-
Notifications
You must be signed in to change notification settings - Fork 3
Commit
This commit does not belong to any branch on this repository, and may belong to a fork outside of the repository.
user guide: Switch over to Wintersong theme, remove surface mount kit…
… guide
- Loading branch information
Showing
12 changed files
with
353 additions
and
379 deletions.
There are no files selected for viewing
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| Original file line number | Diff line number | Diff line change |
|---|---|---|
|
|
@@ -8,167 +8,154 @@ Welcome to the build guide for Hydrogen's DIY kit. We hope you have a great time | |
|
|
||
| Please **read all instructions** thoroughly before starting. If you have questions or run into trouble please reach out to us on [discord] or drop us an email at [email protected]. | ||
|
|
||
| If you purchased the surface mount kit, head over to the [surface mount kit build guide](/surface-mount-build) before going through this one. | ||
|
|
||
| Some soldering experience is helpful but not required. If it's your first time soldering we recommend reading through [Adafruit's guide to excellent soldering](https://learn.adafruit.com/adafruit-guide-excellent-soldering). | ||
|
|
||
| This build takes around **one hour** to complete. | ||
|
|
||
| [discord]: https://discord.gg/UpfqghQ | ||
|
|
||
| ## Tools and materials required | ||
| ## Tools required | ||
|
|
||
| Before you begin, make sure that you've got: | ||
|
|
||
| - Safety glasses. Yes, **really**. A pair like [these][safety glasses] are fine. | ||
| - Proper ventilation, like this [small filtered fan](https://a.co/d/eUfPCRO). | ||
| - A **temperature-controlled** soldering iron, like this [Hakko] or the [Pinecil]. It is very important to use a temperature-controlled iron, since unregulated irons can easily get hot enough to damage components. You should set your iron temperature based on your solder manufacturer's recommendations. | ||
| - Solder. We recommend [Adafruit's SAC305 solder][adafruit solder] or [Kester 275 K100LD]. | ||
| - A small flat head screwdriver, like [this one][small screwdriver]. | ||
|
|
||
| !!! question "Flux" | ||
| We suggest using solder with "no clean" flux. If you use a different kind of flux, be sure to carefully clean the flux residue off based on the guidelines provided by the manufacturer of your solder. Take special care with the LEDs and potentiometers, as they can be damaged by water and flux cleaners. | ||
|
|
||
| Before jumping in, make sure you have: | ||
| [safety glasses]: https://a.co/d/dMXvPP6 | ||
| [tweezers]: https://www.adafruit.com/product/422 | ||
| [Hakko]: https://www.adafruit.com/product/1204 | ||
| [Pinecil]: https://pine64.com/product/pinecil-smart-mini-portable-soldering-iron/ | ||
| [adafruit solder]: https://www.adafruit.com/product/734 | ||
| [Kester 275 K100LD]: https://www.kester.com/products/product/275-flux-cored-wire | ||
| [flux pen]: https://www.sra-solder.com/sra-312-no-clean-flux-pen-refillable | ||
| [small screwdriver]: https://lovemyswitches.com/2mm-flat-head-screwdriver-for-knob-set-screws/ | ||
|
|
||
| * Safety glasses. Yes, really. | ||
| * Proper ventilation- at least open a window or two. | ||
| * A soldering iron, like [this one](https://www.adafruit.com/product/180). | ||
| * Solder, we can recommend [Adafruit's 60/40 **no-clean** rosin core solder](https://www.adafruit.com/product/145). We suggest using soldering with "no clean" flux. If you do use a different kind of flux, be sure to carefully clean the flux residue off based on the guidelines provided by the manufacturer of your solder. | ||
|
|
||
| ## Kit contents | ||
|
|
||
| Your kit should contain the following items. If any are missing please email us at [email protected]. | ||
|
|
||
| <object | ||
| alt="Kit contents" | ||
| data-is-svg-map | ||
| data-list="kit-contents-img-datalist" | ||
| data-stylesheet="/styles/kit-contents-svgmap.css" | ||
| data-info-text-template="kit-contents-img-info-text" | ||
| data="../images/kit.svg" | ||
| height="100%" | ||
| id="kit-contents-img" | ||
| type="image/svg+xml" | ||
| width="100%"> | ||
| </object> | ||
