mtd: nand: pxa3xx: Fix PIO FIFO draining

The NDDB register holds the data that are needed by the read and write commands. However, during a read PIO access, the datasheet specifies that after each 32 bytes read in that register, when BCH is enabled, we have to make sure that the RDDREQ bit is set in the NDSR register. This fixes an issue that was seen on the Armada 385, and presumably other mvebu SoCs, when a read on a newly erased page would end up in the driver reporting a timeout from the NAND. Cc: <[email protected]> # v3.14 Signed-off-by: Maxime Ripard <[email protected]> Reviewed-by: Boris Brezillon <[email protected]> Acked-by: Ezequiel Garcia <[email protected]> Signed-off-by: Brian Norris <[email protected]>
olajep · Feb 28, 2015 · 8dad038 · 8dad038
1 parent c517d83
commit 8dad038
Showing 1 changed file with 42 additions and 6 deletions.
diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
@@ -480,6 +480,42 @@ static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask)
 	nand_writel(info, NDCR, ndcr | int_mask);
 }
 
+static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len)
+{
+	if (info->ecc_bch) {
+		int timeout;
+
+		/*
+		 * According to the datasheet, when reading from NDDB
+		 * with BCH enabled, after each 32 bytes reads, we
+		 * have to make sure that the NDSR.RDDREQ bit is set.
+		 *
+		 * Drain the FIFO 8 32 bits reads at a time, and skip
+		 * the polling on the last read.
+		 */
+		while (len > 8) {
+			__raw_readsl(info->mmio_base + NDDB, data, 8);
+
+			for (timeout = 0;
+			     !(nand_readl(info, NDSR) & NDSR_RDDREQ);
+			     timeout++) {
+				if (timeout >= 5) {
+					dev_err(&info->pdev->dev,
+						"Timeout on RDDREQ while draining the FIFO\n");
+					return;
+				}
+
+				mdelay(1);
+			}
+
+			data += 32;
+			len -= 8;
+		}
+	}
+
+	__raw_readsl(info->mmio_base + NDDB, data, len);
+}
+
 static void handle_data_pio(struct pxa3xx_nand_info *info)
 {
 	unsigned int do_bytes = min(info->data_size, info->chunk_size);
@@ -496,14 +532,14 @@ static void handle_data_pio(struct pxa3xx_nand_info *info)
 				      DIV_ROUND_UP(info->oob_size, 4));
 		break;
 	case STATE_PIO_READING:
-		__raw_readsl(info->mmio_base + NDDB,
-			     info->data_buff + info->data_buff_pos,
-			     DIV_ROUND_UP(do_bytes, 4));
+		drain_fifo(info,
+			   info->data_buff + info->data_buff_pos,
+			   DIV_ROUND_UP(do_bytes, 4));
 
 		if (info->oob_size > 0)
-			__raw_readsl(info->mmio_base + NDDB,
-				     info->oob_buff + info->oob_buff_pos,
-				     DIV_ROUND_UP(info->oob_size, 4));
+			drain_fifo(info,
+				   info->oob_buff + info->oob_buff_pos,
+				   DIV_ROUND_UP(info->oob_size, 4));
 		break;
 	default:
 		dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__,