface)
//  #define USE_MINDERGAS             // (v3) NIET GETEST!
//  #define USE_SYSLOGGER             // (v3) NIET GEBRUIKEN
//  #define SHOW_PASSWRDS             // well .. show the PSK key and MQTT password, what else?
/******************** don't change anything below this comment **********************/
Assets 2
Loading