| <template id="kit-contents-img-info-text"> | ||
| <g id="info-text-container"> | ||
| <rect data-size-to="info-text"></rect> | ||
| <text id="info-text"></text> | ||
| </g> | ||
| </template> | ||
| <datalist id="kit-contents-img-datalist"> | ||
| <option value="mainboard">Mainboard</option> | ||
| <option value="panel">Front panel</option> | ||
| <option value="light-blocker">Light blocker</option> | ||
| <option value="jacks">1/8" jacks (10)</option> | ||
| <option value="nuts">Hex nuts for the 1/8" jacks (10)</option> | ||
| <option value="power-header">Eurorack power header (1)</option> | ||
| <option value="power-cable">Eurorack power cable (1)</option> | ||
| <option value="mounting-screws">M3x6 screws (4)</option> | ||
| <option value="rubber-bands">Rubber bands (2)</option> | ||
| <option value="glue-dot">Glue dot (1)</option> | ||
| </datalist> | ||
| <script type="module" src="/scripts/svgmap.js"></script> | ||
| <link rel="stylesheet" href="/styles/svgmap.css"/> | ||
| <winter-image-map src="../images/kit.svg"> | ||
| <winter-image-map-item id="mainboard">Mainboard</winter-image-map-item> | ||
| <winter-image-map-item id="panel">Front panel</winter-image-map-item> | ||
| <winter-image-map-item id="jacks">1/8" jacks (10)</winter-image-map-item> | ||
| <winter-image-map-item id="nuts">Hex nuts for the 1/8" jacks (10)</winter-image-map-item> | ||
| <winter-image-map-item id="power-header">Eurorack power header (1)</winter-image-map-item> | ||
| <winter-image-map-item id="rubber-bands">Rubber bands (2)</winter-image-map-item> | ||
| <winter-image-map-item id="light-blocker">Light blocker</winter-image-map-item> | ||
| </winter-image-map> | ||
|
|
||
| - (1) Mainboard | ||
| - (1) Front panel | ||
| - (1) Light blocker | ||
| - (1) Glue dot | ||
| - (10) 1/8" jacks | ||
| - (10) Hex nuts for the 1/8" jacks | ||
| - (1) Eurorack power header | ||
| - (1) Eurorack power cable | ||
| - (4) M3x6 screws for attaching the module to your rack | ||
| - (2) Rubber bands | ||
| - (1) Light blocker | ||
|
|
||
| !!! fairy "Light blocker" | ||
| Older kits include a little plastic square for the light blocker along with a glue dot, newer kits include a 3d-printed light blocker. The older one is pictured here. | ||
|
|
||
|
|
||
| ## Soldering the power header | ||
|
|
||
| Your first task is to place and solder the power header to the mainboard. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Place the power header onto the back side of the mainboard, being careful to align the notch in the header with the drawing on the board. The power header fits snugly, so you might have to give it a little pressure to push it all the way in. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Flip the board over to the front side and solder the header's 10 pins. It's important to **avoid touching the LEDs** with your iron, as it could melt and destroy the LEDs. Also, take care not to put too much solder on these joints as it could make it difficult to place the jacks. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| ## Placing the jacks | ||
|
|
||
| Next up is placing the ten jacks on the front side of the mainboard. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| The two jacks near the power header are placed according to the drawing on the board, with the third, bendy leg going into the adjacent hole. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| The other jacks are a bit trickier. Start by placing the jack for `Out B1` in the **same** orientation as the first two. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Then, place the jack for `Out B2` in the **opposite** orientation and place the third leg into the **same** hole as the adjacent jack's third leg. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| The jacks for `Out B3` and `Out B4` follow the same pattern - they are placed in opposite orientations and share a single hole for both of their third legs. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Repeat the same process to place the jacks for outs `A1`, `A2`, `A3`, and `A4`. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| ## Using the front panel as a jig | ||
|
|
||
| Since the jacks need to peek through the front panel, you can use it as a jig to make sure everything stays in the right place while soldering. Carefully line up the front panel's holes with the jacks and push the front panel on. | ||
| Since the jacks need to peek through the front panel, you can use it as a jig to make sure everything stays in the right place while soldering. Carefully line up the front panel's holes with the jacks and push the front panel on. Then, use the two rubber bands to temporarily hold the front panel on while you're working on it. You'll need to double over the rubber band to get it tight. Put the other rubber bands on the opposite side of the module so that everything is held down snugly. | ||
|
|
||
|  | ||
|
|
||
| Then, use the two rubber bands to temporarily hold the front panel on while you're working on it. You'll need to double over the rubber band to get it tight. | ||
|
|
||
|  | ||
|
|
||
|  | ||
|
|
||
| Put the two rubber bands on opposite sides of the module so that everything is held down snugly. | ||
|
|
||
|  | ||
| <winter-carousel> | ||
|  | ||
|  | ||
|  | ||
|  | ||
| </winter-carousel> | ||
|
|
||
| ## Soldering the jacks | ||
|
|
||
| With everything held in place, you can now flip the module over and solder all of the jacks in place. As you go, take a moment now and then to check that everything is flush with the panel and mainboard. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Once you've got most of the soldering done, you can move the rubber bands out of the way to get to the holes that they were covering up. You won't need the rubber bands again after this step, so feel free to give those a new purpose in life somewhere else. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| ## Placing the light blocker | ||
|
|
||
| Because the LEDs for Hydrogen's two channels are so close together, a small light blocker is used to keep them from bleeding into each other. You'll need the light blocker and the glue dot for this next step. | ||
| Because the LEDs for Hydrogen's two channels are so close together, a small light blocker is used to keep them from bleeding into each other. There are **two versions** of the light blocker out there: | ||
|
|
||
| * The **older** kits come with a simple plastic square and a glue dot. The instructions below are for this version. | ||
| * The **newer** kits come with a 3d-printed light blocker. You don't need to glue this one in place, just place it in-between the jacks with the **flat side** facing upwards. The faceplate will hold it in place. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Prepare the glue dot by peeling off the white paper. Don't remove the clear film yet. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Place the exposed side of the glue dot to the upper end of the long side of the light blocker and remove the plastic film. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Place the light blocker between the two sets of LEDs and stick the end with the glue dot against one of the jacks. The light blocker doesn't need to be perfectly straight. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| ## Putting the panel on | ||
|
|
||
| The last step it to place Hydrogen's lovely panel on and secure it with the hex nuts. You don't need to over-tighten the hex nuts, finger-tight is fine. | ||
|
|
||
|  | ||
|  | ||
|
|
||
| ## All done | ||
|
|
||
| Congratulations! You've finished your very own Hydrogen! | ||
|
|
||
|  | ||
|  | ||
|
|
||
| Now that it's all put together go check out the [User's Guide](/) and please show us your work by tweeting at [@wntrblm](https://twitter.com/wntrblm) or tagging [@wntrblm](https://instagram.com/wntrblm) in your instagram post. | ||
| Now that it's all put together go check out the [User's Guide](index.md) and please show us your work by tweeting at [@wntrblm](https://twitter.com/wntrblm) or tagging [@wntrblm](https://instagram.com/wntrblm) in your instagram post. | ||
|
|
||
Loading
Sorry, something went wrong. Reload?
Sorry, we cannot display this file.
Sorry, this file is invalid so it cannot be displayed.
Binary file not shown.
Oops, something went wrong.